Avaya Partner Advanced Communications System 1600 Dsl Module User Guide

							Avaya, Inc. - 110 - PARTNER ACS 1600 DSL module User Guide
6. Select the encapsulation you want to configure.
If you select RFC 2364 (PPPoATM with LLC
Encapsulation) or RFC 2364 (PPPoATM using VC
Muxing), follow the on-screen messages to set the PPP
authorization type.  Once complete, continue with step 8.
The ATM Service Category Configuration submenu
displays.
*****************************************
* ATM Service Category Configuration *
*****************************************
1. CBR
2. UBR
7. Do one of the following:
Select CBR for high priority data.
Select UBR for low priority data.
Follow the on-screen messages to set the Peak Cell Rate
(PCR) value.
You must restart the PARTNER ACS 1600 DSL module
for any changes to take effect.  For more information on
restarting the PARTNER ACS 1600 DSL module, see the
“Getting started” chapter.
Modifying a PVC
To modify a PVC
1. On the Main Menu, select Configure WAN, and then type
the slot number of the WAN interface that you want to
configure.
The WAN Configuration Menu displays.
2. Select Configure PVCs.
The ATM PVC Config Menu displays.
*****************************************
* ATM PVC Config Menu *
*****************************************
1. Add New PVC
2. Modify Existing PVC
3. Delete PVC
4. Show Current PVCs
3. Select Modify Existing PVC.
4. Type the port number to modify, and then press ENTER.
5. Type a VPI between 0-255 (default = 0), and then press
ENTER. 
						

							Avaya, Inc. - 111 - PARTNER ACS 1600 DSL module User Guide
6. Type a VCI between 32 – 65535 (default = 38 – data or 39
– voice), and then press ENTER.
The ATM Encapsulation Configuration submenu
displays.
*****************************************
* ATM Encapsulation Configuration *
*****************************************
Current Encapsulation : NONE
1. AAL5 (None)
2. AAL0 (None)
3. Proprietary Voice
4. RFC 1483 (using VC Muxing)
5. RFC 1483 (with LLC Encapsulation)
6. RFC 2364 (PPPoATM with LLC
Encapsulation)
7. RFC 2364 (PPPoATM using VC Muxing)
7. Select the encapsulation you want to configure.
If you select RFC 2364 (PPPoATM with LLC
Encapsulation) or RFC 2364 (PPPoATM using VC
Muxing), follow the on-screen messages to set the PPP
authorization type.  Once complete, continue with step 8.
The ATM Service Category Configuration submenu
displays.
*****************************************
* ATM Service Category Configuration *
*****************************************
1. CBR
2. UBR
8. Do one of the following:
Select CBR for high priority data.
Select UBR for low priority data.
9. Follow the on-screen messages to set the Peak Cell Rate
(PCR) value.
You must restart the PARTNER ACS 1600 DSL module
for any changes to take effect.  For more information on
restarting the PARTNER ACS 1600 DSL module, see the
“Getting started” chapter. 
						

							Avaya, Inc. - 112 - PARTNER ACS 1600 DSL module User Guide
Deleting a PVC
To delete a PVC:
1. On the Main Menu, select Configure WAN, and then type
the slot number of the WAN interface that you want to
configure.
The WAN Configuration Menu displays.
2. Select Configure PVCs.
The ATM PVC Config Menu displays.
*****************************************
* ATM PVC Config Menu *
*****************************************
1. Add New PVC
2. Modify Existing PVC
3. Delete PVC
4. Show Current PVCs
3. Select Delete PVC.
4. Type the port number to delete, and then press ENTER.
5. Do one of the following:
To delete the PVC, type y.
To cancel the deletion, type n.
You must restart the PARTNER ACS 1600 DSL module
for any changes to take effect.  For more information on
restarting the PARTNER ACS 1600 DSL module, see the
“Getting started” chapter.
Configuring
ATM options
The PARTNER ACS 1600 DSL module contains commands
that allow you to configure or display the following ATM
options:
Payload Scrambling
F4 OAM VPI
F4 OAM Type
F4 OAM Configuration
OAM Loopback
Empty Cells 
						

