BEKO WMD 66120 User Manual

							WMD 66160
WMD 66140 S
WMD 66140
WMD 66120 S
WMD 66120Washing Machine
Wasmachine
Lave-linge
Waschmaschine
 
						

							2 - EN
1 Warnings
General Safety•	 Never	place	your	machine	on	a	carpet	covered	floor.	Otherwise,	lack	of	airflow	
from	below	of	your	machine	may	cause	
electrical	parts	to	overheat.	This	may	
cause	problems	with	your	washing	
machine.
•	 If	the	power	cable	or	mains	plug	is	 damaged	 you	must	 call	Authorized	 Service	
for	repair.
•	 Fit	the	drain	hose	into	the	discharge	 housing	securely	to	prevent	any	water	
leakage	and	to	allow	machine	to	take	in	
and	discharge	water	as	required.	It	is	very	
important	that	the	water	intake	and	drain	
hoses	are	not	folded,	squeezed,	or	broken	
when	the	appliance	is	pushed	into	place	
after	it	is	installed	or	cleaned.
•		 Your	washing	machine	is	designed	to	 continue	operating	in	the	event	of	a	power	
interruption.	Your	machine	will	not	resume	
its	program	when	the	power	restores.	
Press	the	“Start/Pause/Cancel”	button	for	
3	seconds	to	cancel	the	program	(See,	
Canceling	a	Program)
•		 There	may	be	some	water	in	your	machine	 when	you	receive	it.	This	is	from	the	
quality	control	process	and	is	normal.	It	is	
not	harmful	to	your	machine.
•	 Some	problems	you	may	encounter	 may	be	caused	by	the	infrastructure.	
Press	"Start/Pause/Cancel"	button	for	
3	seconds	to	cancel	the	program	set	in	
your	machine	before	calling	the	authorized	
service.
First Use•		 Carry	out	your	first	washing	process	without	loading	your	machine	and	with	
detergent	under	“Cottons	90°C”	program.
•	 Ensure	that	the	cold	and	hot	water	 connections	are	made	correctly	when	
installing	your	machine.
•	 If	the	current	fuse	or	circuit	breaker	is	less	 than	16	Amperes,	please	have	a	qualified	
electrician	install	a	16	Ampere	fuse	or	
circuit	breaker.
•	 While	using	with	or	without	a	transformer,	 do	not	neglect	to	have	the	grounding	
installation	laid	by	a	qualified	electrician.	
Our	company	shall	not	be	liable	for	
any	damages	that	may	arise	when	
the	machine	is	used	on	a	line	without	
grounding.
•	 Keep	the	packaging	materials	out	of	reach	 of	children	or	dispose	them	by	classifying	
according	to	waste	directives.
Intended use•	 This	product	has	been	designed	for	home	use.
•		 The	appliance	may	only	be	used	for	 washing	and	rinsing	of	textiles	that	are	
marked	accordingly.
Safety instructions•		 This	appliance	must	be	connected	to	an	earthed	outlet	protected	by	a	fuse	of	
suitable	capacity.
•		 The	supply	and	draining	hoses	must	 always	be	securely	fastened	and	remain	in	
an	undamaged	state.
•	 Fit	the	draining	hose	to	a	washbasin	 or	bathtub	securely	before	starting	up	
your	machine.	There	may	be	a	risk	of	
being	scalded	due	to	high	washing	
temperatures!
•	 Never	open	the	loading	door	or	remove	 the	filter	while	there	is	still	water	in	the	
drum.
•		 Unplug	the	machine	when	it	is	not	in	use.
•	 Never	wash	down	the	appliance	with	a	 water	hose!	There	is	the	risk	of	electric	
shock!
•		 Never	touch	the	plug	with	wet	hands.	Do	 not	operate	the	machine	if	the	power	cord	
or	plug	is	damaged.
•		 For	malfunctions	that	cannot	be	solved	by	 information	in	the	operating	manual:
•	 Turn	off	the	machine,	unplug	it,	turn	off	 the	water	tap	and	contact	an	authorized	
service	agent.	You	may	refer	to	your	local	
agent	or	solid	waste	collection	center	in	
your	municipality	to	learn	how	to	dispose	
of	your	machine.		
