Home > BenQ > Projector > BenQ Mp511 Dlp Users Manual

BenQ Mp511 Dlp Users Manual

    Download as PDF Print this page Share this page

    Have a look at the manual BenQ Mp511 Dlp Users Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 702 BenQ manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Maintenance 51
    Replacing the lamp
    • To reduce the risk of electrical shock, always turn the projector off and disconnect the 
    power cord before changing the lamp.   
    • To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes 
    before replacing the lamp.
    • To reduce the risk of injuries to fingers and damage to internal components, use caution 
    when removing lamp glass that has shattered into sharp pieces.
    • To reduce the risk of injuries to fingers and/or compromising image quality by touching 
    the lens, do not touch the empty lamp compartment when the lamp is removed.
    • This lamp contains mercury. Consult your local hazardous waste regulations to dispose of 
    this lamp in a proper manner.
    • To assure optimal performance from the projector, it is recommended that you purchase a 
    BenQ projector lamp for lamp replacement.
    1. Turn the power off and disconnect the projector from the wall socket. If the lamp is 
    hot, avoid burns by waiting for approximately 45 minutes until the lamp has cooled. The lamp MUST be replaced before the projector 
    will operate normally.
    OK
    Lamp-usage time exceeded
    Replace lamp (refer to Users manual)
    Then reset lamp timer
    Notice
    2. Turn the projector over. Then loosen the 
    screws on the lamp cover. 
    3. Remove the lamp cover from the projector.
    Do not turn the power on with the lamp cover 
    removed.
    Downloaded From projector-manual.com BenQ Manuals 
    						
    							Maintenance 524. Remove the lamp cords from the slots.
    5. Disconnect the lamp connector by 
    pushing it against the projector while 
    pulling it up.
    6. Loosen the screw that secures the lamp.
    7. Lift the handle so that it stands up. Use the 
    handle to slowly pull the lamp out of the 
    projector.
    • Pulling it too quickly may cause the lamp to break 
    and scatter broken glass in the projector.
    • Do not place the lamp in locations where water 
    might splash on it, children can reach it, or near 
    flammable materials.
    • Do not insert your hands into the projector after 
    the lamp is removed. If you touch the optical 
    components inside, it could cause color 
    unevenness and distortion of the projected 
    images.
    8. As shown in the figure, hold the new lamp first 
    and align the lamp with the compartment in 
    the projector, and then insert the lamp all the 
    way into the projector.
    Downloaded From projector-manual.com BenQ Manuals 
    						
    							Maintenance 53 14. Restart the projector.
    Do not turn the power on with the lamp cover removed. 
    15. After the startup logo, open the On-Screen 
    Display (OSD) menu. Go to the SYSTEM 
    SETUP: Advanced > Lamp Settings menu. 
    Press ENTER. The Lamp Settings page 
    displays. Highlight Reset Lamp Timer. A 
    warning message displays asking if you want 
    to reset the lamp timer. Highlight Reset and 
    press ENTER. The lamp time will be reset to 0.
    Do not reset if the lamp is not new or replaced as this could cause damage. 
    Temperature information
    When the Temperature warning light is on, it is warning you of the following possible 
    problems:
    1. The internal temperature is too high.
    2. The fans are not working.
    Turn the projector off and contact qualified service personnel for further help. For more 
    detailed information, please refer to Indicators on page 54. 9. Tighten the screw that secures the lamp.
    • Loose screw may cause a bad connection, which 
    could result in malfunction.
    • Do not over tighten the screw.
    10. Connect the lamp connector to the projector.
    11. Place the lamp cords back to the slots.
    12. Replace the lamp cover on the projector.
    13. Tighten the screws that secure the lamp cover.
    • Loose screw may cause a bad connection, which 
    could result in malfunction.
    • Do not over tighten the screw.
    Reset Lamp Timer?
    Reset
    Cancel
    Notice
    Downloaded From projector-manual.com BenQ Manuals 
    						
    							Maintenance 54
    Indicators
    Illustration
    •Blank -: Light OFF
    •O: Orange light
    •: Light flashing•R: Red light
    •: Light ON•G: Green light
    LightStatus & Description
    PowerTe m pLamp
    Power events
    The projector has just been connected to a power outlet.
    --Stand-by mode.
    --Powering up.
    --Normal operation.
    --
    1. The projector needs 90 seconds to cool down as it was 
    abnormally shut down without the normal cooling down 
    process. Or
    2. The projector needs to cool for 90 seconds after the 
    power is turned off.
    --The projector has shutdown automatically. If you try to re-start 
    the projector, it will shutdown again. Please contact your dealer 
    for assistance.
    Lamp events
    -The projector has shutdown automatically. If you try to re-start 
    the projector, it will shutdown again. Please contact your dealer 
    for assistance.
    --1. The projector needs 90 seconds to cool down. Or
    2. Please contact your dealer for assistance.
      
