Barco Projector Cineversum 120 User Manual

7. Picture in Picture
7. PICTURE IN PICTURE
Overview
• Turning On/Off the Picture in Picture
• Selecting Input Source for PIP Window
• Function keys for Picture in Picture
7.1 Turning On/Off the Picture in Picture
How to turn On/Off the PIP
1. PressENTERto enter the adjustment menu. (image 7-1)
2. Select theAdvance Settingsmenu. (menu 7-1)
3. Select itemPiP Configurationby rotating the selection wheel on the Master or the up/down arrow keys on the Remote Control.
(menu 7-2)
4. Press the selection wheel...

7. Picture in Picture
7.2 Selecting Input Source for PIP Window
How to select input source for PIP window
The procedure below supposes an already selected input source (main image) and the PIP function set to ’Yes’.
1. Select the input source, remotely accessible with the digit keys on the Remote Control, you desire to be displayed into the PIP
window.
If no valid source is connected to the input of the selected input module, no PiP window appears.
If a valid source is connected to the input, the...

7. Picture in Picture
Image 7-3
PiP position
A F1, left corner top
B F2, left corner bottom
C F4, right corner top
D F5, right corner bottom
Image 7-4
PiP window enlarged
A PiP normal format
B Enlarged format
R5976667 CINEVERSUM SYSTEM 01102003
29 

7. Picture in Picture
Image 7-5
PiP swap
A Start image
B Swapped image after pressing F3
30
R5976667 CINEVERSUM SYSTEM 01102003 

8. Lens and Lamp manipulations
8. LENS AND LAMP MANIPULATIONS
Overview
• Lens adjustment
• Lamp
8.1 Lens adjustment
Lens
Your projector is equipped with a zoom lens which is remote controlled. Also the focus of the lens can be adjusted via remote control.
Shifting the image up - down or left - right is possible.
The installation menu can be password protected. Consult the installation manual for further instructions.
Overview
• Access to controls
• Focus adjustment
• Horizontal shift
• Vertical shift...

8. Lens and Lamp manipulations
Lens
Focus
Horizontal shift
Vertical shift
Zoom
Back
Menu 8-5
8.1.2 Focus adjustment
Steps to be taken
1. Use the up or down arrow keys to selectFocus.PressENTERto select. (menu 8-6)
A message will be displayed to use the arrow keys to control the lens.
2. Adjust with the arrow keys until sharp picture is obtained.
Lens
Focus
Horizontal shift
Vertical shift
Zoom
Back
Menu 8-6
8.1.3 Horizontal shift
Steps to be taken
1. Use the up or down arrow keys to selectHorizontal...

8. Lens and Lamp manipulations
A
BC
Image 8-1
Horizontal shift
A Normal image
B Image shifted to the right
C Image shifted to the left
8.1.4 Vertical shift
Steps to be taken
1. Use the up or down arrow keys to selectVertical shift.PressENTERto select. (menu 8-8)
A message will be displayed to use the arrow keys to control the lens.
2. Use the arrow keys to shift the image vertically. (image 8-2)
Lens
Focus
Horizontal shift
Vertical shift
Zoom
Back
Menu 8-8
ABC
Image 8-2
Ver ti cal shift
A Normal image
B...

8. Lens and Lamp manipulations
8.1.5 Zoom
Steps to be taken
1. Use the up or down arrow keys to selectZoom.PressENTERto select. (menu 8-9)
A message will be displayed to use the arrow keys to control the lens.
2. Use the arrow keys to zoom in or out until the desired screen size is obtained. (image 8-3)
Lens
Focus
Horizontal shift
Vertical shift
Zoom
Back
Menu 8-9
A
BC
Image 8-3
Zoom
8.2 Lamp
Lamp
Your projector can work with a single lamp or with a dual lamp. The ignited lamp or lamps can be boosted in...

8. Lens and Lamp manipulations
8.2.1 Access controls
Access to the control with the Remote control
1. Enter the adjustment menus by pressingENTERorADJ.
The general menu will be displayed. (menu 8-10)
2. Use the up or down arrow keys to selectImage Settingsand pressENTERto select.
If you shoot with your remote control directly to the projector, theImage Settingsmenu for the projector will be displayed.
(menu 8-11)
If you shoot with your remote control to the master, theImage Settingsmenu for the master...

8. Lens and Lamp manipulations
Switching on / off the lamps all time, reduces the lifetime of the lamps
8.2.3 Lamp power
Overview
The lamp can be powered in economic mode (200W) or normal mode (250W).
How to switch
1. Use the up or down arrow keys to selectLamp Power. (menu 8-15)
2. PressENTERto toggle betweenNormalandEconomic.
Note:Lamp life time will be extended in Economic mode.
Image Settings
Display
Brightness
Contrast
Gamma
Color Temperature
Primary [Projector]
Lamp mode [Single]
Lamp power...