Barco Projector Cineversum 120 User Manual
Here you can view all the pages of manual Barco Projector Cineversum 120 User Manual. The Barco manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 11
3. Overview User’s Controls 3. OVERVIEW USER’S CONTROLS Overview • Cine VERSUM Master • Cine VERSUM 120 • Remote Control • Remote Control operation 3.1 Cine VERSUM Master Front View The front side of theCine VERSUM Master is provided with the following controls: Image 3-1 Front side Cine VERSUM Master Controls function description Ref.FunctionDescription 1Infra Red Reception LED indicatorLights up when a valid Infra Red signal from the Remote Control has been captured. 2Infra Red ReceiverReception diode...
Page 12
3. Overview User’s Controls Image 3-2 Cine VERSUM 120 controls Controls function description Ref.FunctionDescription 1Main power switchButton pressed, switches the projector in the ’Standby’ mode. This mode is indicated by the standby LED which lights up repeatedly 2 times short on, 1 time long off. 2Infra Red ReceiverReception diode for the IR signals from the Remote Control. Allows switching On/Off (Standby) of the projector separately and controlling the Cine VERSUM Master. 3Standby LEDLights up...
Page 13
3. Overview User’s Controls 2 10 114 514 6 7 3 12 18 9 Image 3-3 Remote control Controls function description Ref.FunctionDescription 1Adjust buttonTo enter the adjustment menus or the leave the adjustment menus. For more explanation about the adjustment menus, consult the installation manual. 2Address buttonTo match the Remote Control with the unit that you are addressing (number between 0 and 9). 3Pause buttonTo blank the image in the digital link. 4Standby buttonTo power up/down the Cine VERSUM Master...
Page 14
3. Overview User’s Controls Stored sources The Cine VERSUM Master can be equipped with up to 8 digital and analog input modules. These modules are linked to your sources and can be selected with the touch of a button on the Remote Control. The table below allows you to note the stored source per input slot, digit button 1 to 8. Digit ButtonStored source 1 2 3 4 5 6 7 8 3.4 Remote Control operation Overview • General • Battery Insertion in the Remote Control • Visualization of commands 3.4.1 General How...
Page 15
3. Overview User’s Controls Image 3-4 Master control via 2-way communication SL/XL cable Backlighting When a button on the remote control is pressed, backlight is activated automatically. That allows the user to operate the remote control in a dark room. Backlight is turned off automatically a few seconds after the last button activation. If backlight and RC operation indicator lights up too long or continuously, batteries need to be replaced. Factory address setting of the modules The factory address...
Page 16
3. Overview User’s Controls 4. Insert two AA size batteries, making sure the polarities match the + and – marks inside the battery compartment (image 3-7). 5. Insert the lower tab of the battery cover in the gap at the bottom of the remote control, and press the cover until it clicks in place (image 3-7). Image 3-5 Battery cover unlock Image 3-6 Battery cover removal Image 3-7 Battery removal How to reinstall the address By removing the batteries, the address in the Remote Control will beset to 0. In...
Page 17
3. Overview User’s Controls Image 3-10 Message address display master 3.4.3 Visualization of commands How the commands are visualized When a button on the Remote Control or the dial knob on the Cine VERSUM Master is pressed, the command is visualized on the screen of the plasma display or of the projector and also on the graphical display of the Cine VERSUM Master. This can take the form of a menu, a message or a bar scale. Below an illustration of each item: Image 3-11 On-screenmainmenu Image 3-12 Main...
Page 19
4. Switching On/Off the Cine Versum System 4. SWITCHING ON/OFF THE CINE VERSUM SYSTEM Overview • Brief introduction • Upon first startup • Switching the system between OPERATION and STANDBY • Switching the system between STANDBY and ECONOMIC Standby • Switching the system OFF completely and BACK to Operation mode • Turning ON the system from total OFF mode 4.1 Brief introduction About the handled system in this manual The Cine VERSUM is a modular system that provides you the possibility to connect more...
Page 20
4. Switching On/Off the Cine Versum System Image 4-2 Cine VERSUM 120 Image 4-3 Cine VERSUM Master jog dial Image 4-4 Power up selection 4.3 Switching the system between OPERATION and STANDBY Overview • From OPERATION mode to STANDBY mode • From STANDBY mode to OPERATION mode 4.3.1 From OPERATION mode to STANDBY mode Using the Jog dial on the Cine VERSUM Master 1. Press the jog dial once to enter the main menu. (image 4-5) 2. Rotate the jog dial until “Shut down” in the menu is pointed to. (image 4-6) 3....