      
    O O O
    O 
     G 
     G 
    O 
    O 
    O  R
     R
    Downloaded From projector-manual.com BenQ Manuals 
    						
    							Maintenance 55
    LightStatus & Description
    PowerTe m pLamp
    Thermal events
    --
    The projector has shutdown automatically. If you try to re-start 
    the projector, it w ill shutdow n again. Please contact your dealer 
    for assistance.
    -
    -
    -
    -
     R
     R R
     R G
     RO
     R  R R
     R  R G
     R  RO
     G  R R
     G  R G
     G  RO
    O  R R
    O  R G
    O  RO
     G R
     G G
    Downloaded From projector-manual.com BenQ Manuals 
    						
    							Troubleshooting 56
    Troubleshooting
    The projector does not turn on.
    No picture
    Blurred image
    Remote control does not work
    The password is incorrect
    CauseRemedy
    There is no power from the power 
    cable.Plug the power cord into the AC inlet on the 
    projector, and plug the power cord into the 
    power outlet. If the power outlet has a switch, 
    make sure that it is switched on.
    Attempting to turn the projector on 
    again during the cooling process.Wait until the cooling down process has 
    completed.
    CauseRemedy
    The video source is not turned on or 
    connected correctly.Turn the video source on and check that the 
    signal cable is connected correctly.
    The projector is not correctly 
    connected to the input source device.Check the connection.
    The input signal has not been 
    correctly selected.Select the correct input signal with the Source 
    key on the projector or remote control.
    The lens cover is still closed. Open the lens cover.
    CauseRemedy
    The projection lens is not correctly 
    focused.Adjust the focus of the lens using the focus 
    ring.
    The projector and the screen are not 
    aligned properly.Adjust the projection angle and direction as 
    well as the height of the unit if necessary.
    The lens cover is still closed. Open the lens cover.
    CauseRemedy
    The batteries are out of power. Replace the batteries with new ones.
    There is an obstacle between the 
    remote control and the projector.Remove the obstacle.
    You are too far away from the 
    projector.Stand within 8 meters of the projector.
    CauseRemedy
    You do not remember the password.Please see Entering the password recall pro-
    cedure on page 26 for details.
    Downloaded From projector-manual.com BenQ Manuals 
    						
    							Specifications 57
    Specifications
    Projector specifications 
    All specifications are subject to change without notice. 
    General
    Product name Digital Projector
    Model name MP511+
    Optical
    Resolution 800 x 600 SVGA
    Display system 1-CHIP DMD
    Lens F/Number F=2.57 (fixed)
    Lamp 180 W lamp
    Electrical
    Power supply AC100–240V, 2.9A, 50–60 Hz (Automatic)
    Power consumption 260 W (Max)
    Mechanical
    Weight 5.8 lbs (2.6 Kg)
    Input terminal
    Computer input
         RGB input D-Sub 15-pin (female) x 1
    Video signal input
         S-VIDEO Mini DIN 4-pin port x 1
         VIDEO RCA jack x 1
    SD/HDTV signal input D-sub  Component RCA jack x 3, through RGB input
    Control (for servicing)
    USB mouse connector A/B series x 1 (for servicing)
    RS-232 serial control mini Din 9 pin x 1
    Environmental Requirements
    Operating temperature 0°C ~ 40°C at sea level
    Operating relative humidity 10% ~ 90% (without condensation)
    Operating altitude 0–1499 m at 0°C–35°C
    1500–3000 m at 0°C–30°C (with High Altitude Mode on)
    208277
    95
    72
    78.5
    Dimensions277 mm (W) x 95 mm (H) x 208 mm (D)
    Downloaded From projector-manual.com BenQ Manuals 
    						
