Asus S62f Service Guide

							
                     Assembly procedure  
                                                                                         
                                                  
8.  Install the both hinge Cover. HINGE COVER  ASSEMABLY 
        
 
9.  Install the MIDDLE cover. 
 
 
  
 
 
 
 
 
 
3 - 16   
						

							
                     Assembly procedure  
                                                                                         
                                                  
 
Assembling Keyboard   KEYBOARD 
  
The illustrations below show how to assemble and install the Keyboard of the notebook. 
 
 
KEYBOARD 
ASSEMBLY 
1. Place the Keyboard module on front side of the top case. Then connect Keyboard 
FPC Cable with a pai r of tweezers. 
  
 
  
 
2. Install Keyboard properly and  note the lower side should inset first. Push the 4 
latches to fix the keyboard.  
   
         
 
 
 
 
 
 
 
 
 
 
2 1 4 3 
3 - 17  
						

							
                     Assembly procedure  
                                                                                         
                                                  
ODD Module ODD MODULE 
The illustrations below show how to assemble and install the ODD Module of the 
notebook.  
 
1.  Insert the ODD module. 
 ODD MODULE 
INSTALLATION 
   
 
     
 
2.  Secure 1 screw (M2.5*4L (K)) to secure it. 
 
M2.5*4L 
 
 
 
 
CPU Module Assembly CPU MODULE 
The illustration below shows how  to install CPU and the CPU heat sink of the notebook.   CPU 
INSTALLATION 1. Squeeze the vacuum handling pump  and use it to install the CPU.   
  
  
 
   
 
3 - 18  
						

							
                     Assembly procedure  
                                                                                         
                                                  
2. Turn the non-removable screw here 180 degrees clockwise to lock the CPU. 
 
      
                
3. Install the CPU thernal module gently and connect the  fan cable then secure 2 
screws (M2.5*4L (K)) to secure it. 
 
     
 
4. Secure 4 screws (M2*3L (K)) by order.   
                                  
 
5. Install the CPU door and secure 2  screws (M2.5*4L (K)) to secure it. 
 
Lock 
L 
 
 
O 
M2.5*4L 
 
2 3 
1 4 
M2*3L 
M2.5*4L 
3 - 19   
						

							
                     Assembly procedure  
                                                                                         
                                                  
Assembling Memor y Module 
The illustrations below show how to assemble and install the memory module to the 
notebook . MEMORY 
MODULE   
1.   Insert the Memory modul e into the memory socket by an angle of 30 degree, and 
push down to latch the memory module. 
MEMORY 
INSTALLATION 
 
 
 
 
o30
 
 
2. Install the DIMM door a nd secure 2 screws (M2.5* 4L (K)) to secure it. 
 
M2.5*4L 
 
 
 
Wireless LAN Module WIRELESS 
The illustration below shows how to as semble the Wireless LAN module.   LAN 
 
1.  Install the MINI PCI module into the socket by an angle of 30 degree, and push 
down to latch the MINI PCI module. 
 
 
3 - 20   
						

							
                     Assembly procedure  
                                                                                         
                                                  
2.  Connect the MAIN & AUX antenna and paste 1 piece of tape to secure antennas. 
 
      
 
 
 
 HDD Module  HDD 
MODULE The illustrations below show how to assemb le and install the HDD module of the 
notebook
  
 
1.  Secure 4 screws [M3 * 4(L) ] to fix HDD into HDD housing. HDD 
INSTALLATION  
 
 
M3*4L 
 
 
 
2.  Insert the HDD module to connect  the FPC connector until it’s installed 
properly.  
 
 
 
 
3 - 21   
						

							
                     Assembly procedure  
                                                                                         
                                                  
3.  Install the bottom case and secure 3 screws (M2.5*4L(K)) to fix it.   
 
 
   
M2.5*4L 
     
 
Batter y Module BATTERY 
MODULE The illustrations below show how to install battery module of the notebook. 
 
1.  Install the battery module. Slide the  battery latch to close the battery lock. 
 
 
BATTERY 
INSTALLATION 
 
 
 
 
 
3 - 22  
						

							
                                          Upgrade & Replacement 
 
 
4 – 1 
Chapter 
4 
Upgrade & Replacement 
Follow the individual procedures in this chapter to perform the 
notebook’s upgrade and replacement of  various major components. 
sus S62F Series Notebook is a 2 spindles  product, which means there are less 
options for you to upgrade to.  The key upgradeable and replaceable items include 
the CPU module, memory module , HDD module, and ODD module. 
 
In order to a
void redundancy, please refer to  chapters 2 and 3 of this manual for repeated 
and reused disassembly and assembly procedures , such as keyboard & heat sink replacement, 
which is used by several different procedures in this chapter.  
Be sure to follow the safety 
instructions described in Cha pter 1 to safeguard the notebook against any potential 
damages.  
For any other components which you need to replace not covered in this 
chapter, please refer to Chapters 2 and 3 for  detailed disassembly and assembly and perform 
necessary procedures accordingly. 
A 
 
This chapter includes the following items: 
 
•   CPU Upgrade 
•  Memory Upgrade 
•  HDD Upgrade 
•  ODD Replacement 
  
						

							
                                        Upgrade & Replacement 
 
4 - 2   
CPU Upgrade CPU 
 TheS62F Series Notebook comes standar d with a Intel® Micro-FCPGA Socket 
on the motherboard, which  means it can support all Intel Micro-FCPGA CPUs 
up to 2.13 GHz . 
 
Upgrading CPU 
Remove battery module  
 
1. Unlock and hold the latch No (1). 
 
  
1 
 
2. Slide the battery lock (No. 2) and pull the battery pack out. 
 
   
2 
   
 
 
3. Pull the battery pack out. 
 
  
						

							
                                        Upgrade & Replacement 
 
4 - 3   
Removing CPU Module 
 CPU 
REMOVAL 1.  Remove 2 screws (M2.5*4L (K )), then remove the CPU door. 
 
 
 
2.  Remove 4 screws (M2*3L (K)) by order.  
 
                                                         
 
1 
2 3 
4 
M2.5*4L 
M2*3L 
3.  Disconnect the Fan cable  and remove 2 screws (M2.5*4L (K)) then take 
away the CPU thermal module. 
   
     
M2.5*4L