BenQ Mp511 Dlp Users Manual
Here you can view all the pages of manual BenQ Mp511 Dlp Users Manual. The BenQ manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 21
Connection 21 Connecting Video source devices You can connect your projector to various Video source devices that provide any one of the following output sockets: •Component Video •S-Video •Video (composite) You need only connect the projector to a Video source device using just one of the above connecting methods, however each provides a different level of video quality. The method you choose will most likely depend upon the availability of matching terminals on both the projector and the Video...
Page 22
Connection 22 Connecting a Component Video source device Examine your Video source device to determine if it has a set of unused Component Video output sockets available: • If so, you can continue with this procedure. • If not, you will need to reassess which method you can use to connect to the device. To connect the projector to a Component Video source device: 1. Take a Component Video to VGA (D-Sub) adaptor cable and connect the end with 3 RCA type connectors to the Component Video output sockets...
Page 23
Connection 23 Connecting an S-Video or a composite Video source device Examine your Video source device to determine if it has an unused S-Video output socket available: • If so, you can continue with this procedure. • If not, you will need to reassess which method you can use to connect to the device. If you have already made a Component Video connection between the projector and the video source device, you need not connect to this device again using an S-Video or composite Video connection as...
Page 24
Operation 24 Operation Start up 1. Plug the power cord into the projector and into a wall socket. Turn on the wall socket switch (where fitted). Check that the Power indicator on the projector lights orange after power has been applied. The power cable used in the illustration may look different to the power cable type used in your region. Use only the power cable as supplied with the projector, and which is suitable for your region. 2. Remove the lens cover. If it is closed, it could become...
Page 25
Operation 25 Utilizing the power-on lock function For security purposes and to help prevent unauthorized use, the projector includes an option for setting up password security. The password can be set through the On-Screen Display (OSD) menu. For details of the OSD menu operation, please refer to Using the menus on page 42. WARNING: You will be inconvenienced if you activate the power-on lock functionality and subsequently forget the password. Print out this manual (if necessary) and write the...
Page 26
Operation 26 Entering the password recall procedure Press and hold AU TO on the projector or remote control for 3 seconds. The projector will display a coded number on the screen. Write down the number and turn off your projector. Seek help from the local BenQ service center to decode the number. You may be required to provide proof of purchase documentation to verify that you are an authorized user of the projector. Changing the password 1. Open the OSD menu and go to the SYSTEM SETUP: Advanced >...
Page 27
Operation 27 Switching input signal The projector can be connected to multiple devices at the same time. However, it can only display one full screen at a time. Please decide if you want to activate the quick auto search function by performing the following steps. 1. Press MENU/Exit on the projector or remote control to turn on the OSD menu. 2. Go to SOURCE > Quick Auto Search menu. 3. Press Left or Right on the projector or remote control to select On or Off. 4. Press MENU/Exit to exit and save the...
Page 28
Operation 28 Adjusting the projected image Adjusting the projection angle The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These adjusters change the image height and projection angle. To adjust the projector: 1. Press the quick-release button and lift the front of the projector. Once the image is positioned where you want it, release the quick-release button to lock the foot in position. Do not look into the lens while the lamp is on. The strong light from the...
Page 29
Operation 29 Correcting keystone Keystoning refers to the situation where the projected image is noticeably wider at either the top or bottom. It occurs when the projector is not perpendicular to the screen. To correct this, besides adjusting the height of the projector, you will need to manually correct it following ONE of these steps. 1. Press or on the control panel of the projector or remote control to display the status bar labelled Keystone. Press to correct keystoning at the top of the...
Page 30
Operation 30• Using the OSD menu 1. Press MENU/Exit and then press Left or Right until the Display menu is highlighted. 2. Press Down to highlight Digital Zoom. 3. Press MODE/Enter and press Up to magnify the picture to a desired size. 4. Press MODE/Enter to activate the Pan functionality. 5. Use the directional arrows ( , , , ) on the projector or remote control to navigate the picture. 6. To reduce size of the picture, press MODE/Enter to switch back to the zoom in/out functionality, and press...