BenQ W1060 Digital Projector User Manual

Operation 41
EnglishRemote Receiver
The Infrared Remote Receiver (Front and Top) 
allows the projector to accept signals from the 
remote control. For best results, be sure to aim 
the control toward the sensor without any 
obstructions between the two, and at a distance 
no greater than 7 meters.
You can set the remote receiver in the 
SYSTEM 
SETUP: Basic > Remote Receiver menu.
Freezing the image
Press  FREEZE  on the remote control to freeze the image. The word 
 FREEZE  will display in the upper...

Operation
42
EnglishAdjusting the sound
The sound adjustments made as below will have an effect on the projector speakers. Be sure 
you have made a correct connection to the projector audio input. See Connections on page 
19 for how the audio input is connected.
Muting the sound
To temporarily turn off the sound,
• Using the remote control
Press  MUTE to temporarily turn off the sound. While the sound is 
off, the screen will display   in th e upper right corner of the screen.
To restore the sound, press...

Operation 43
EnglishPersonalizing the projector menu display
The On-Screen Display (OSD) menus can be set according to your preferences. The 
following settings do not affect the projecti on settings, operation, or performance. 
• Menu display time  in the SYSTEM SETUP: Basic >  Menu Settings menu sets the length 
of time the OSD will remain active after your  last key press. The time length ranges from 
5 to 30 seconds in 5-second increments. Use  /  to select a suitable time frame.
• Menu position  in...

Operation
44
EnglishMenu operation
Menu system
Please note that the on-screen display (OSD) menus vary according to the signal type 
selected.
Main menu Sub-menu Options
1. 
PICTURE: 
Basic
Picture ModeBright/
Living Room/Gaming/Cinema//User 1/User 2/
User 3
Reference Mode Bright/Living Room/Gaming/Cinema
Brightness
Contrast
Color
Tint
Sharpness
Flesh Tone
Save Settings
Reset Picture 
Settings
2. 
PICTURE: 
Advanced
Clarity Control Noise Reduction/Detail 
Enhancement/Luma Transmission/
Chroma...

Operation 45
English
3. 
DISPLAY
Aspect RatioAuto/16:9/4:3/Letter Box/Real
Keystone Auto Keystone
On/Off
Keystone
Overscan 
Adjustment
Digital Zoom
PC & Component 
YPbPr Tuning Auto/H. Size/Phase/Horizontal 
position/Vertical position/SOG 
Level
Color Space 
Conversion Auto
/RGB/YUV
4.
SYSTEM 
SETUP: 
Basic
Language
Projector Position Front Table
/Rear Table/
Rear Ceiling/Front Ceiling
Menu Settings Menu Display Time
5 sec/10 sec/
15 sec/20 sec/25 sec/
30 sec
Menu position Top-Left/Top-Right/Center
/...

Operation
46
English
Note that the menu items are available when the projector detects at least one valid signal. If 
there is no equipment connected to the projector or no signal detected, limited menu items 
are accessible.
5. 
SYSTEM 
SETUP: 
Advanced
Audio Settings MuteOff/On
Volume Range : 0 ~ 10
Power on/off 
ring tone O
ff/ On
Lamp Settings Lamp Mode
Normal/Economic
Reset lamp timer
Equivalent Lamp Hour
HDMI Settings HDMI Format
Auto/PC Signal/Video Signal
HDMI Amplifier 
Gain Range:1 ~ 3
High...

Operation 47
EnglishDescription of each menu
FUNCTIONDESCRIPTION
Picture ModePre-defined picture modes are provided so you can optimize your 
projector image set-up to suit your program type. See Selecting a 
picture mode on page 35  for details.
Reference 
ModeSelects a picture mode that most suits your need for the image quality 
and further fine-tune the image based on the selections listed on the 
same page below.
BrightnessAdjusts the brightness of the image. See  Adjusting Brightness on 
page 36...

Operation
48
English
FUNCTIONDESCRIPTION
Clarity ControlSee  Adjusting Clarity Co ntrol on page 37 for details.
Gamma 
SelectionSelects gamma mode that most suits your need for the image quality. 
See Selecting a Gamma Selection on page 38  for details.
Brilliant ColorAdjusts the Brilliant Color value to extend the exposure range and 
sharpens detail for grain free images. 
See Adjusting Brilliant Color on page 38  for details.
White 
PeakingAdjusts white peaking while maintaining correct color...

Operation 49
English
FUNCTIONDESCRIPTION
LanguageSets the language for the On-Screen Display (OSD) menus. 
See  Using the menus on page 26  for details.
Projector 
PositionThe projector can be installed on a ceiling or behind a screen, or with 
one or more mirrors. 
See Choosing a location on page 15  for details.
Menu 
Settings
Menu display time
Sets the length of time the OSD will  remain active after your last key 
press. The range is from 5 to 30 seconds in 5-second increments.
Menu position
Sets the...

Operation
50
EnglishFUNCTIONDESCRIPTION
Audio 
Settings
Mute
Vo l u m e
Power On/Off Ring Tone
See  Adjusting the sound on page 42  for details.
Lamp 
Settings
Lamp Mode
See Setting Lamp mode as Economic on page 53  for details.
Reset Lamp Timer
See Resetting the lamp timer on page 57  for details.
Equivalent Lamp Hour
See Getting to know the lamp hour on page 53  for details on how 
the total lamp hour is calculated.
HDMI 
Settings
HDMI Format
Selects appropriate HDMI format automatically or manually....