BenQ Mp511 Dlp Users Manual
Here you can view all the pages of manual BenQ Mp511 Dlp Users Manual. The BenQ manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 51
Maintenance 51 Replacing the lamp • To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord before changing the lamp. • To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the lamp. • To reduce the risk of injuries to fingers and damage to internal components, use caution when removing lamp glass that has shattered into sharp pieces. • To reduce the risk of injuries to fingers and/or compromising image...
Page 52
Maintenance 524. Remove the lamp cords from the slots. 5. Disconnect the lamp connector by pushing it against the projector while pulling it up. 6. Loosen the screw that secures the lamp. 7. Lift the handle so that it stands up. Use the handle to slowly pull the lamp out of the projector. • Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector. • Do not place the lamp in locations where water might splash on it, children can reach it, or near flammable...
Page 53
Maintenance 53 14. Restart the projector. Do not turn the power on with the lamp cover removed. 15. After the startup logo, open the On-Screen Display (OSD) menu. Go to the SYSTEM SETUP: Advanced > Lamp Settings menu. Press ENTER. The Lamp Settings page displays. Highlight Reset Lamp Timer. A warning message displays asking if you want to reset the lamp timer. Highlight Reset and press ENTER. The lamp time will be reset to 0. Do not reset if the lamp is not new or replaced as this could cause...
Page 54
Maintenance 54 Indicators Illustration •Blank -: Light OFF •O: Orange light •: Light flashing•R: Red light •: Light ON•G: Green light LightStatus & Description PowerTe m pLamp Power events The projector has just been connected to a power outlet. --Stand-by mode. --Powering up. --Normal operation. -- 1. The projector needs 90 seconds to cool down as it was abnormally shut down without the normal cooling down process. Or 2. The projector needs to cool for 90 seconds after the power is turned off. --The...
Page 55
Maintenance 55 LightStatus & Description PowerTe m pLamp Thermal events -- The projector has shutdown automatically. If you try to re-start the projector, it w ill shutdow n again. Please contact your dealer for assistance. - - - - R R R R G RO R R R R R G R RO G R R G R G G RO O R R O R G O RO G R G G Downloaded From projector-manual.com BenQ Manuals
Page 56
Troubleshooting 56 Troubleshooting The projector does not turn on. No picture Blurred image Remote control does not work The password is incorrect CauseRemedy There is no power from the power cable.Plug the power cord into the AC inlet on the projector, and plug the power cord into the power outlet. If the power outlet has a switch, make sure that it is switched on. Attempting to turn the projector on again during the cooling process.Wait until the cooling down process has completed. CauseRemedy...
Page 57
Specifications 57 Specifications Projector specifications All specifications are subject to change without notice. General Product name Digital Projector Model name MP511+ Optical Resolution 800 x 600 SVGA Display system 1-CHIP DMD Lens F/Number F=2.57 (fixed) Lamp 180 W lamp Electrical Power supply AC100–240V, 2.9A, 50–60 Hz (Automatic) Power consumption 260 W (Max) Mechanical Weight 5.8 lbs (2.6 Kg) Input terminal Computer input RGB input D-Sub 15-pin (female) x 1 Video signal input S-VIDEO...
Page 58
Specifications 58 Timing chart Supported timing for PC input Supported timing for Component-YP bPr input Supported timing for Video and S-Video inputs ResolutionHorizontal Frequency (kHz)Ve rt i c a l Frequency (Hz)Pixel Frequency (MHz)Mode 640 x 48031.469 59.940 25.175 VGA_60 37.861 72.809 31.500 VGA_72 37.500 75.000 31.500 VGA_75 43.269 85.008 36.000 VGA_85 720 x 400 31.469 70.087 28.3221 720 x 400_70 800 x 60037.879 60.317 40.000 SVGA_60 48.077 72.188 50.000 SVGA_72 46.875 75.000 49.500...
Page 59
Warranty and Copyright information 59 Warranty and Copyright information Limited warranty BenQ warrants this product against any defects in material and workmanship, under normal usage and storage. Proof of purchase date will be required with any warranty claim. In the event this product is found to be defective within the warranty period, BenQs only obligation and your exclusive remedy shall be replacement of any defective parts (labor included). To obtain warranty service, immediately notify the...
Page 60
Regulation statements 60 Regulation statements FCC statement CLASS B: This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on,...