Barco Projector Cineversum 120 User Manual

							3. Overview User’s Controls
3. OVERVIEW USER’S CONTROLS
Overview
• Cine VERSUM Master
• Cine VERSUM 120
• Remote Control
• Remote Control operation
3.1 Cine VERSUM Master
Front View
The front side of theCine VERSUM Master is provided with the following controls:
Image 3-1
Front side Cine VERSUM Master
Controls function description
Ref.FunctionDescription
1Infra Red Reception LED indicatorLights up when a valid Infra Red signal from the Remote Control has
been captured.
2Infra Red ReceiverReception diode for the Infra Red signals sent by the Remote Control
when a key is pressed.
3Standby LEDBlinks when the Cine VERSUM Master has been powered down to
Standby or Economy Standby mode.
4Main power switch(see Switching On/Off the Cine Versum System, page 15)
5LCD DisplayThis display indicates the status of the Cine VERSUM Master and allows
you to navigate through the different menus.
6Selection and Confirmation dialThe knob allows to navigate through the different menus.
Table 3-1
3.2 Cine VERSUM 120
To p V i e w
The top side of the Cine VERSUM 120 is provided with the following controls:
R5976667 CINEVERSUM SYSTEM 01102003
7 
						

							3. Overview User’s Controls
Image 3-2
Cine VERSUM 120 controls
Controls function description
Ref.FunctionDescription
1Main power switchButton pressed, switches the projector in the ’Standby’ mode. This mode
is indicated by the standby LED which lights up repeatedly 2 times short
on, 1 time long off.
2Infra Red ReceiverReception diode for the IR signals from the Remote Control. Allows
switching On/Off (Standby) of the projector separately and controlling
the Cine VERSUM Master.
3Standby LEDLights up continuously: projector in the operation mode.
Lights up repeatedly 2 times short on, 1 time long off: projector in the
standby mode
Blinks fast: projector in the cooling down mode after switching off
(duration 1 min.).
Lights up repeatedly 1 time long, 1 time short: projector has been started
up in the cooling down mode, waiting for lamp ignition.
4Not used
5Infra Red Reception LED indicatorLights up when a valid IR signal from the Remote Control has been
captured.
Table 3-2
3.3 Remote Control
To p s i d e
The Infra Red Remote Control buttons support the following functionality:
8
R5976667 CINEVERSUM SYSTEM 01102003 
						

							3. Overview User’s Controls
2
10
114
514
6
7
3
12
18
9
Image 3-3
Remote control
Controls function description
Ref.FunctionDescription
1Adjust buttonTo enter the adjustment menus or the leave the adjustment menus. For more
explanation about the adjustment menus, consult the installation manual.
2Address buttonTo match the Remote Control with the unit that you are addressing (number between
0 and 9).
3Pause buttonTo blank the image in the digital link.
4Standby buttonTo power up/down the Cine VERSUM Master and the displays in the link.
5Digit buttonsAllows to directly select sources.
6RC operation indicationLights up when a button on the remote control is pressed (Visual indication of remote
control operation – Battery check).
7Function keysThe function keys are used in picture in picture (PIP) to position the PIP image.
8EXIT buttonTo go up one step in the menu structure.
9ENTER buttonTo enter the adjustment menus or to confirm an adjustment with the adjustment
menus.
10TEXTWhen text is on, press TEXT to switch off OSD display. Press TEXT again, OSD
appears as defined in the OSD configuration window.
11FREEZEPress to freeze the image
12* ButtonAspect ratio toggle button for the actual image
13Picture controlsAllow to optimize the picture reproduction
Table 3-3
R5976667 CINEVERSUM SYSTEM 011020039 
						

							3. Overview User’s Controls
Stored sources
The Cine VERSUM Master can be equipped with up to 8 digital and analog input modules. These modules are linked to your sources
and can be selected with the touch of a button on the Remote Control.
The table below allows you to note the stored source per input slot, digit button 1 to 8.
Digit ButtonStored source
1
2
3
4
5
6
7
8
3.4 Remote Control operation
Overview
• General
• Battery Insertion in the Remote Control
• Visualization of commands
3.4.1 General
How to use
The Remote Control allows you to control your Cine VERSUM Master, even when it is built into a cabinet. Indeed, the SL/XL cable
allows for 2–way communication. This means you can point the Remote Control to a display unit and still change the settings of the
Cine VERSUM Master.
10
R5976667 CINEVERSUM SYSTEM 01102003 
						

							3. Overview User’s Controls
Image 3-4
Master control via 2-way communication SL/XL cable
Backlighting
When a button on the remote control is pressed, backlight is activated automatically. That allows the user to operate the remote
control in a dark room. Backlight is turned off automatically a few seconds after the last button activation.
If backlight and RC operation indicator lights up too long or continuously, batteries need to be replaced.
Factory address setting of the modules
The factory address setting of the modules is as follows:
ModuleIndividual AddressCommon Address
Cine VERSUM 120address no common address
Cine VERSUM Masteraddress common address 
Common address: is a fixed address, stored in the module. The module will execute the commands sent by
a Remote Control, programmed with the common address .
3.4.2
Battery Insertion in the Remote Control
Where to find the batteries
The batteries are not placed in the remote control to avoid remote control operation in its package, resulting in a shorter battery life
time.
How to install the batteries
1. Push the cover tab (A) with the fingernail a little backwards and pull upwards the cover top (B). (image 3-5)
2. Slide the cover forwards to remove. (image 3-6)
3. Push the battery body towards the spring and lift it up to remove. (image 3-7)
R5976667 CINEVERSUM SYSTEM 01102003
11 
						

