ATT DEFINITY Communications System Generic 3 Planning And Configuration Instructions Manual

							HARDWARE AND SOFTWARE DETERMINATIONaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa
DISK DRIVE (TN1657) (G3r Only)
Enter the number of:
(A) Center Stage Switches (CSSs)
One disk drive only is needed for a simplex G3r system with a CSS. Two are required for dupli-
cated systems.  Optionally, the disk drive may also be added to increase booting speed.
PEC
____ 63324
PACKET DATA LINE (TN553) (G3r Only)
Every time you have a TN553, youll need at least 1 TN726 port.
Enter the number of:
(A) CDR Ports
(B) Serial printer
(C) Manager 1 switch connected (instead of EIA-232 connected)
(D) Property Management System
(E) TN750 Announcement circuit pack
(F) BCMS Terminal
(G) G3r-MA Terminal
PEC
TOTAL PORTS  ____ ¸12 = ____ 63318
76 
						

							aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaHARDWARE AND SOFTWARE DETERMINATION
ISDN-BRI LINE (TN556)
Enter the number of:
(A) 7505 ISDN-BRI voice terminals
(B) 7506 ISDN-BRI voice terminals
(C) 7507 ISDN-BRI voice terminals
(D) 8503T ISDN-BRI voice terminals
(E) CallVisor ASAI adjuncts
PEC
TOTAL PORTS  ____ ¸12 = ____ 65512
Note:Using a passive bus arrangement, you can have up to 24 voice terminals per circuit
pack.  However, the terminals would have to be voice only.
77 
						

							HARDWARE AND SOFTWARE DETERMINATIONaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa
PACKET GATEWAY (TN577) (G3r Only)
Enter the number of:
(A) AUDIX Data Links
(B) 3B Applications (CMS, MSA, CallVisor ISDN Gateway)
(C) DCSs Between Switches
PEC
TOTAL PORTS  ____ ¸4 = ____ 63317
78 
						

							aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaHARDWARE AND SOFTWARE DETERMINATION
ANALOG LINE (TN742)
If you are reusing a TN742 from an earlier system, enter the number of:
(A) 7100 Series Sets ......................................................................................................  ____
(B) 2500/2554-Type Sets (On Premises) ........................................................................  ____
(C) 2500/2554-Type Off-Premises Extensions................................................................  ____
(D) 2500-Type Sets with Message Waiting
Indicator/Recall capability.........................................................................................  ____
(E) Rotary Dial Telephones (500-Type) ..........................................................................  ____
(F) 510As.......................................................................................................................  ____
(G) Recorded Announcement Lines ...............................................................................  ____
(H) Teleconferencing Lines
(QUORUMÒteleconferencing equipment or CPE) ...................................................  ____
(I) Lines Equipped With Modems Only ...........................................................................  ____
(J) External Pooled Modems ..........................................................................................  ____
(K) Queue Warning Lamps (for UCD/DDC) ....................................................................  ____
(L) Loudspeaker Paging Access Lines ...........................................................................  ____
(M) Code Calling Access Lines ......................................................................................  ____
(N) Radio Paging Access Lines (Requiring Tip and Ring only)........................................  ____
(O) Recorded Telephone Dictation Lines
(Requiring Tip and Ring only) ...................................................................................  ____
(P) Analog Lines for other CPE ......................................................................................  ____
(Q) Line for TAAS External Alert ....................................................................................  ____
(R) Future Growth ..........................................................................................................  ____
PEC
TOTAL PORTS  ____ ¸8 = ____ 63111
Additional information on analog line characteristics is in the following table.
79 
						