If there are children in your house...•		 Keep	children	away	from	the	machine	when	it	is	operating.	Do	not	let	them	
tamper	with	the	machine.
•		 Close	the	loading	door	when	you	leave	the	 area	where	the	machine	is	located.
Downloaded From WashingMachine-Manual.com Manualë 
						

							3 - EN
2 Installation
Removing packaging reinforcementTilt	the	machine	to	remove	the	packaging	
reinforcement.	Remove	the	packaging	
reinforcement	by	pulling	the	ribbon.
Opening the transportation locks
A	Transportation	safety	bolts	must	be	removed	before	operating	the	washing	
machine!	Otherwise,	the	machine	will	be	
damaged!
1.	 Loosen	all	the	bolts	with	a	spanner	until	 they	rotate	freely	(“C”)
2.	 Remove	transportation	safety	bolts	by	 turning	them	gently.
3.	 Fit	the	covers	(supplied	in	the	bag	with	the	 Operation	Manual)	into	the	holes	on	the	
rear	panel.	(“P”)
C Keep	the	transportation	safety	bolts	in	
a	safe	place	to	reuse	when	the	washing	
machine	needs	to	be	moved	again	in	the	
future.
C Never	move	the	appliance	without	the	
transportation	safety	bolts	properly	fixed	in	
place!
Adjusting the feet
A	Do	not	use	any	tools	to	loosen	the	lock	nuts.	Otherwise,	they	can	be	damaged.
1.	 Manually	(by	hand)	loosen	the	lock	nuts	on	 the	feet.
2.	 Adjust	them	until	the	machine	stands	level	 and	firmly.
3.	 Important:	Tighten	all	lock	nuts	up	again.
Connecting to the water supply.Important:
•		 The	water	supply	pressure	required	to	run	 the	machine	must	be	1-10	bar	(0,1	–	1	
MPa).
•		 Connect	the	special	hoses	supplied	with	 the	machine	to	the	water	intake	valves	on	
the	machine.	
•	 In	order	to	prevent	water	leakage	that	may	 occur	at	the	connection	points,	there	are	
rubber	seals	(4	seals	for	the	models	with	
double	water	inlet	and	2	seals	for	other	
models)	attached	to	the	hoses.	These	 seals	should	be	used	at	the	tap	and	
machine	connection	ends	of	the	hoses.	
The	plain	end	of	the	hose	fitted	with	a	
filter	must	be	attached	to	the	tap	and	the	
elbowed	end	must	be	attached	to	the	
machine.	Tighten	the	nuts	of	the	hose	well	
by	hand;	never	use	wrenches	to	tighten	
the	nuts.
•	 Models	with	a	single	water	inlet	should	not	 be	connected	to	the	hot	water	tap.
When	returning	the	appliance	to	its	place	after	
maintenance	or	cleaning,	care	should	be	taken	
not	to	fold,	squeeze	or	block	the	hoses.
Connecting to the drainThe	water	discharge	hose	can	be	attached	to	the	
edge	of	a	washbasin	or	bathtub.	The	drain	hose	
should	be	firmly	fitted	into	the	drain	as	to	not	get	
out	of	its	housing.
Important:
•		 The	end	of	the	drain	hose	must	be	directly	 connected	to	the	wastewater	drain	or	to	
the	washbasin.
•		 The	hose	should	be	attached	to	a	height	 of	at	least	40	cm,	and	100	cm	at	most.
•		 In	case	the	hose	is	elevated	after	laying	it	 on	the	floor	level	or	close	to	the	ground	
(less	than	40	cm	above	the	ground),	water	
discharge	becomes	more	difficult	and	the	
laundry	may	come	out	wet.
•		 The	hose	should	be	pushed	into	the	 drainage	for	more	than	15	cm.	If	it	is	too	
long	you	may	have	it	shortened.
•	 The	maximum	length	of	the	combined	 hoses	must	not	be	longer	than	3.2	m.
Electrical connectionConnect	the	machine	to	an	earthed	outlet	
protected	by	a	fuse	of	suitable	capacity.