							3. Overview User’s Controls
4. Insert two AA size batteries, making sure the polarities match the + and – marks inside the battery compartment (image 3-7).
5. Insert the lower tab of the battery cover in the gap at the bottom of the remote control, and press the cover until it clicks in place
(image 3-7).
Image 3-5
Battery cover unlock
Image 3-6
Battery cover removal
Image 3-7
Battery removal
How to reinstall the address
By removing the batteries, the address in the Remote Control will beset to 0. In case the different modules are controlled separately
(own address), the respective address of the module you desire to control has to be set. To reinstall an address, follow procedure
below:
1. Point the Remote Control to the module of which you want to know the address and press the address button (use a pencil).
(image 3-8)
On the screen appears a message box (image 3-9) indicating the address number. In the graphical display of the Cine VERSUM
Master appears the same message (image 3-10).
2. To adapt the address in the Remote Control, cover the IR transmitting diodes and press the address button once, followed within
the 5 seconds by pressing the corresponding digit button, 1 to 8.
Image 3-8Image 3-9
Message address on-screen
12R5976667 CINEVERSUM SYSTEM 01102003 
						

							3. Overview User’s Controls
Image 3-10
Message address display master
3.4.3 Visualization of commands
How the commands are visualized
When a button on the Remote Control or the dial knob on the Cine VERSUM Master is pressed, the command is visualized on the
screen of the plasma display or of the projector and also on the graphical display of the Cine VERSUM Master. This can take the
form of a menu, a message or a bar scale. Below an illustration of each item:
Image 3-11
On-screenmainmenu
Image 3-12
Main menu on Master display
Image 3-13
On-screen message
Image 3-14
Message on Master display
Image 3-15
On-screen bar scale
Image 3-16
Bar scale on Master display
R5976667 CINEVERSUM SYSTEM 0110200313 
						

							3. Overview User’s Controls
14R5976667 CINEVERSUM SYSTEM 01102003 
						

							4. Switching On/Off the Cine Versum System
4. SWITCHING ON/OFF THE CINE VERSUM SYSTEM
Overview
• Brief introduction
• Upon first startup
• Switching the system between OPERATION and STANDBY
• Switching the system between STANDBY and ECONOMIC Standby
• Switching the system OFF completely and BACK to Operation mode
• Turning ON the system from total OFF mode
4.1 Brief introduction
About the handled system in this manual
The Cine VERSUM is a modular system that provides you the possibility to connect more than one display device to the Cine
VERSUM Master.
In this owner’s manual, we only discuss the most common case : one Master linked to one Projector. For info on the more complex
systems, please review the installation manual.
This is the chapter’s structure:
• Upon first startup
• Switching the system between OPERATION mode and STANDBY
• Switching the system between STANDBY and ECONOMIC STANDBY
• Switching the system OFF completely and BACK TO OPERATION mode.
4.2 Upon first startup
Required steps
There are two steps upon first startup:
1. Press the power switch (A) on the Cine VERSUM Master. (image 4-1)
The Cine VERSUM Master goes from OFF to STANDBY, visualized by blinking of the standby indicator
(B).
2. Press the power switch (A) on the Cine VERSUM 120. (image 4-2)
The Cine VERSUM 120 goes from OFF to STANDBY, visualized by blinking of the standby indicator
(B).
3. Select “Power up” in the menu on the Cine VERSUM Master, using the jog dial. (image 4-3, image 4-4)
The Cine VERSUM Master and the Cine VERSUM 120 go from STANDBY to operation, visualized by lighting up of the proper
standby indicator
(B).
Image 4-1
Cine VERSUM Master
R5976667 CINEVERSUM SYSTEM 0110200315 
						

							4. Switching On/Off the Cine Versum System
Image 4-2
Cine VERSUM 120
Image 4-3
Cine VERSUM Master jog dial
Image 4-4
Power up selection
4.3 Switching the system between OPERATION and STANDBY
Overview
• From OPERATION mode to STANDBY mode
• From STANDBY mode to OPERATION mode
4.3.1 From OPERATION mode to STANDBY mode
Using the Jog dial on the Cine VERSUM Master
1. Press the jog dial once to enter the main menu. (image 4-5)
2. Rotate the jog dial until “Shut down” in the menu is pointed to. (image 4-6)
3. Press jog dial to activate the Shutdown selection.
The Cine VERSUM Master and the Cine VERSUM 120 go from OPERATION to STANDBY. During the power down process, a
power down message appears on-screen and on the Master display. At the end, the Master displays the enter menu screen.
(image 4-7, image 4-8)
16
R5976667 CINEVERSUM SYSTEM 01102003