							HARDWARE AND SOFTWARE DETERMINATIONaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa
bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
Analog Line Circuit Packs
bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
Feature TN742 TN769 TN746 TN746B TN479
bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb
Number of Ports 8 8 16 16 16bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbNeon Message Waiting Indicators No Yes Yes Yes YesbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbLED Terminals Yes Yes Yes Yes YesbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbFeed Voltage -48 V -48 V -24 V -48 V -24VbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbHard Bridging Yes Yes No Yes NobbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbStation Adjunct Yes Yes No Yes NobbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbSecondary Lightning Protection Yes Yes No Yes NobbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbSame PremisesÐOut-of-Building Yes Yes No Yes NobbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbTerminals 500-Type 500-Type 500-Type 500-Type 500-Type
2500-Type 2500-Type 2500-Type 2500-Type 2500-Type
7100 Series 7100 Series 7102A*  7100 Series 7100 Series
bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbRange With 500-Type/ 20,000 20,000 3,100 20,000 3,000
2500-Type/7102A Terminals²Feet Feet Feet Feet Feet
(24-Gauge Wire)
bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbRange With 7101A/7103A 15,200 15,200 Not 15,200 Not
Terminals Feet Feet Supported Feet Supported
(24-Gauge Wire)
bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbRinger Loads 3 3 3 3 3bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbSimultaneous Ports Ringing 4 4 4 8 ² 4
Ringing
bbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbbb c c c c
c
c
c c c
c
c
c c c
c
c
c c c
c
c
c c c
c
c
c
c c c c
c
c
c c c
c
c
c c c
c
c
c c c
c
c
c c c
c
c
c
c c c c
c
c
c c c
c
c
c c c
c
c
c c c
c
c
c c c
c
c c c c
c
c
c c c
c
c
c c c
c
c
c c c
c
c
c c c
c
c c c c
c
c
c c c
c
c
c c c
c
c
c c c
c
c
c c c
c
c c c c
c
c
c c c
c
c
c c c
c
c
c c c
c
c
c c c
c
c c c c
c
c
c c c
c
c
c c c
c
c
c c c
c
c
c c c
c
c
c
aaaaaaaaaaaaaaaaaaa
*  The TN746 circuit pack supports the 7102A terminal, but does not support the 7101A or 7103A terminals.
² The TN746B circuit pack allows ringing on four ports of each half of the circuit pack (for a maximum of  eight
simultaneous ports ringing). A user attempting to ring one half of the circuit pack when all four ports are busy receives
the busy tone.
80 
						

							aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaHARDWARE AND SOFTWARE DETERMINATION
CALL CLASSIFIER (TN744)
Eight touch-tone receiver ports are provided on each TN744 Call Classifier circuit pack.  The
TN744 circuit pack is used exclusively for receiving touch-tone input for the Call Prompting
feature, classifying outgoing calls for the Answer Detection feature, and classifying outgoing calls
for an outgoing call management system.  Each of these are optional features that must be prop-
erly engineered.  A maximum of 10 TN744 may be used in a G3i or G3r system (TN744 is not
supported in G1).
Enter the number of:
(A) Touch-tone receivers for Call Prompting  ..................................................................  ____
(B) Touch-tone receivers for Answer Detection ..............................................................  ____
(C) Touch-tone receivers for outbound call management ...............................................  ____
PEC
TOTAL PORTS  ____ ¸8 = ____ 63532
81 
						

							HARDWARE AND SOFTWARE DETERMINATIONaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa
ANALOG LINE (TN746)
Enter the number of:
(A) 7100 Series Sets ......................................................................................................  ____
(B) 2500/2554-Type Sets (On Premises) ........................................................................  ____
(C) 2500/2554-Type Off-Premises Extensions................................................................  ____
(D) 2500-Type Sets with Message Waiting
Indicator/Recall capability.........................................................................................  ____
(E) Rotary Dial Telephones (500-Type) ..........................................................................  ____
(F) 510As.......................................................................................................................  ____
(G) Recorded Announcement Lines ...............................................................................  ____
(H) Teleconferencing Lines
(QUORUMÒteleconferencing equipment or CPE) ...................................................  ____
(I) Lines Equipped With Modems Only ...........................................................................  ____
(J) External Pooled Modems ..........................................................................................  ____
(K) Queue Warning Lamps (for UCD/DDC) ....................................................................  ____
(L) Loudspeaker Paging Access Lines ...........................................................................  ____
(M) Code Calling Access Lines ......................................................................................  ____
(N) Radio Paging Access Lines (Requiring Tip and Ring only)........................................  ____
(O) Recorded Telephone Dictation Lines
(Requiring Tip and Ring only) ...................................................................................  ____
(P) Analog Lines for other CPE ......................................................................................  ____
(Q) Line for TAAS External Alert ....................................................................................  ____
(R) Future Growth ..........................................................................................................  ____
PEC
TOTAL PORTS  ____ ¸16 = ____ 63136
For additional information on analog line circuit pack characteristics, see ``Analog Line (TN742).
82 
						

							aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaHARDWARE AND SOFTWARE DETERMINATION
ANALOG LINE (TN479 - For International DEFINITY G1 Only)
Enter the number of:
(A) 7100 Series Sets ......................................................................................................  ____
(B) 2500/2554-Type Sets (On Premises) ........................................................................  ____
(C) 2500/2554-Type Off-Premises Extensions................................................................  ____
(D) 2500-Type Sets with Message Waiting
Indicator/Recall capability.........................................................................................  ____
(E) Rotary Dial Telephones (500-Type) ..........................................................................  ____
(F) 510As.......................................................................................................................  ____
(G) Recorded Announcement Lines ...............................................................................  ____
(H) Teleconferencing Lines
(QUORUMÒteleconferencing equipment or CPE) ...................................................  ____
(I) Lines Equipped With Modems Only ...........................................................................  ____
(J) External Pooled Modems ..........................................................................................  ____
(K) Queue Warning Lamps (for UCD/DDC) ....................................................................  ____
(L) Loudspeaker Paging Access Lines ...........................................................................  ____
(M) Code Calling Access Lines ......................................................................................  ____
(N) Radio Paging Access Lines (Requiring Tip and Ring only)........................................  ____
(O) Recorded Telephone Dictation Lines
(Requiring Tip and Ring only) ...................................................................................  ____
(P) Analog Lines for other CPE ......................................................................................  ____
(Q) Line for TAAS External Alert ....................................................................................  ____
(R) Future Growth ..........................................................................................................  ____
PEC
TOTAL PORTS  ____ ¸16 = ____ 63803I
For additional information on analog line circuit pack characteristics, see ``Analog Line (TN742).
83 
						

							HARDWARE AND SOFTWARE DETERMINATIONaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa
ANALOG LINE (TN769)
This circuit pack is used for voice terminals with neon message waiting lamps.
If you are reusing a TN769 from an earlier system, enter the number of:
(A) 7100 Series Sets ......................................................................................................  ____
(B) 2500/2554-Type Sets (On Premises) ........................................................................  ____
(C) 2500-Type Sets with Message Waiting
Indicator/Recall capability.........................................................................................  ____
(D) Rotary Dial Telephones (500-Type) ..........................................................................  ____
(E) 510As ......................................................................................................................  ____
(F) Recorded Announcement Lines (Max 10) .................................................................  ____
(G) Teleconferencing Lines (Max 28)
(QUORUMÒteleconferencing equipment or CPE) ...................................................  ____
(H) Lines Equipped With Modems Only ..........................................................................  ____
(I) External Pooled Modems ...........................................................................................  ____
(J) Queue Warning Lamps (for UCD/DDC) .....................................................................  ____
(K) Loudspeaker Paging Access Lines ...........................................................................  ____
(L) Code Calling Access Lines .......................................................................................  ____
(M) Radio Paging Access Lines (Requiring Tip and Ring only) .......................................  ____
(N) Recorded Telephone Dictation Lines
(Requiring Tip and Ring only) ...................................................................................  ____
(O) Analog Lines for other CPE ......................................................................................  ____
(P) Line for TAAS External Alert .....................................................................................  ____
(Q) Future Growth..........................................................................................................  ____
PEC
TOTAL PORTS  ____ ¸8  = ____ 63142
For additional information on analog line circuit pack characteristics, see ``Analog Line (TN742).
84 
						

							aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaHARDWARE AND SOFTWARE DETERMINATION
AUXILIARY TRUNK (TN763)
Enter the number of:
(A) Trunks for Code Calling (Max 10) .............................................................................  ____
(B) Trunks for Loudspeaker Paging Access (Max 10) (See Note) ...................................  ____
(C) Trunks for Recorded Telephone Dictation.................................................................  ____
(D) Music-on-Hold (Max 1) .............................................................................................  ____
(E) Trunks for other CPE (Audichron).............................................................................  ____
(F) Future Growth ..........................................................................................................  ____
(G) (G3r Only) Malicious Call Trace................................................................................  ____
(H) (G3r Only) Recorded Announcements ......................................................................  ____
PEC
TOTAL PORTS  ____ ¸4 = ____ 63118
Note:A 278A adapter and power supply is required for each paging zone, unless PagePac
paging system equipment is used.
CENTRAL OFFICE TRUNK (TN747)
Enter the number of lines that will terminate as either trunk lines or as personal lines:
(A) CO Lines ..................................................................................................................  ____
(B) WATS Lines .............................................................................................................  ____
(C) 800 Service Lines ....................................................................................................  ____
(D) FX Lines ..................................................................................................................  ____
(E) Future Growth ..........................................................................................................  ____
PEC
TOTAL PORTS  ____ ¸8 = ____ 63115
85