Bang & Olufsen Beovision 7 40 55 Television User Manual

							71
System modulator 
If you have an audio setup, such as a 
BeoLink Active/Passive, and you choose 
to set up a non-linkable television in the  same room, you must set the sys  
tem 
modulator to ON. The factory setting is 
AUTO, which must be used if you are using 
a linkable Bang & Olufsen television. 
To switch on the system modulator … >  Bring up the T V SETUP menu and highlight 
OPTIONS. 
>  Press the centre button to bring up the 
OPTIONS menu and highlight 
CONNECTIONS. 
>  Press the centre button to bring up the 
CONNECTIONS menu, and highlight LINK. 
>  Press the centre button to bring up the 
LINK menu and highlight MODUL ATOR. 
>  Use the navigation button left or right to 
reveal ON. 
>  Press the centre button to store the 
setting, or …
>  … press and hold BACK to exit all menus 
without storing.  >> Distribute sound and picture with BeoLink
If, for example, a T V channel in your  area is broadcasted on the same channel 
as the factory setting for the BeoLink  system; channel 66, you must tune the 
system modulator to an unoccupied 
channel. When you change the link 
channel in the main room television, 
make sure that the link channel in the 
link room television corresponds to it. 
To change the link channel … >  Bring up the T V SETUP menu and highlight 
OPTIONS. 
>  Press the centre button to bring up the 
OPTIONS menu and highlight 
CONNECTIONS. 
>  Press the centre button to bring up the 
CONNECTIONS menu, and highlight LINK. 
>  Press the centre button to bring up the 
LINK menu and highlight CHANNEL. 
>  Use the navigation button left or right to 
find an unused channel . 
>  Press the centre button to store the 
setting, or …
>  … press and hold BACK to exit all menus 
without storing.  The LINK menu. 
When tuning in the link channel in the link room, a test image is shown. FINE TUNE is only available in link room/Option 4 setups.
Link channel 
LINK 
CHANNEL  66
MODUL ATOR  AUTO 
						

							‘Zone XX’
(Option 6)
72
If you have BeoLink installed in 
your home and you choose to  place your television in a link 
room, you can operate all  connected systems through the 
television. 
You must follow the procedure 
described below when you connect your television for use in a link room:
1  Connect the link room television to 
the mains 
2  Using your remote control, 
program the link room television 
to the correct Option 
3  Disconnect the link room television 
from the mains 
4  Make the necessary connections 
5  Reconnect the link room television 
to the mains. 
Your television in a link room 
For your entire system to function properly, it is essential that the 
television in the link room is set to the  correct Option before you connect it to 
the television in the main room! 
With Beo6 …  >  Place yourself in front of the link room 
television. 
>  While holding the • button, press the 
centre button to bring up the SETUP 
menu on Beo6. 
>  Let go of both buttons. 
>  Press Option Pgm to bring up the Option 
Programming display on Beo6. 
>  Press the button that matches the zone in 
which the television is placed. 
With Beo4 …  >  While holding the • button, press LIST on 
Beo4. 
>  Let go of both buttons. 
>  Use the navigation button up or down to 
bring up OPTION? in the Beo4 display 
and press the centre button. 
>  Use the navigation button up or down to 
bring up V.OPT in the Beo4 display and 
press 6 *.  *If you connect the television for use in a link 
room where other link systems are already connected, such as speakers, you must set 
the television to Option 5 instead. 
Option setting 
Link room Main room  
						

							73
When you are in the link room, you can operate all connected systems with the remote control. 
Use sources present only in one of the  rooms … 
>  Press the button for the source you wish 
to use, for example R ADIO . 
>  Operate the selected source as usual. 
Use a main room source – source type  present in both rooms … 
>  Press Link to bring up a source display. 
(Beo4: Press LIST and use the navigation  button up or down to bring up LINK in 
the Beo4 display). 
>  Press the button for the source you wish 
to use, for example T V . 
>  Operate the source as usual. 
Use a link room source – source type  present in both rooms … 
>  Press the button for the source you wish 
to use, for example T V . 
>  Operate the source as usual.  Listen to stereo sound in your link 
room … 
Usually sound distributed from a main room  video source, such as a set-top box, to the link room is transmitted in mono. However, 
you can select stereo sound: 
>  Press T V to switch on the television. 
>  Press AV to bring up a source display. 
(Beo4: Press LIST and use the navigation  button up or down to bring up AV in the 
Beo4 display). 
>  Press, for example DT V , to activate a 
source connected to the main room 
television, such as a set-top box. 
While using this function, distribution of  other main room sources to other link room 
systems is not possible. 
Sound in the main room and the link room is  sometimes not synchronised. In some cases, 
you can synchronise the sound by selecting a  source, then pressing AV and selecting the 
source again. (Beo4: Select a source, then  press LIST and use the navigation button up 
or down to bring up AV in the Beo4 display 
and then select the source again). 
If you switch to a different source in the  main room, the sound volume may change. 
Link room operation 
>> Your television in a link room
Link room 
Main room  
						

							BeoVision 7
Option 4
T V
L I S T
L I N K T V
BeoV ision 7
Zone ‘A ’
Z o n e ‘ B ’
T V
Z o n e
 ‘ A’
T V
BeoV ision 7
Zone ‘B’
74
Two televisions in the same room 
If you have placed your television 
in a room where you already  have a Bang & Olufsen television, 
and commands from your  remote control can be received by both televisions, you must change the Option setting of the 
television. This prevents  simultaneous activation of both 
televisions. 
When you Option program the 
television, disconnect the television  you do not want to program from 
the mains. This ensures that only the 
television, you want to program,  receives the Option programming. 
One remote control for both televisions 
For your television to function properly, 
it is essential that the television is set to 
the correct Option, see page 72 for  information on Option programming.  
If you have a Beo4, you must set your 
television to Option 4, and if you have a  Beo6, you must set the television to the correct zone*. 
Beo4 – Operate your television in 
Option 4 …  Normally, you can activate a source, such as T V, simply by pressing the relevant  source button on your remote control. 
However, when you set your television 
to Option 4, you must do the following,  if you have a Beo4: 
>  Press LIST and use the navigation button 
up or down to bring up LINK in the Beo4 display. 
>  Press a source button, such as T V . Beo6 operation. 
*NOTE! For information about choice of zone,  contact your Bang & Olufsen retailer. 
Beo4 operation.