Barco Projector Cineversum 110 Quickstart Manual

13. Display Setup
Image 13-10
Status bar position
This is useful in applications where the bottom image content is not displayed (e.g. due to blanking).
How to center the menu ?
1. PressMENUto activate the menu bar.
2. Press→to select theDisplay setupitem. (image 13-11)
3. Press↓to pull down theDisplay setupmenu.
4. Use↑or↓to selectStatus bar position.
5. PressENTER.
6. Use↑or↓to position the status bar
Image 13-11
13.7 Sliderbox position
What can be done ?
The sliderbox can be displayed anywhere on the...

13. Display Setup
Image 13-12
Sliderbox position
X position :   619   Y position :   618
Press  for fine adjustment
Image 13-13
There is a coarse and a fine adjustment of the position, use ENTER (when sliderbox is displayed) to switch
between the two.
13.8 Auto Image Setup
What can be done ?
Auto image allows to detect automatically the characteristics of the source (total pixels per line,...) and uses this information to adapt
the image to the DLP panels.
Auto image can adapt the image based on...

13. Display Setup
Image 13-14
Autoimage setup
Total pixels/lines
Start pixel/line
Phase
Contrast/brightness
Image 13-15
How to perform Auto Image ?
1. pressAuto Imageon the RCU
A text box showing a progress bar is displayed.
During the AUTO IMAGE measuring process the data source disappears temporarily (logo is displayed if back-
ground is set to logo)
Autoimage setup
Total pixels/lines
Start pixel/line
Phase
Contrast/brightness
Image 13-16
R5976697 CINEVERSUM™ 110 12/05/2004119 

13. Display Setup
120R5976697 CINEVERSUM™ 110 12/05/2004 

14. Installation menu
14. INSTALLATION MENU
Overview
• Lens adjustments
• Projector address
• Orientation
• Language
• Quick access keys
• RS232 baudrate
• Automatic startup
• Security
14.1 Lens adjustments
What can be done ?
Motorized lenses can be adjusted in the installation menuor via the dedicated keys on the remote (see chapter “Getting Started”,
“Quick lens adjustment”).
The following parameters can be adjusted:
•Zoom
• Focus
• Shift (also for non motorized lenses)
How to Zoom/focus or shift ?
1....

14. Installation menu
Image 14-1
Lens adjustment
Use 
↑ and ↓ for zoom
Use 
← and → for focus
Press  for SHIFT mode
Press  or 
for test pattern
Image 14-2
Lens adjustment
Use 
↑ and ↓ for vertical shift
Use 
← and → for horizontal shift
Press  for ZOOM/FOCUS
Press  or 
for test pattern
Image 14-3
14.2 Projector address
What can be done ?
In some cases the projector address must be changed, for example if an unique RCU is used to control 2 or more projectors in a
room.
The projector address setting on the...

14. Installation menu
Image 14-4
Projector addresses
Projector address
Common RC5 address5
1
Image 14-5
Projector addresses
Projector address
Common RC5 address
1005
Image 14-6
How to change the common address ?
1. PressMENUto activate the menu bar.
2. Press→to select theInstallation. (image 14-7)
3. Press↓to pull downtheInstallationmenu
4. Use↑or↓to selectProjector address
5. PressENTER
A dialog box appears on the screen. Use the↑to scroll to Common RC5 address. (image 14-8)
6. PressENTERto go to the...

14. Installation menu
14.3 Orientation
Projector orientations
Depending on how the projector is oriented, the projector’s internal settings have to be adapted. See also Chapter “Installation”,
“Orientation”.
How to change the orientation ?
1. PressMENUto activate the menu bar.
2. Press→to select theInstallationitem. (image 14-10)
3. Press↓to pull down theInstallationmenu.
4. Use↑or↓to selectOrientation.
5. Press→to pull down the menu.
6. Use↓or↑to select the desired orientation.
7. PressENTERto confirm....

14. Installation menu
Image 14-11
14.5 Quick access keys
What can be done ?
The 3 function keys on top of the RCU (F1, F2 and F3) can be associated with a particular item in one of the menus.
Each function which is not password protected can be associated to a function key.
How to get an overview of the quick access keys ?
1. PressMENUto activate the menu bar.
2. Press→to select theInstallation. (image 14-12)
3. Press↓to pull down theInstallationmenu.
4. Use↑or↓to selectQuick access keys.
5. PressENTER....

14. Installation menu
14.6 RS232 baudrate
How to change the baudrate?
1. PressMENUto activate the menu bar.
2. Press→to select theInstallationitem. (image 14-14)
3. Press↓to pull down theInstallationmenu.
4. Use↑or↓to selectRS232 baudrate
5. Press→to pull down the menu.
6. Use↓or↑to select the desired baudrate.
7. PressENTERto confirm.
Image 14-14
14.7 Automatic startup
What can be done ?
The automatic startup allows immediate restart of the projector after a power failure (breakdown), i.e. without...