Important:
•		 Connection	should	comply	with	national	
Downloaded From WashingMachine-Manual.com Manualë 
						

							4	-	EN
regulations.
•		 The	voltage	and	the	allowed	fuse	 protection	are	specified	in	the	section	
“Technical	Specifications”.
•		 The	specified	voltage	must	be	equal	to	 your	mains	voltage.
•		 Connection	via	extension	cords	or	multi- plugs	should	not	be	made.
B	A	damaged	 power	cable	must	be	replaced	
by	a	qualified	electrician.
B	The	appliance	must	not	be	operated	 unless	it	is	repaired!	There	is	the	risk	of	
electric	shock!
3 Initial preparations for 
washing
Preparing clothes for washingLaundry	items	with	metal	attachments	such	as,	
bras,	belt	buckles	and	metal	buttons	will	damage	
the	machine.	Remove	metal	attachments	or	
place	the	items	in	a	clothing	bag,	pillow	case,	or	
something	similar.
•	 Sort	the	laundry	according	to	type	of	 fabric,	color,	and	degree	of	soiling	and	
permissible	water	temperature.	Always	
follow	the	advice	on	the	garment	labels.
•		 Place	small	items	like	infants’	socks	and	 nylon	stockings,	etc.	in	a	laundry	bag,	
pillow	case	or	something	similar.	This	will	
also	save	your	laundry	from	getting	lost.
•		 Wash	“machine	washable”	or	“hand	 washable”	labeled	products	only	with	an	
appropriate	program.
•		 Do	not	wash	colors	and	whites	together.	 New,	dark	colored	cottons	may	release	a	
lot	of	dye.	Wash	them	separately.
•		 Use	only	dyes/color	changers	and	lime	 removers	suitable	for	machine	wash.	
Always	follow	the	instructions	on	the	
packaging.
•		 Wash	trousers	and	delicate	clothes	turned	 inside	out.
Correct load capacity
C	Please	follow	the	information	in	the	"Program	Selection	Table".	Washing	
results	will	degrade	when	the	machine	is	
overloaded.
Loading doorThe	door	locks	during	program	operation	and	the	
Door	Locked	Symbol	(Figure	3-13i)	lights	up.	The	
door	can	be	opened	when	the	symbol	fades	out.
Detergents and softenersDetergent Drawer
The	detergent	drawer	is	composed	of	three	
compartments:
The	detergent	dispenser	may	be	in	two	different	
types	according	to	the	model	of	your	machine.
–	(I)	for	prewash
–	(II)	for	main	wash
-	(III)	siphon	
–	(
)	for	softener
Detergent, softener and other cleaning 
agents
Add	detergent	and	softener	before	starting	the	
washing	program.
Never	open	the	detergent	dispenser	drawer	while	
the	washing	program	is	running!
When	using	a	program	without	pre-wash,	no	
detergent	should	be	put	into	the	pre-wash	
compartment	(Compartment	no.	I).
Detergent quantity
The	amount	of	washing	detergent	to	be	used	
depends	on	the	amount	of	laundry,	the	degree	of	
soiling	and	water	hardness.
•		 Do	not	use	amounts	exceeding	the	 quantities	recommended	on	the	package	
to	avoid	problems	of	excessive	foam,	
poor	rinsing,	financial	savings	and	finally,	
environmental	protection.
•		 Never	exceed	the	(>	max	
						

							5	-	EN
Turning the machine onPlug	in	your	 machine.	 Turn	the	tap	 on	completely.	
Check	if	the	hoses	are	connected	tightly.	Place	
the	laundry	in	the	machine.	Add	detergent	and	
softener.	Press	the	“On/Off”	button.
Program selectionSelect	the	appropriate	program	from	the	program	
table	and	the	following	washing	temperature	
table	according	to	type,	amount	and	degree	of	
soiling	of	the	laundry.	Select	the	desired	program	
with	the	program	selection	button.
C Programs	are	limited	with	the	highest	spin	
speed	appropriate	for	that	particular	type	
of	cloth.
