BenQ Fp202w User Manual

							
31 How to adjust your monitor   
Input Select:
Press the 
t or u keys to select D-sub 
(analog) or DVI (digital) input to activate the 
new settings.
Press the  Exit key to return to previous menu.
 
Sharpness:
Press the 
t or u keys to adjust the degree of 
Sharpness .
Press the  Exit key to return to previous menu.
 
Display Information:
Select  Display Information  to display the 
current monitor property settings. 
Press the  Exit key to return to previous menu.
 
 
						

							
  32
   Troubleshooting
Troubleshooting
Frequently Asked Questions (FAQ)
The image is blurred:
Read the  How to adjust the screen resolution on page18  section, and then select the correct 
resolution, refresh rate and make adjustments based on these instructions.
How do you use a VGA extension cable?
Remove the extension cable for the test. Is the imag e now in focus? If not, optimize the image by 
working through the instructions in the 
How to adjust the screen refresh rate on page19 section It 
is normal for blurring to occur due to conduction losses in extension cables. You can minimize 
these losses by using an extension cable with better  conduction quality or with a built-in booster.
Does the blurring only occur at resolutions lower than the native (maximum) resolution?
Read the How to adjust the screen resolution on page18 section. Select the native resolution.
Pixel errors can be seen:
One of several pixels is permanently black, one or  more pixels are permanently white, one or more 
pixels are permanently red, green, blue or another color.
•   Clean the LCD screen.
•   Cycle power on-off.
•   These are pixels that are permanently on or off and is a natural defect that occurs in LCD 
technology.
The image has a faulty coloration:
It has a yellow, blue or pink appearance.
On the monitor, press “Enter” key and press t or u key to move to the “Recall” icon and press 
“Enter” key to enter “Recall” sub menu. Press 
t or u key to select “Color Recall” and select 
“Yes” in “Color Recall” sub menu, then press “Enter” key to recall to factory settings. If the image 
is still not correct and the OSD also has faulty  coloration, this means one of the three primary 
colors is missing in the signal input. Now check the signal cable connectors. If any pin is bent or 
broken off, please contact your dealer to get necessary support.
No image can be seen:
Is the prompt on the display illuminated in green?
If the LED is illuminated in green  and there is a message “Out of Range” on the screen, this means 
you are using a display mode that this monitor  does not support, please change the setting to one 
of the supported mode. Please read “
Supported PC Timings on page34” section. Recommended 
mode is 1680 x 1050 @ 60Hz.
Is the prompt on the display illuminated in orange?
If the LED is illuminated in orange, the power ma nagement mode is active. Press any button on 
the computer keyboard or move the mouse. If  that does not help, check the signal cable 
connectors. If any pin is bent or broken off, plea se contact your dealer to get necessary support.
Is the prompt on the display not illuminated at all?
Check the power supply mains socket, the external power supply and the mains switch.
11
19
 
						

							
33 Troubleshooting   
The image is distorted, flashes or flickers:
Read the How to adjust the screen resolution on page18  section and then select the correct 
resolution, refresh rate and make adjustments based on these instructions.
The image is displace d in one direction:
Read the  How to adjust the screen resolution on page18  section and then select the correct 
resolution, refresh rate and make adjustments based on these instructions.
Need More Help?
If your problems remain after checking this ma nual, please contact your place of purchase or 
e-mail us at: [email protected]
 
						

							
  34
   Supported PC Timings
Supported PC Timings
• Image disruption may occur as a result of signal  frequency differences from graphics cards which 
do not correspond with the usual standard. This is  not, however, an error. You may improve this 
situation by altering an automatic setting or by  manually changing the phase setting and the pixel 
frequency from the “Geometry” menu. 
• To extend the service life of the product, we  recommend that you use your computers power 
management function. 
1 1
110
Incoming display m
ode (Input timing)
ResolutionHorizontal 
Frequency (KHz)Ve r t i c a l  
Frequency (Hz)Pixel 
Frequency (MHz)Comment
640x350 31.47 70.08 25.17 DOS
720x400 31.47 70.08 28.32 DOS
640x480 31.47 60.00 25.18 DOS
640x480 35.00 67.00 30.24 Macintosh
640x480 37.86 72.80 31.50 VESA
640x480 37.50 75.00 31.50 VESA
800x600 37.88 60.32 40.00 VESA
800x600 48.08 72.19 50.00 VESA
800x600 46.87 75.00 49.50 VESA
832x624 49.72 74.55 57.29 Macintosh
1024x768 48.36 60.00 65.00 VESA
1024x768 56.48 70.10 75.00 VESA
1024x768 60.02 75.00 78.75 VESA
1024x768 60.24 74.93 80.00 Macintosh
1152x864 67.50 75.00 108.00 VESA
1152x870 68.68 75.06 100.00 Macintosh
1152x900 61.80 66.00 94.50 SUN 66
1152x900 71.81 76.14 108.00 SUN
1280x1024 64.00 60.00 108.00 VESA
1280x1024 75.83 71.53 128.00 IBMI
1280x1024 80.00 75.00 135.00 VESA
1280x1024 81.18 76.16 135.09 SPARC2
1680x1050 75.00 60.00 162.00 VESA
 
						

							
35 Specifications   
Specifications
BenQ FP202W
11
111
ModelFP202W
Display type 
Viewable diagonal 
Native (maximum) resolution
Colors
Contrast / Brightness
Response time 
Viewing angle (left/right, up/down)  20.1 , active, TFT
51.1 cm
1,680 x 1,050 @ 60 Hz *
16.7
 million
600:1 / 300 cd/m
2
8 ms
140, 130 (CR=10)
Line frequency 
Image frequency 31 - 81 kHz Multi- 
frequency monitor
56 - 76 Hz, exception: 1680 x 1050 @ 60 Hz 
(Max.) only
Image diagnostics
Controls 
Functions Digital, OSD Technology,
 i  key (automatic image 
setting)  
7 buttons and  i key .
Contrast, brightness, ve rt. & hor. image position, 
phase, pixel clock, color  balance, color palette, 
multiple-language OSD, OSD position, status 
indicator, display-mode av ailibility, input selection
Power management
Max. power consumption 
Power saving mode VESA DPMS, EPA
60 Watt
<
 1 Watt, 120V
<
 2 Watt, 240V
Input signal 
Synchronisation RGB analog 0.7 Vpp/75 Ohm positive 
Digital: DVI-D (optional)
TTL separate signal connection 15-pin mini D-sub 
cable
 
Temperature (operating) 
Air humidity (operating) 0 °C - 40 °C
10% - 90%
Certifications TCO 99/03 (opti onal), TÜV/Ergonomics, TÜV/ 
GS, FCC Class B, ISO  13406-2, VCCI, CSA, CB 
Report, CE, C-Tick, BSMI , Fimko, GOST, CCC, 
UL, PSB, SASO
 
						

							
  36
   Specifications
   *   Please note that not all graphics cards will  support the video resolution of 1680 x 1050. To obtain 
the optimal display performance, please inqu ire with the system manufacturer to confirm 
resolution support, or you may consider buying a graphics card supporting the resolution of 1680 
x 1050. 
Operating voltage 
Dimensions (H x W x D) 
Weight Automatic switched mode power supply, 
100-260 V, 50-60 Hz
396.7 x 479.6 x 169.9 mm
5.7 kg