BenQ W1060 Digital Projector User Manual

Operation 51
English
The INFORMATION menu shows you the current operating status of the projector.
FUNCTIONDESCRIPTION
Current 
System 
Status
Source
Shows the current signal source.
Picture Mode
Shows the selected mode in the PICTURE menu.
Resolution
Shows the native resoluti on of the input signal.
Color System
Shows input system format, NTSC, PAL, SECAM, or RGB.
Equivalent Lamp Hour
Displays the number of hours the lamp has been used.
Firmware Version
Displays the firmware version of the projector.
6....

Maintenance
52
EnglishMaintenance
Care of the projector
Your projector needs little maintenance. The only thing you need to do on a regular basis is 
to keep the lens clean.
Never remove any parts of the projector except the lamp. Contact your dealer if other parts 
need replacing.
Cleaning the lens
Clean the lens whenever you notice dirt or dust on the surface. 
• Use a canister of compressed air to remove dust. 
• If there is dirt or smears, use lens-cleaning pa per or moisten a soft cloth with lens...

Maintenance 53
EnglishLamp information
Getting to know the lamp hour
When the projector is in operation, the duration (in hours) of lamp usage is automatically 
calculated by the built-in timer. The method of calculating the equivalent lamp hour is as 
follows:
See  Setting Lamp mode as Economic  below for more information on Economic mode.
To obtain the lamp hour information:
1. Press Menu/Exit and then press  /  until the  SYSTEM SETUP: Advanced menu is 
highlighted.
2. Press   to highlight  Lamp...

Maintenance
54
EnglishTiming of replacing the lamp
When the  Lamp indicator  lights up red or a message appears suggesting it is time to replace 
the lamp, please install a new lamp or consult your dealer. An old lamp may cause a 
malfunction in the projector and in some instances the lamp may explode.
The Lamp indicator light and Temperature warning light will light up if the lamp becomes too 
hot. See  Indicators on page 58  for details.
The warning messages below are for reference only. Please follow...

Maintenance 55
EnglishReplacing the lamp
• If lamp replacement is performed while the projector is suspended upside-down from the ceiling, make sure that no one is underneath the lamp socket to avoid any possible injury 
or damage to the human eyes caused by fractured lamp.
• To reduce the risk of electrical shock, always turn the projector off and disconnect the  power cord before changing the lamp.   
• To reduce the risk of severe burns, allow the pr ojector to cool for at least 45 minutes 
before...

Maintenance
56
English
Do not turn the power on with the lamp cover removed.
5. Lift the handle so that it stands up. Use 
the handle to slowly pull the lamp out 
of the projector.
• Pulling it too quickly may cause the lamp to break and scatter broken glass in the 
projector.
• Do not place the lamp in locations where  water might splash on it, children can 
reach it, or near flammable materials.
• Do not insert your hands into the projector  after the lamp is removed. If you touch the 
optical...

Maintenance 57
EnglishResetting the lamp timer
11. After the startup logo, open the On-Screen Display (OSD) menu. Go to the  SYSTEM 
SETUP: Advanced > Lamp Settings  menu. 
Press  MODE/ENTER . The Lamp Settings  
page displays. Press   to highlight  Reset 
lamp timer  and press MODE/ENTER . A 
warning message displays asking if you 
want to reset the lamp timer. Highlight  Reset and press MODE/ENTER. The lamp 
time will be reset to 0.
Do not reset if the lamp is not new or replaced as this could cause...

Maintenance
58
EnglishIndicators
LightStatus & Description
PowerTe m pLamp
Power events
Orange Off OffStand-by mode
Green
Flashing Off OffPowering up
Green Off OffNormal operation
Orange
Flashing Off OffThe projector needs to cool for 90 seconds after the power is 
turned off.
Lamp events
Orange
Flashing Off RedThe lamp ignition retries if the lamp fails during startup.
Off Off Red1. The projector needs 90 seconds to cool down. 
Or
2. Please contact your dealer for assistance.
Thermal events
Off Red Off...

Troubleshooting 59
EnglishTroubleshooting
The projector does not turn on.
No picture
Blurred image
Remote control does not work
The password is incorrect
CauseRemedy
There is no power from the power 
cable.Plug the power cord into the AC inlet on the 
projector, and plug the power cord into the 
power outlet. If the power outlet has a switch, 
make sure that it is switched on.
Attempting to turn the projector on 
again during the cooling process. Wait until the cool
ing down process has 
completed....

Specifications
60
EnglishSpecifications
Projector specifications 
All specifications are subject to change without notice. 
General
Product name Digital Projector
Model name W1060
Optical
Resolution 1920 x 1080, 1080p
Display system 1-CHIP DMD
Lens F/Number F = 2.5 to 2.76, f = 23.5 to 28.2mm
Lamp 190 W lamp
Electrical
Power supplyAC100–240V, 50/60 Hz (Automatic)
Power consumption 250W (Max)/