    							Specifications 58
    Timing chart
    Supported timing for PC input
    Supported timing for Component-YP
    bPr input
    Supported timing for Video and S-Video inputs
    ResolutionHorizontal 
    Frequency 
    (kHz)Ve rt i c a l  
    Frequency 
    (Hz)Pixel 
    Frequency 
    (MHz)Mode
    640 x 48031.469 59.940 25.175 VGA_60
    37.861 72.809 31.500 VGA_72
    37.500 75.000 31.500 VGA_75
    43.269 85.008 36.000 VGA_85
    720 x 400 31.469 70.087 28.3221 720 x 400_70
    800 x 60037.879 60.317 40.000 SVGA_60
    48.077 72.188 50.000 SVGA_72
    46.875 75.000 49.500 SVGA_75
    53.674 85.061 56.250 SVGA_85
    1024 x 76848.363 60.004 65.000 XGA_60
    56.476 70.069 75.000 XGA_70
    60.023 75.029 78.750 XGA_75
    68.667 84.997 94.500 XGA_85
    1280 x 768 47.77 60.09 80.768 SXGA_60
    1280 x 800 49.65 59.96 83.458 SXGA_60
    1280 x 1024 63.981 60.020 108.000 SXGA_60
    Signal FormatHorizontal 
    Frequency (kHz)Vertical Frequency 
    (Hz)
    480i(525i)@60Hz 15.73 59.94
    480p(525p)@60Hz 31.47 59.94
    576i(625i)@50Hz 15.63 50.00
    576p(625p)@50Hz 31.25 50.00
    720p(750p)@60Hz 45.00 60.00
    720p(750p)@50Hz 37.50 50.00
    1080i(1125i)@60Hz 33.75 60.00
    1080i(1125i)@50Hz 28.13 50.00
    Video modeHorizontal 
    Frequency 
    (kHz)Ve r t i c a l  
    Frequency 
    (Hz)Color sub-
    carrier 
    Frequency 
    (MHz)
    NTSC 15.73 60 3.58
    PAL 15.63 50 4.43
    SECAM 15.63 50 4.25 or 4.41
    PAL-M 15.73 60 3.58
    PAL-N 15.63 50 3.58
    PAL-60 15.73 60 4.43
    NTSC4.43 15.73 60 4.43
    Downloaded From projector-manual.com BenQ Manuals 
    						
    							Warranty and Copyright information 59
    Warranty and Copyright information
    Limited warranty
    BenQ warrants this product against any defects in material and workmanship, under normal 
    usage and storage. 
    Proof of purchase date will be required with any warranty claim. In the event this product is 
    found to be defective within the warranty period, BenQs only obligation and your exclusive 
    remedy shall be replacement of any defective parts (labor included). To obtain warranty 
    service, immediately notify the dealer from which you purchased the product of any defects.
    Important: The above warranty shall be void if the customer fails to operate the product in 
    accordance with BenQs written instructions, especially the ambient humidity must be in-
    between 10% and 90%, temperature in-between 0°C and 40°C, altitude lower than 10000 
    feet, and avoiding to operate the projector in a dusty environment. This warranty gives you 
    specific legal rights, and you may have other rights which vary from country to country.
    For other information, please visit www.BenQ.com.
    Copyright
    Copyright 2007 by BenQ Corporation. All rights reserved. No part of this publication may 
    be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any 
    language or computer language, in any form or by any means, electronic, mechanical, 
    magnetic, optical, chemical, manual or otherwise, without the prior written permission of 
    BenQ Corporation.
    Disclaimer
    BenQ Corporation makes no representations or warranties, either expressed or implied, 
    with respect to the contents hereof and specifically disclaims any warranties, merchantability 
    or fitness for any particular purpose. Further, BenQ Corporation reserves the right to revise 
    this publication and to make changes from time to time in the contents hereof without 
    obligation to notify any person of such revision or changes.
    *DLP, Digital Micromirror Device and DMD are trademarks of Texas Instruments. Others 
    are copyrights of their respective companies or organizations.
    Downloaded From projector-manual.com BenQ Manuals 
    						
    							Regulation statements 60
    Regulation statements
    FCC statement
    CLASS B: This equipment generates, uses and can radiate radio frequency energy and, if not 
    installed and used in accordance with the instructions, may cause harmful interference to 
    radio communications. However, there is no guarantee that interference will not occur in a 
    particular installation. If this equipment does cause harmful interference to radio or 
    television reception, which can be determined by turning the equipment off and on, the user 
    is encouraged to try to correct the interference by one or more of the following measures:
    — Reorient or relocate the receiving antenna.
    — Increase the distance between the equipment and receiver.
    — Connect the equipment into an outlet on a circuit different from that to which the 
    receiver is connected.
    — Consult the dealer or an experienced radio/TV technician for help.
    EEC statement
    This machine was tested against the 89/336/EEC (European Economic Community) for 
    EMC (Electronic Magnetic Compatibility) and fulfills these requirements.
    WEEE directive
    Disposal of Waste Electrical and Electronic Equipment by users in private households 
    in the European Union.
    This symbol on the product or on the packaging indicates that this can 
    not be disposed of as household waste. You must dispose of your waste 
    equipment by handling it over to the applicable take-back scheme for the 
    recycling of electrical and electronic equipment. For more information 
    about recycling of this equipment, please contact your city office, the shop 
    where you purchased the equipment or your household waste disposal 
    service. The recycling of materials will help to conserve natural resources 
    and ensure that it is recycled in a manner that protects human health and 
    environment.
      
    Downloaded From projector-manual.com BenQ Manuals 
    						
    All BenQ manuals Comments (0)

    Related Manuals for BenQ Mp511 Dlp Users Manual