BenQ Gp10 Users Manual

Operation31
Though the password function is disabled, you need to keep the old password in hand should you 
ever need to re-activate the password function by entering the old password.
Firmware upgrade
Follow below procedures to upgrade firmware version. 
• Only an SD Card is supported for a firmware update. 
• Do not remove the SD Card while an update is in progress. 
• Do not operate any buttons during the update. 
• Do not turn the projector off during the update. 
• To confirm that the firmware has...

Operation 32
Optimizing the image
Selecting a picture mode
The projector is preset with several predefined picture 
modes so that you can choose one to suit your 
operating environment and input signal picture type.
To select an operation mode that suits your need, you 
can follow one of the following steps.
• Make sure the input source is on computer, DVD 
player, composite video, component and HDMI 
mode and the projection screen is displayed.
•Press Mode on the remote control projector repeatedly...

Operation33
Using Wall Color
In the situation where you are projecting onto a colored surface such as a painted wall 
which may not be white, the Wall Color feature can help correct the projected picture’s 
color to prevent possible color difference between the source and projected pictures.
To use this function, press   to open the pop-up menu in one of the computer, iPhone/
iPod, composite video, component and HDMI modes. Select Wa l l  C o l o r and press  / 
 to select a color which is the closest to...

Operation 34
Operating in a high altitude environment
We recommend you use the High Altitude Mode when your environment is between 
1500 m –3000 m above sea level, and ambient temperature is between 0°C–30°C.
Do not use the High Altitude Mode if your altitude is between 0 m and 1499 m and ambient 
temperature is between 0°C and 35°C. The projector will be over cooled, if you turn the mode 
on under such a condition.
To activate the High Altitude Mode:
1. Hightlight Settings and press OK to enter.
2. Go...

Operation35 1. Hightlight Settings and press OK to enter.
2. Go to Advanced > Audio Settings and press 
OK to enter.
3. Highlight Mute and press OK to open the pop-up 
menu.
4. Highlight On and press OK to confirm.
5. To leave the OSD, press   until the projector 
returns to the home screen, or press   to go back to the home screen directly.
Adjusting the sound level
To adjust the sound level, press + or - on the remote control.
Turning off Power on/off ring tone
To turn off the Power on/off ring tone:...

Operation 36
Displaying images with PC and Video source
devices
You can connect your projector to a PC and various Video source devices. (e.g. HDMI, 
composite video, component video) However, you need only connect the projector to an 
input source device.
To display images:
1. Connect the projector to one of the above signal source.
2. Turn on the power of the projector and your source device. The projector displays 
the home screen.
3. Press  /   on the projector or remote control to select the input...

Operation37
Using PC/ Video pop-up menus
The projector has a multilingual OSD that allows you to make image adjustments and 
change a variety of settings. This menu is for the settings to be used in computer, DVD 
player, composite video, component and HDMI modes.
Using the menu
1. To open the OSD menu, press   on the projector or remote control when the 
projection screen is displayed.
2. When the OSD is displayed, press  /  to select the desired item and adjust the 
settings by using  / .
3. To leave...

Operation 38
Description of each menu
FUNCTIONDESCRIPTION
Wall ColorCorrects the projected picture’s color when the projection surface is 
not white. See Using Wall Color on page 33 for details.
Aspect RatioThere are four options to set the images aspect ratio depending 
on your input signal source. See Selecting the aspect ratio on 
page 31 for details.
Auto KeystoneAuto corrects any keystoning of the image.
Key s t o n eCorrects any keystoning of the image. See Correcting keystone 
on page 28 for...

Operation39
Displaying files with internal memory, USB
Drive and SD card
The projector can display files saved in internal memory or external storage like an SD 
card or a USB Drive when you have connected to projector.
To display files:
1. Turn on the power of the projector and the projector displays the home screen.
2. Connect the projector to one of the above external memory devices.
3. Press  /  to select SD card, USB Drive/Wireless Display or internal memory.
4. Storages are classified into Videos,...

Operation 40
When playing videos
Video player pop-up settings menu
The video player pop-up menu provides an on-screen display (OSD) for adjustments when 
playing videos.
Using the menu
1. To open the OSD menu, press   on the projector or remote control when the 
projection screen is displayed.
2. When the OSD is displayed, press  /  to select the desired item and adjust the 
settings by using  / .
3. To exit the OSD, press   on the projector or remote control again.
NAMEDESCRIPTION
OKPlay/Pause Plays or...