Main programs Depending	on	the	type	of	textile,	the	following	
main	programs	are	available:
•Cottons
You	can	wash	your	durable	clothes	with	this	
program.	Your	laundry	will	be	washed	with	
vigorous	washing	movements	during	a	longer	
washing	cycle.	
•Synthetics/Mix
You	can	wash	your	less	durable	clothes	on	
this	program.	Lighter	washing	movements	 and	shorter	washing	cycle	is	used	compared	
to	“Cottons”	program.	It	is	recommended	for	
your	synthetic	clothes	(such	as	shirts,	blouses,	
synthetic/cotton	blended	garments,	etc.).	For	
curtains	and	lace,	the	“Synthetic(mix)40”	program	
with	pre-wash	and	anti-creasing	functions	
selected	is	recommended.
•Woolens
You	can	wash	your	machine-washable	woolen	
garments	on	this	program.	Wash	by	selecting	
the	proper	temperature	according	to	the	labels	
of	your	clothes.	It	is	recommended	to	use	
appropriate	detergents	for	woolens.	
Additional programs For	special	cases,	there	are	also	extra	programs	
available:
• Delicates
You	can	wash	your	delicate	clothes	on	this	
program.	It	has	more	sensitive	washing	
movements	and	does	not	make	intermediate	
spinning	compared	to	“Synthetic”	program.
• Shirt
You	can	use	this	program	to	wash	cottons	and	
synthetics	together.	There	is	no	need	to	sort	
them.
4  Selecting a Program and Operating Your Machine
1	 -	 Spin	Speed	Adjustment	Button
2	 -	 Time	Delaying	Button
3	 -	 Auxiliary	Function	Keys
4	 -	 Start/Pause/Cancel	Button
5	 -	 Program	Selection	Knob
6	 -	 Display
7	 -	 Child-proof	Lock	Indicator*
8	 -	 Program	Follow-up	Indicators	
9	 -	 On/Off	Button
*	According	to	your	machine’s	model
Start
Stop Start/Pause
Reset3 sec Voorwas
Lavage
Express
Wassen Rincage
Plus
Spoelen
Uitgestelde start Centrifugeren
Synthetisch
Katoen
Delicaat Wol Spoelen
Hemden
Délicat
Ouverture
de PorteEssorageRinçage
Lavage
Marche
Arrêt Lavage
Express
Essorage
M i n i   3 0
6 0 °
C h e m i s e
40
S p o r t   4 0
40°
Deur
openen WassenSpoelenCentrifugeren
S u p e r   4 0
30°
30°40°Rinçage PlusRinçage
40°
40°
30° 30°
60°60°
90°
Babycare
Synthétique
Laine Coton
Prélavage
Départ Différé
Annulation
3 sec.
Départ /Pause
5
1
3
9
87
4 2
6
Control panel
 
						

							6	-	EN
• Sport
This	program	is	suitable	for	clothes	that	
are	normally	worn	for	a	short	time	such	as	
sportswear.	It	is	used	to	quickly	wash	a	small	
amount	of	cotton/synthetic	blended	clothes.
• Super
This	program	washes	for	a	longer	period	at	40°C	
and	gives	the	same	result	as	the	“Cottons	60°C”	
program,	thus	it	saves	energy.	It	is	suitable	for	
clothes	for	which	you	cannot	use	the	“Cottons	
60°C”	program.	
• Mini
This	program	is	used	to	quickly	wash	(30	
minutes)	a	small	amount	of	lightly	soiled	cotton	
garments.
• Babycare
Increased	hygiene	is	provided	by	a	longer	
heating	period	and	an	additional	rinse	cycle.	It	is	
recommended	for	baby	clothes	and	clothes	worn	
by	allergic	people.
• Hand Wash
You	can	wash	your	woolen/delicate	clothes	that	
bear	“not	machine-	washable”	labels	for	which	
hand	wash	is	recommended	on	this	program.	
It	washes	the	laundry	with	very	tender	washing	
movements	without	damaging	your	clothes.
C Sort	the	laundry	according	to	type	
of	fabric,	color,	degree	of	soiling	and	
permissible	water	temperature	when	
choosing	a	program.
