Barco Rlm R6+ Performer Owners Manual

4. Getting Started
No.Key nameDescription
10Lens controluse these buttons to obtain the desired ZOOM, SHIFT, FOCUS.
11VOLUsed as lens shift left - right.
12Picture controlsuse these buttons to obtain the desired picture analog level.
13DIGI ZOOMallows a digital Zoom of a part of the image
14FREEZEpress to freeze the projected image.
15PIPallows to activate the PICTURE IN PICTURE mode
16ENTERto confirm an adjustment or selection in the MENU.
On the local keypad and the RCU, the ENTER button additionally...

4. Getting Started
4.3 Lamp runtime
x
To generalize for the different projector types,xrefers here to the maximum run time of the lamp. The maximum run
time is given in the specifications.
Lamp runtime indication while running
Independently of the lamp mode, when the total runtime of an active lamp (lamp 1 for example) is (x -30) hours or more, a warning
message will be displayed.
WARNING !!!
LAMP 1: 1471 hrs
LAMP 2: 1400 hrs
Image 4-2
warning message
This warning message will be repeated at the next...

4. Getting Started
Switching to Standby. When the projector is running and you want to go to standby, press the standby key for
2 seconds until the message ’Saving data, please wait’ is displayed. Do not press any longer on the standby
key otherwise the projector will restart.
4.5 Switching off
How to switch off the projector?
1. Press firstStandby.
2. Let cool down the projector until the fans stop blowing, at least 15 min.
3. Switch off the projector with the power switch.
4.6 Temperature error DMD...

4. Getting Started
Hardwired Remote input
1. Plug one end of the remote cable in the connector on the bottom of the RCU. (image 4-5)
2. Plug the other end in the connector in the front panel of the projector labelled RC.
Specifications of the RC input
-U
in=9V
-I
max=80mA
• Internal IR receivers can be disabled:
omono jack : on plug in of the jack
ostereo jack : on plug in or using an external switch bringing the right channel (B) to ground level. (image 4-6)
Image 4-5
Hardwired remote control
1
2
ABC
D...

4. Getting Started
F
1F
2F
3F
4F
5
A
DJE
X
I
T
E
NT
ER
P
AU
SE
P
HA
SE T
EX
TS
HA
RP
NT
IN
TC
OL
ORB
RI
GH
TNC
ON
TRT
RE
BL
EB
AL
AN
CEB
AS
SV
OL 9
0
78
56
3
4
12
45° 45°
F
1F
2F
3F
4F
5
A
DJE
XI
T
E
NT
ER
P
AU
SE
P
HA
SE T
EX
TS
HA
RP
NT
IN
TC
OL
ORB
RI
GH
TNC
ON
TRT
RE
BL
EB
AL
AN
CEB
AS
SV
OL 9
0
78
56
3
4
12
IR Sensor on Front (A)
IR Sensor on Top (B)
F1F2F3F4F5
ADJEXIT
ENTER
PAUSE
PHASE TEXTSHARPNTINTCOLORBRIGHTNCONTRTREBLEBALANCEBASSVOL 90
78
56
34
12
IR Sensor (C)
Image 4-7
Remote control to IR...

4. Getting Started
Common address
Default address. Projector will always execute the command coming from a RCU programmed with that common
address.
Why a projector address ?
As more than one projector can be installed in a room, the separate projector should be separately addressable with an RCU or
computer. Therefor each projector has its own address.
Set up an individual Projector Address.
The set up of a projector address can be done via the software.
Projector controlling.
Every projector requires an...

4. Getting Started
Input Selection with alternative custom file (slot extension)
It is possible to select the same input but with another settings (another custom file will be loaded).
Howtodoit:
1. Press first0on the RCU. The Slot extension menu will be displayed.
2. Enter the two digits. First digit is custom file sequence and the second digit is the input. E.g. 33, the third custom file will be
loaded for source 3. If it does not exist, it will be created.
The same input can be loaded with 9 different...

4. Getting Started
To restart the image projection:
•PressPAUSEkey
4.10 Quick lens adjustment
Overview
• Lens Adjustment via Control Buttons on Projector
• Lens Adjustment via Menu Bar
• Direct Lens Adjustment (RCU)
4.10.1 Lens Adjustment via Control Buttons on Projector
How to enter the adjustment menu.
1. Press the control buttonLens(C).
The lens adjustment menu appears on the screen, requesting for ZOOM/FOCUS alignment.
2. Press button
(B) to toggle between ZOOM/FOCUS and Vert. Hor. SHIFT menu....

4. Getting Started
6. Press control button (D) to leave the lens adjustment menu.
A2
D
A
A1
1
2
...... Installation ......Lens adjustment
Projector address
......
Lens adjustment
Use 
↑ and ↓ for zoom
Use ← and → for focus
Press  for SHIFT mode
Press  or 
for test pattern
Lens adjustment
Use 
↑ and ↓ for vertical shift
Use ← and → for horizontal shift
Press  for ZOOM/FOCUS
Press  or 
for test pattern
B
C
3
Lens adjustment
Use ↑ and ↓ for zoom
Use ← and → for focus
Press  for SHIFT mode
Press  or 
for...

4. Getting Started
How to zoom ?
1. Press←or→on theDigital Zoomkey on the remote control to zoom the center of the image.
2. Use the↑,↓,→or←to pan the image. (image 4-15)
3. PressENTERto confirm.
Note:While in the digital zoom function, useBACKto return.
AB
CD
Image 4-15
Digital zoom
A Normal image
B Digital zoom out
C Digital zoom in
D Panning of the zoomed image
To return to the normal image, press MENU, go toTools, selectPiP selectand checkFull screen.
4.12 Quick Picture in Picture selection
Quick...