							Avaya, Inc. - 113 - PARTNER ACS 1600 DSL module User Guide
Configuring Payload Scrambling
You must enable payload scrambling (default = disabled) for
the PARTNER ACS 1600 DSL module to “talk” to a DSLAM
that uses payload scrambling.
To enable payload scrambling:
1. On the Main Menu, select Configure WAN, and then type
the slot number of the WAN interface that you want to
configure.
The WAN Configuration Menu displays.
2. Select Configure ATM Options.
The ATM Configuration Menu displays.
*****************************************
* ATM Configuration Menu *
*****************************************
1. Configure Payload Scrambling
2. Configure F4 OAM VPI
3. Configure F4 OAM Type
4. Display F4 OAM Configuration
5. Send OAM Loopback
6. Configure EmptyCells
3. Select Configure Payload Scrambling, and then do one
of the following:
To enable payload scrambling, type E.
To disable payload scrambling, type D.
You must restart the PARTNER ACS 1600 DSL module
for any changes to take effect.  For more information on
restarting the PARTNER ACS 1600 DSL module, see the
“Getting started” chapter.
Configuring the F4 OAM Cell
To configure the F4 OAM Cell
1. On the Main Menu, select Configure WAN, and then type
the slot number of the WAN interface that you want to
configure.
The WAN Configuration Menu displays. 
						

							Avaya, Inc. - 114 - PARTNER ACS 1600 DSL module User Guide
2. Select Configure ATM Options.
The ATM Configuration Menu displays.
*****************************************
* ATM Configuration Menu *
*****************************************
1. Configure Payload Scrambling
2. Configure F4 OAM VPI
3. Configure F4 OAM Type
4. Display F4 OAM Configuration
5. Send OAM Loopback
6. Configure EmptyCells
3. Select Configure F4 OAM VPI, and then type the VPI.
This value must match one of the WAN PVCS.  For more
information, see the “Configuring PVCs” section earlier in
this chapter.
The ATM Configuration Menu redisplays.
4. Select Configure F4 OAM Type.
The F4 OAM Type Configuration Menu displays.
*******************************************
* F4 OAM Type Configuration Menu *
*******************************************
0. None
4. F4 End to end OAM
5. Select your choice.
You must restart the PARTNER ACS 1600 DSL module
for any changes to take effect.  For more information on
restarting the PARTNER ACS 1600 DSL module, see the
“Getting started” chapter.
Sending OAM Loopback
To send an OAM Loopback:
1. On the Main Menu, select Configure WAN, and then type
the slot number of the WAN interface that you want to
configure.
The WAN Configuration Menu displays. 
						

							Avaya, Inc. - 115 - PARTNER ACS 1600 DSL module User Guide
2. Select Configure ATM Options.
The ATM Configuration Menu displays.
*****************************************
* ATM Configuration Menu *
*****************************************
1. Configure Payload Scrambling
2. Configure F4 OAM VPI
3. Configure F4 OAM Type
4. Display F4 OAM Configuration
5. Send OAM Loopback
6. Configure EmptyCells
3. Select Send OAM Loopback.
A list of all configured F4 OAM ports and its VPI value
displays.
4. Select the port on which to send the OAM Loopback, and
then press ENTER.
Configuring Empty Cells
To configure empty cells:
1. On the Main Menu, select Configure WAN, and then type
the slot number of the WAN interface that you want to
configure.
The WAN Configuration Menu displays.
2. Select Configure ATM Options.
The ATM Configuration Menu displays.
*****************************************
* ATM Configuration Menu *
*****************************************
1. Configure Payload Scrambling
2. Configure F4 OAM VPI
3. Configure F4 OAM Type
4. Display F4 OAM Configuration
5. Send OAM Loopback
6. Configure EmptyCells
3. Select Configure EmptyCells.
The following instructions display on-screen:
Empty Cells are currently IDLE 
						

