ATT Definity Addendum 1 For Ds1, Dmi, Isdn Pri Instructions Manual

ADMINISTRATION OPTIONS AND REQUIREMENTS — SYSTEM 857-13
Field 14V3-V4
Field encodes and their descriptions are:
0
Selects the DS1/DMI-BOS channels used for both trunks and lines; the latter is
frequently called OPS. Each DS1/MFAT carrier will support a maximum of two
DS1s (slots 5 and 18).½
The ACCUNET switched digital service can be provided by setting up a trunk
group with encode 109. However, a DS1 must be optioned for RBS (procedure
260, field 8). The only other administration requirement is that the...

7-14ADMINISTRATION OPTIONS AND REQUIREMENTS — SYSTEM 85½
DS1/OPS Related Translations
When a DS1 facility is used exclusively for lines, it must be administered for RBS.
Also, the facility cannot be used as a synchronization reference.
When a DS1 is administered for lines (OPS), it provides 24 channels that terminate in
a remote D4-channel bank, CDM, or their equivalent.
Each analog line circuit pack provides eight circuits. Therefore, one DS1/OPS replaces
three analog circuit packs. Each DS1 or...

ADMINISTRATION OPTIONS AND REQUIREMENTS — SYSTEM 857-15
Field 15V4 Only
ZCS facilities require that the contents of the D-channel be inverted to guarantee that
the minimum ones-density be maintained. This field shows whether the signaling
channel is inverted. Field encodes and their descriptions are:½
–
(Dash) means ZCS chosen in procedure 260. This is the default when ZCS is
chosen (this automatically inverts the D-channel).
The dash is appropriate for all applications of the ANN11 circuit pack. RBS...

7-16ADMINISTRATION OPTIONS AND REQUIREMENTS — SYSTEM 85
Procedure 262 Word 1: ISDN Board Parameters
Procedure 262 is used in System 85 R2V4 and Generic 2 to administer DMI-MOS (ANN35) for other
service/facility options (DMI-MOS/ISDN-PRI only). Figure 7-5, Procedure 262 Word 1: ISDN Board
Parameters, depicts procedure 262, word 1.½
ENHANCED MODE – PROCEDURE:  262, WORD:  1
ISDN BOARD PARAMETERS
EQUIPMENT LOCATION
1.
2.3.
4.Module:
Cabinet:
Carrier:
Slot:
PRI PARAMETERS
5.
6.
7.Interface Type:
Facility...

ADMINISTRATION OPTIONS AND REQUIREMENTS — SYSTEM 857-17
Field 5V4 Only
Assigns the interface type or side. The default option is (0) for user side. Alternately,
a (1) should be administered for network side. The configuration of the network
should be analyzed to determine if the (0) option is appropriate.½
For MOS-type facilities (such as DMI-MOS and ISDN-PRI), each link must be
segmented into user and network sides. Each System 85 R2V4 MOS-based
transmission facility connecting to the public network...

7-18ADMINISTRATION OPTIONS AND REQUIREMENTS — SYSTEM 85
Field 7V4 Only
This field will accept encodes within the range of 0 through 126. However, all point-
to-point (nonswitched) links, such as an System 85 R2V4 DMI-MOS link to a host
computer, must be administered with encode 0. Encodes 1 through 126 are not used at
this time.½
Field 8 V4 Only
The field will accept encodes ranging from 0 through 255, corresponding to 1-second
intervals for an elapsed time of up to 4 minutes and 15 seconds. The default...

ADMINISTRATION OPTIONS AND REQUIREMENTS — SYSTEM 857-19
ENHANCED MODE - PROCEDURE: 354, WORD: 3
NPA-NXX ASSIGNMENT
1.
2.
3.
4.NPA-NXX Designator:
NPA:
NXX:
Thousands Digit:
Connected to CC0 ON-LINE 
enter command:
Figure 7-6. Procedure 354 Word 3: NPA-NXX Assignment (System 85 R2V4)½
Field 1
Field 2
Field 3
Field 4This field should be translated for both private- and public-network connections. The
NPA-NXX designator is a 2-digit field and must be within the range of 1 through 99.
This 3-digit field...

7-20ADMINISTRATION OPTIONS AND REQUIREMENTS — SYSTEM 85
If the switch contains more than one office code, multiple NPA/NNX designators may be needed.
Figure 7-7, Procedure 000 Word 4: NPA-NXX Partition Assignment (System 85 R2V4), depicts
procedure 000, word 4.½
ENHANCED MODE -PROCEDURE: 000, WORD: 4
EXTENSION NPA-NXX/PARTITION ASSIGNMENT
1.
2.
3.
4.First Extension:
Last Extension:
Extension Partition:
NPA-NXX Designator:
DISPLAY ONLY
5.
Invalid Extension:
Connected to CCO ON-LINE
enter command:
Figure...

ADMINISTRATION OPTIONS AND REQUIREMENTS — SYSTEM 857-21
1.
2.
3.
4.5.
Console Number:
Attendant Partition:
Control:
LDN:
NPA-NXX Designator:
Connected to CC0 ON-LINE
enter command:ENHANCED MODE - PROCEDURE: 210, WORD: 2
CONSOLE ASSIGNMENTS - ATTENDANT PARTITIONS
Figure 7-8. Procedure 210 Word 2: Attendant Partition Assignments (System 85 R2V4)½
Field 1
Field 2
Field 3
Field 4
Field 5Translates a console number. Permitted encodes are any 2-digit number within the
range of 1 through 40.
NOTE: The console...

7-22ADMINISTRATION OPTIONS AND REQUIREMENTS — SYSTEM 85
Procedure 010 Word 4: Line Side (B-Channel) BC and ISDN Routing Options
Figure 7-9, Procedure 010 Word 4: Terminal COS Restrictions (System 85 R2V4), depicts proceure½
010, word 4.
ENHANCED MODE -PROCEDURE : 010, WORD: 4
EXTENSION CLASS OF SERVICE - RESTRICTIONS
1.
2.
3.
4.Class of Service:
Maximum Precedence Level:
Bearer Capability:
ISDN Routing:
Connected to CC0 ON-LINE
enter command:½
Field 1
Field 2Figure 7-9. Procedure 010 Word 4: Terminal COS...