BenQ Gp10 Users Manual

Connection21
Connecting a Component Video source device
Examine your Video source device to determine if it has a set of unused Component Video 
output sockets available: 
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a Component Video source device:
1. Take a Component Video to VGA (D-Sub) adaptor cable and connect the end with 3 
RCA type connectors to the Component Video output sockets...

Connection 22
Connecting a composite Video source device
Examine your Video source device to determine if it has a set of unused composite Video 
output sockets available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a composite Video source device:
1. Take a Video cable and connect one end to the composite Video output socket of 
the Video source device.
2. Connect the other end of the...

Connection23
Connecting an external speaker
You can hear sound through an external speaker instead of the internal speakers built into 
the projector.
To connect the projector to an external speaker source device:
1. Connect an appropriate stereo cable to the external speaker and the audio output 
jack on the projector.
When the audio cable is connected to the audio output jack, the speaker output is muted. 
Downloaded From projector-manual.com BenQ Manuals 

Connection 24
Connecting to an external memory device
Connecting an SD card
To connect the projector to an SD card:
1. Connect an SD card to the SD card slot on the projector.
• The maximum memory capacity supported for an SD(HC) card is 32 GB. (The maximum 
capacity supported for external memory is based on our factory test. Your experience may 
differ depending on the manufacturer of the memory device.)
• The projector may not be compatible with some SD cards.
Connecting a USB storage device
To connect...

Connection25
• A USB storage device that uses only a designated driver might not be recognized. 
• Recognition speed for USB storage device may vary by device. 
• Do not turn off the product or pull a connected USB storage device out while the USB 
storage device is in use. Doing so may result in damage to the USB storage device or stored 
file. 
• Use a USB storage device which contains normal files. Abnormal files can cause a 
malfunction or the files may not play. 
• USB storages must be formatted in...

Operation 26
Operation
Starting up the projector
1. Connect the power using the power cord. The Power indicator turns into orange.
2. Press Power on the projector or remote 
control to start the projector. The Power 
indicator lights green when the projector is 
on.
The start up procedure takes several seconds. 
In the later stage of start up, a startup logo is 
projected.
(If necessary) Rotate the focus ring to adjust 
the image clearness.
3. If the projector is activated for the first time, select your...

Operation27
Adjusting the projected image
Adjusting the image height
The projector is equipped with 2 adjuster feet. This adjusters change the image height. To 
adjust the projector:
1. Screw the adjuster feet to adjust the image 
height.
To retract the feet, screw the adjuster feet in a 
reverse direction.
If the projector is not placed on a flat surface or 
the screen and the projector are not 
perpendicular to each other, the projected image 
becomes trapezoidal. To correct this situation, see...

Operation 28
Correcting keystone
Keystoning refers to the situation where the projected image is noticeably wider at either 
the top or bottom. It occurs when the projector is not perpendicular to the screen. 
Correcting keystone when an image is displayed on the screen.
To correct this, besides adjusting the height of the projector, you will need to manually 
correct it following one of these steps.
1. Press   and then press   to highlight 
Keystone. The Keystone pop-up menu 
displays.
2. Press   to...

Operation29
Securing the projector
Utilizing the password function
For security purposes and to help prevent unauthorized use, the projector includes an 
option for setting up password security. The password can be set through the Settings 
menu.
You will be inconvenienced if you activate the power-on lock functionality and subsequently 
forget the password. Print out this manual (if necessary) and write the password you used in this 
manual, and keep the manual in a safe place for later recall.
Setting...

Operation 30
Entering the password recall procedure
1. Press and hold   on the remote control for 3 
seconds. The projector will display a coded 
number on the screen.
2. Write down the number and turn off your 
projector.
3. Seek help from the local BenQ service center to 
decode the number. You may be required to 
provide proof of purchase documentation to 
verify that you are an authorized user of the projector.
Changing the password
1. Go to the Settings > Advanced > Security Settings > Change...