Special programsFor	specific	applications,	you	can	select	any	of	
the	following	programs:
• Rinse
This	program	is	used	when	you	want	to	rinse	or	
starch	separately.
• Spin and Pump
This	program	is	used	to	apply	an	additional	spin	
cycle	for	the	laundry	or	to	drain	the	water	in	the	
machine.
Before	starting	this	program,	select	the	desired	
spin	sped	and	press	“Start/Pause/Cancel”	
button.	Your	machine	drains	the	water	after	
spinning	at	the	set	spin	speed.
If	you	only	want	to	drain	the	water	without	
spinning	your	laundry,	select	“Spin	and	Pump”	
program,	and	then	select	no	spin	function	with	
spin	speed	selection	button.	Press	“Start/Pause/
Cancel”	button.
A	You	should	use	a	lower	spin	speed	for	delicate	laundries.
Spin Speed selectionWhenever	a	new	program	is	selected,	the	
maximum	spin	speed	of	the	selected	program	is	
displayed	on	the	spin	speed	indicator.
To	decrease	the	spin	speed,	press	the	“Spin”	
button.	Spin	speed	decreases	gradually.	Then,	
rinse	hold	and	no	spin	options	are	shown	
respectively.
Rinse	hold	is	shown	with	“
”	and	no	spin	is	
shown	with	“”	symbols.
If	you	do	not	want	to	unload	your	clothes	 immediately	after	the	program,	you	may	use	rinse	
hold	function	in	order	to	prevent	your	clothes	
become	wrinkled	in	anhydrous	conditions.	With	
this	function,	your	laundry	is	kept	in	the	final	
rinsing	
water.	If	you	 want	 to	spin	 your	 laundry	 that	
you	left	in	water:
-	Adjust	the	spin	speed.
-	Press	“Start/Pause/Cancel”	button.
Program	 resumes.	 Your	machine	 drains	the	water	
and	spins	your	laundry.
You	can	use	no	spin	function	in	order	to	drain	the	
water	without	spinning	at	the	end	of	the	program.
Downloaded From WashingMachine-Manual.com Manualë 
						

							7 - EN
Program and consumption table
•	:	Selectable
*	:	Automatically	selected,	not	cancellable.
**:	Energy	Label	programme	(EN	60456)
Water	and	power	consumption	and	programme	duration	may	differ	from	the	table	shown,	subject	to	
changes	in	water	pressure,	water	hardness	and	temperature,	ambient	temperature,	type	and	amount	
of	laundry,	selection	of	auxiliary	functions,	and	fluctuations	in	the	supply	voltage.
“Super	40”	programme	may	be	selected	instead	of	“Cotton	60*”	programme	during	winter	in	areas	
where	the	input	water	temperature	is	low	and/or	in	areas	with	low	supply	voltage.
C The	auxiliary	functions	in	the	table	may	differ	according	to	the	model	of	your	machine.
 Programme
Max. Load (kg)
Spin speed (rpm) 800-
1400
1600 rpm 1400 rpm 
(For A class spin  
efficiency)
Water Consumption (l)
Energy Consumption 
(kWh)
Prewash
Quick Wash
Rinse Plus
Anti-Creasing
Rinse Hold
No Heat
 Cottons906130 136492.18 ••••••
 Cottons 60**6135 139491.14 ••••••
 Cottons 406125 136490.66 ••••••
 Super 406161 171490.87 •
 Babycare 606164 174691.29 *• ••
 Sports 40375 75470.56 ••••••
 Synthetics 603103 103500.95 ••••••
 Synthetics(mix) 40396 96500.73 ••••••
 Shirts 40391 91480.34 •••• •
 Delicate 30265 65630.28 ••••
 Woollens 401.5 60 60560.27 •••
 Hand wash 30139 39410.15 •
 Mini 302.5 30 30380.25 •
 
						

							8 - EN
Auxiliary functionsAuxiliary Function Selection Buttons
Select	the	required	auxiliary	functions	before	
starting	the	program.
C Some	combinations	cannot	be	selected	
together.	(Ex.:	Pre-wash	and	Quick	Wash.
Warning	signal	on	the	selected	auxiliary	function	
will	light	up.