							Avaya, Inc. - 116 - PARTNER ACS 1600 DSL module User Guide
Enter 1 for IDLE cells or 2 for UNASSIGNED
cells:
4. Select your choice.
You must restart the PARTNER ACS 1600 DSL module
for any changes to take effect.  For more information on
restarting the PARTNER ACS 1600 DSL module, see the
“Getting started” chapter.
Configuring
Frame Relay
DLCIs
The PARTNER ACS 1600 DSL module contains commands
that allow you to configure Frame Relay DLCIs:
Add New DLCI
Modify Existing DLCI
Delete DLCI
Show Current DLCIs
You can configure up to 24 DLCIs on the PARTNER ACS
1600 DSL module.
Adding a DLCI
To add a DLCI:
1. On the Main Menu, select Configure WAN, and then type
the slot number of the WAN interface that you want to
configure.
The WAN Configuration Menu displays.
2. Select Configure DLCIs.
The FR DLCI Config Menu displays.
*****************************************
* FR DLCI Config Menu *
*****************************************
1. Add New DLCI
2. Modify Existing DLCI
3. Delete DLCI
4. Show Current DLCIs
3. Select Add New DLCI. 
						

							Avaya, Inc. - 117 - PARTNER ACS 1600 DSL module User Guide
4. Type a DLCI value between 16-1023 (defaults = 32 – data
and 33 – voice), and then press ENTER.
The FR Encapsulation Configuration submenu displays.
*****************************************
* FR Encapsulation Configuration *
*****************************************
Current Encapsulation : None
1. RAW (No Encapsulation)
2. Proprietary Voice DLCI
3. RFC 1490
4. ATM RFC 1483 (Tunneling)
5. Select the encapsulation method to use.
The FR DLCI Options submenu displays.
*****************************************
* FR DLCI Options *
*****************************************
1. Configure Transmit CIR
2. Configure Receive CIR
3. Configure FRF.12 Fragmentation
6. Do one of the following:
Select Configure Transmit CIR or Configure
Receive CIR, and then follow the on-screen
messages to set:
Committed burst size (Bc)
Circuit throughput
Excess burst size (Be)
Select Configure FRF .12 Fragmentation, and
then follow the on-screen messages to:
Enable/Disable End-to-End FRF .12
Set Fragment Size
You must restart the PARTNER ACS 1600 DSL module
for any changes to take effect.  For more information on
restarting the PARTNER ACS 1600 DSL module, see the
“Getting started” chapter. 
						

							Avaya, Inc. - 118 - PARTNER ACS 1600 DSL module User Guide
Modifying a DLCI
To modify a DLCI:
1. On the Main Menu, select Configure WAN, and then type
the slot number of the WAN interface that you want to
configure.
The WAN Configuration Menu displays.
2. Select Configure DLCIs.
The FR DLCI Config Menu displays.
*****************************************
* FR DLCI Config Menu *
*****************************************
1. Add New DLCI
2. Modify Existing DLCI
3. Delete DLCI
4. Show Current DLCIs
3. Select Modify Existing DLCI.
4. Type the port number to change, and then press ENTER.
5. Type the DLCI value, and then press ENTER.
The FR Encapsulation Configuration submenu displays.
*****************************************
* FR Encapsulation Configuration *
*****************************************
Current Encapsulation : None
1. RAW (No Encapsulation)
2. Proprietary Voice DLCI
3. RFC 1490
4. ATM RFC 1483 (Tunneling) 
						

							Avaya, Inc. - 119 - PARTNER ACS 1600 DSL module User Guide
6. Select the encapsulation method to use.
The FR DLCI Options submenu displays.
*****************************************
* FR DLCI Options *
*****************************************
1. Configure Transmit CIR
2. Configure Receive CIR
3. Configure FRF.12 Fragmentation
7. Do one of the following:
Select Configure Transmit CIR or Configure
Receive CIR, and then follow the on-screen
messages to set:
Committed burst size (Bc)
Circuit throughput
Excess burst size (Be)
Select Configure FRF .12 Fragmentation, and
then follow the on-screen messages to:
Enable/Disable End-to-End FRF .12
Set Fragment Size
You must restart the PARTNER ACS 1600 DSL module
for any changes to take effect.  For more information on
restarting the PARTNER ACS 1600 DSL module, see the
“Getting started” chapter.
Deleting a DLCI
To delete a DLCI:
1. On the Main Menu, select Configure WAN, and then type
the slot number of the WAN interface that you want to
configure.
The WAN Configuration Menu displays.
2. Select Configure DLCIs.
The FR DLCI Config Menu displays.
*****************************************
* FR DLCI Config Menu *
*****************************************
1. Add New DLCI
2. Modify Existing DLCI
3. Delete DLCI