BenQ W1060 Digital Projector User Manual

Operation 31
EnglishFine-tuning the image size and clarity
Correcting keystone
Keystoning refers to the situation where the projected image is noticeably wider at either the 
top or bottom. It occurs when the projector is not perpendicular to the screen. 
To correct this, besides adjusting the height of the projector, and use Auto Keystone or 
Ke ystone  to manually correct it following one of these steps.
•Using  Auto Keystone
It can correct  Ke ystone to optimal status by automatically.
• Using the...

Operation
32
EnglishMagnifying and searching for details
If you need to find the details on the projected picture, magnify the picture. Use the 
direction arrow keys for navigating the picture.
1. Press  MENU/EXIT  and then press  /  until the  DISPLAY menu is highlighted.
2. Press
  to highlight  Digital Zoom  and press MODE/ENTER . The Zoom bar displays.
3. Press   on the projector repeatedly to magnify the picture to a desired size.
4. To navigate the picture, press  MODE/ENTER to switch to the paning...

Operation 33
EnglishAbout the aspect ratio
In the pictures below, the black portions are inactive areas and the white portions are active 
areas. OSD menus can be displayed on those unused black areas.
1.Auto: 
Scales an image proportionally to fit the 
projector’s native resolution in its 
horizontal width and vertical height. 
This is suitable for the incoming image 
which is in 4:3 or 16:9 and you want to 
make most use of the screen without 
altering the image’s aspect ratio.
2. 16:9: 
Scales an...

Operation
34
English5. Real: 
The image is projected as its original 
resolution, and resized to fit within the 
display area. For input signals with lower 
resolutions, the projected image will 
display smaller than if resized to full 
screen. You could adjust the zoom 
setting or move the projector away from 
the screen to increase the image size if 
necessary. You may also need to refocus 
the projector after making these 
adjustments.
OSD menus can be displayed in the 
unused black areas.
4:3 picture 

Operation 35
EnglishOptimizing the image
Selecting a picture mode
The projector is preset with several predefined picture 
modes so that you can choose one to suit your operating 
environment and input signal picture type.
To select an operation mode that suits your need, you 
can follow one of the following steps.
•Press MODE/ENTER  on the projector repeatedly 
until your desired mode is selected.
•Go to the  PICTURE: Basic > Picture Mode  menu 
and press  /  to select a desired mode.
The picture modes...

Operation
36
EnglishFine-tuning the image quality in user modes
According to the detected signal type, there are some user-definable functions available 
when  User 1 , User 2  or User 3  mode is selected. You can make adjustments to these 
functions based on your needs.
Adjusting Brightness
Highlight  Brightness  in the PICTURE: Basic  menu and adjust the values by pressing  /  
on the projector or remote control.
The higher the value, the brighter the image. And lower 
the setting, darker the image....

Operation 37
EnglishAdjusting Clarity Control
Highlight Clarity Control  in the PICTURE: Advanced  menu and adjust the values by 
pressing  MODE/ENTER  on the projector or remote control.
To adjust the settings:
1. Noise Reduction: Reduces electrical image  noise caused by different media players. 
The higher the setting, the less the noise.
Highlight  Noise Reduction  and press  /  to adjust the value from 0 to 15.
2. Detail Enhancement: Sharpens the image. The higher the setting, the more details the...

Operation
38
EnglishSelecting a White Balance
Highlight  White Balance  in the PICTURE: Advanced  > Color Temperature Fine Tuning  > 
White Balance  menu and adjust the values by pressing  /  on the projector or remote 
control.
Choose a preferred white balance range: R-Ga in: -50~50/ G-Gain : -50~50/ B-Gain: -50~50/ 
R-Bias: -50~50/ G-Bias: -50~50/ B-Bias: -50~50.
Selecting a Gamma Selection
Highlight  Gamma Selection  in the PICTURE: Advanced  menu and select the modes by 
pressing /  on the projector...

Operation 39
EnglishTo adjust the settings:
1. Go to the PICTURE: Advanced  menu and highlight 3D Color Management .
2. Press  MODE/ENTER  and the 3D Color Management  page displays.
3. Highlight  Primary color and press  /  to select a color from among Red, Green, 
Blue, Cyan, Magenta and Yellow.
4. Press  to highlight  Hue and press  /  to select its range. Increase in the range 
will include colors consisted of more pr oportions of its two adjacent colors.
Please refer to the illustration to the right...

Operation
40
EnglishSelecting a Film Mode
Highlight  Film Mode  in the PICTURE: Advanced  menu and select by pressing  /  on the 
projector or remote control.
On  is the default and recommended selection for this projector. When  Off is selected, the 
Film Mode  function is not available.
This function is only available when Video or S-Video with NTSC system is selected.
Selecting a 3D Comb Filter
Highlight 3D Comb Filter in the PICTURE: Advanced  menu and select by pressing 
/  on the projector or...