Auxiliary function selection
If	an	auxiliary	function	that	should	not	be	selected	
together	with	a	previously	selected	function	
is	chosen,	the	first	selected	function	will	be	
cancelled	and	the	last	auxiliary	function	selection	
will	remain	active.
(Ex.:	If	you	want	to	select	pre-wash	first	and	then	
quick	wash,	pre-wash	will	be	cancelled	and	quick	
wash	will	remain	active.
Auxiliary	function	that	is	not	compatible	with	the	
program	cannot	be	selected.	(see,	“Program	
Selection	Table”)
C Auxiliary	function	buttons	may	differ	
according	to	the	model	of	your	machine.
Pre-wash
A	pre-wash	is	only	worthwhile	for	heavily	soiled	
laundry.	Without	pre-wash	you	save	energy,	
water,	detergent	and	time.
C	Pre-wash	without	detergent	is	 recommended	for	lace	and	curtains.
Quick wash
This	function	can	be	used	for	“Cottons”	and	
“Synthetics”	programs.	It	decreases	the	washing	
times	for	lightly	soiled	laundries	and	also	the	
number	of	rinsing	steps.
Rinse Plus
With	this	function,	you	can	increase	the	number	
of	current	rinsing	steps.	Thus,	sensitive	skins’	risk	
of	being	affected	by	the	remainder	detergent	on	
the	clothes	will	be	decreased.
Anti-creasing
With	this	function,	drum	movement	will	be	
lessened	to	prevent	creasing	and	spinning	speed	
is	limited.	In	addition,	washing	is	carried	out	at	a	
higher	water	level.
C	Whenever	 you	select	 this	auxiliary	 function,	
load	your	machine	with	half	of	the	
maximum	laundry	specified	in	the	program	
table.
No Heat
If	you	wish	to	wash	your	clothes	in	cold	water,	
you	can	use	this	program.
Time displayThe	display	shows	the	time	remaining	for	the	
program	to	complete	while	a	program	is	running.	
Program	duration	may	differ	from	the	values	in	
the	consumption	table	subject	to	the	changes	
in	the	water	pressure,	water	hardness	and	
temperature,	ambient	temperature,	type	and	
amount	of	laundry,	auxiliary	functions	selected,	
and	changes	in	the	supply	voltage. Time delay
With	the	“Time	delay”	function	you	can	delay	the	
program	start	up	to	24	hours.	Time	delay	can	be	
set	with	steps	of	one	hour	for	the	first	three	hours	
and	with	steps	of	three	hours	for	the	remainder	
(1,	2,	3,	6,	9,	…24).
1.	Pres	“Time	Delay”	button	to	adjust	the	desired	
time.
2.	Press	“Start/Pause/Cancel”	button.	The	time	
delay	will	start	to	count	down.	
C	More	laundry	may	be	loaded	during	the	
time	delay	period.
Changing the delay time
If	you	want	to	change	the	time	during	the	
countdown:
1.	Press	“Start/Pause/Cancel”	button.
2.	Pres	“Time	Delay”	button	to	adjust	the	desired	
time	delay.
3.	Press	“Start/Pause/Cancel”	button.
Canceling the time delay
If	you	want	to	cancel	the	time	delay	countdown	
and	start	the	program:
1.	Press	“Start/Pause/Cancel”	button.
2.	Pres	“Time	Delay”	button	to	decrease	the	time	
delay.
3.	Press	“Start/Pause/Cancel”	button	to	start	the	
program.
Starting the Program1.	Press	“Start/Pause/Cancel”	button	to	start	the	
program.
2.	Program	follow-up	lamp	showing	the	startup	
of	the	program	will	light	up.
Progress of programProgress	of	a	running	program	is	shown	through	
the	program	follow-up	indicator.	At	the	beginning	
of	 every	 program	 step,	the	relevant	 indicator	 lamp	
will	light	up	and	light	of	the	completed	step	will	
turn	off.	The	symbol	that	is	lit	up	at	the	far	right	
of	the	series	of	symbols	indicates	the	step	that	is	
being	carried	out.
C	If	the	machine	is	not	spinning,	the	 program	may	be	in	rinse	hold	mode	or	
the	automatic	spin	correction	system	
has	been	activated	due	to	an	excessive	
unbalanced	distribution	of	laundry	in	the	
machine.
Changing the selections after the 
program has started
Turning	the	program	knob	while	the	program	is	in	
a	normal	flow	will	not	change	the	program.
Switching the machine to standby mode
Press	“Start/Pause/Cancel”	button	momentarily	
to	switch	your	machine	to	the	standby	mode.	
Auxiliary	functions	can	be	cancelled	or	selected	in	
accordance	with	the	step	the	program	is	at.	The	
Downloaded From WashingMachine-Manual.com Manualë 
						

							9	-	EN
door	can	be	opened	if	the	water	level	is	suitable.	
Laundry	may	be	added	/	taken	out	by	opening	
the	door.
Door lock
The	loading	door	can	not	be	opened	yet	due	to	
safety	reasons	while	the	“Ready”	lamp	is	flashing.	
The	loading	door	can	be	opened	once	the	
“Ready”	lamp	starts	lighting	up	continuously.
Child-proof lockYou	can	protect	the	appliance	from	being	
tampered	by	children	by	means	of	the	child-proof	
lock.	In	this	case,	no	change	can	be	made	in	the	
running	program.
The	machine	is	switched	to	child-lock	by	
pressing	the	1st	and	2nd	auxiliary	functions	for	3	
sec.	“C	on”	(Child	lock	is	activated)	label	appears	
on	the	screen.	The	same	symbol	will	also	be	
displayed	whenever	any	button	is	pressed	while	
the	machine	is	child-locked.
Child-proof	lock	lamp	on	the	program	follow-up	
indicator	will	light	up	when	the	child-proof	lock	is	
activated.
To	deactivate	the	child-proof	lock,	press	the	1st	
and	2nd	auxiliary	function	buttons	for	3	sec.	“C	
OFF”	(Child-proof	lock	is	deactivated)	symbol	
appears	on	the	screen.	Child-proof	lock	lamp	on	
the	program	follow-up	indicator	will	go	off	when	
the	child-proof	lock	is	deactivated.
Ending the program through 
canceling
“Start/Pause/Cancel”	button	is	pressed	for	3	
seconds	to	cancel	the	program.	“Ready”	warning	
lamp	flashes	during	canceling	and	“End”	will	
appear	on	the	display.
5 Maintenance and cleaning
Detergent DrawerRemove	any	powder	residue	buildup	in	the	
drawer.	To	do	this;
1.	 Press	the	dotted	 point	on	the	 siphon	 in	the	
softener	compartment	and	pull	towards	
you	until	the	compartment	is	removed	
from	the	machine.
C If	more	than	a	normal	amount	of	water	
and	softener	mixture	starts	to	gather	in	the	
softener	compartment,	the	siphon	must	
be	cleaned.
2.	 Wash	the	dispenser	drawer	and	the	 siphon	with	plenty	of	lukewarm	water	in	a	
washbasin.	
3.	 Replace	the	drawer	into	its	housing	after	 cleaning.		Check	if	the	siphon	is	in	its	
original	location.
Inlet water filtersThere	is	a	filter	at	the	end	of	each	water	intake	
valve	at	the	back	side	of	the	machine	and	also	at	
the	end	of	each	water	intake	hose	where	they	are	
connected	to	the	tap.	These	filters	prevent	the	
foreign	substances	and	dirt	in	the	water	to	enter	
into	the	machine.	Filters	should	be	cleaned	as	
they	get	dirty.
•	 Close	the	taps.
•	 Remove	the	nuts	of	the	water	intake	hoses	to	clean	the	surfaces	of	the	
filters	on	the	water	intake	valves	with	an	
appropriate	brush.
•	 If	the	filters	are	very	dirty,	you	can	pull	 them	out	by	means	of	pliers	and	clean	
them.
•	 Take	out	the	filters	on	the	flat	ends	of	 the	water	intake	hoses	together	with	
the	gaskets	and	clean	thoroughly	under	
streaming	water.
•	 Replace	the	gaskets	and	filters	carefully	to	 their	places	and	tighten	the	hose	nuts	by	
hand.
Downloaded From WashingMachine-Manual.com Manualë 
						

							10	-	EN
by	pulling	out	the	plug	at	the	end	of	the	
hose.	If	the	amount	of	water	to	be	drained	
off	is	greater	than	the	volume	of	the	
container,	replace	the	plug,	pour	the	water	
out,	then	resume	the	draining	process.
•		 After	draining	process	is	completed,	 replace	the	plug	into	the	end	of	the	hose	
and	fit	the	hose	back	into	its	place.
If	your	product	is	not	supplied	with	an	emergency	
drain	hose,	do	the	following	as	shown	in	the	
figure	below:
•		 Place	a	large	container	in	front	of	the	filter	 to	receive	water	flowing	from	the	filter.
•		 Loosen	pump	filter	(anticlockwise)	until	 water	starts	to	flow	out	of	it.	Direct	the	
flowing	water	into	the	container	you	have	
placed	in	front	of	the	filter.	You	can	use	a	
piece	of	cloth	to	absorb	any	spilled	water.
•		 When	there	is	no	water	left,	turn	the	pump	 filter	 until	it	is	 completely	 loose	and	remove	
it.
•		 Clean	any	residues	inside	the	filter	as	 well	as	fibers,	if	any,	around	the	propeller	
region.
•		 If	your	product	has	a	water	jet	feature,	be	 sure	to	fit	the	filter	into	its	housing	in	the	
pump.	Never	force	the	filter	while	replacing	
it	into	its	housing.	Fit	the	filter	fully	into	its	
housing;	otherwise,	water	may	leak	from	
the	filter	cap.
4-	Close	the	filter	cap.
Close	the	two-piece	filter	cap	of	your	product	by	
pushing	the	tab	on	it.
Close	the	one-piece	filter	cap	of	your	product	by	
fitting	the	tabs	on	the	bottom	into	their	positions	
and	pushing	the	upper	part	of	it.Draining any remaining water and 
cleaning the pump filter
Your	product	is	equipped	with	a	filter	system	
which	ensures	a	cleaner	water	discharge	that	
extends	pump	life	by	preventing	solid	items	such	
as	buttons,	coins	and	fabric	fibers	from	clogging	
the	pump	propeller	during	discharge	of	the	
washing	water.
•		 If	your	machine	fails	to	drain	the	water,	 the	pump	filter	may	be	clogged.	You	may	
have	to	clean	it	every	2	years	or	whenever	
it	is	plugged.	Water	must	be	drained	off	to	
clean	the	pump	filter.	
In	addition,	water	may	have	to	be	drained	off	
completely	in	the	following	cases:
•		 before	transporting	the	machine	(e.g.	 when	moving	house)
•		 when	there	is	the	danger	of	frost
In	order	to	clean	the	dirty	filter	and	discharge	the	
water;
1-	Unplug	the	machine	to	cut	off	the	supply	
power.
A	There	may	be	water	at	90°C	in	the	 machine.	Therefore,	the	filter	must	be	
cleaned	only	after	the	inside	water	is	
cooled	down	to	avoid	hazard	of	scalding.
2-	Open	the	filter	cap.	The	filter	cap	may	be	
composed	of	one	or	two	pieces	according	to	the	
model	of	your	machine.
If	it	is	composed	of	two	pieces,	press	the	tab	on	
the	filter	cap	downwards	and	pull	the	piece	out	
towards	yourself.
If	it	is	composed	of	one	piece,	hold	it	from	both	
sides	and	open	it	by	pulling	out.
3-	An	emergency	drain	hose	is	supplied	with	
some	of	our	models.	Others	are	not	supplied	with	
this	item.
If	your	product	is	supplied	with	an	emergency	
drain	hose,	do	the	following	as	shown	in	the	
figure	below:
•	 Pull	out	the	pump	outlet	hose	from	its	 housing.
•		 Place	a	large	container	at	the	end	of	the	 hose.	Drain	the	water	off	into	the	container	
Downloaded From WashingMachine-Manual.com Manualë