Apple xserve early 2009 User Manual
Have a look at the manual Apple xserve early 2009 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 195 Apple manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Xserve (Early 2009) Take Apart — Front Panel Board 131 2010-06-28 First Steps Remove: • Top Cover • Locking Mechanism Rod • Front Panel Board Cable • Solid State Drive Tools • ESD wrist strap and mat • Phillips #1 screwdriver Front Panel Board
Xserve (Early 2009) Take Apart — Front Panel Board 132 2010-06-28 Removal 1 Release the two locking levers on the connector and disconnect cable. 2 Remove the two 6-mm screws. 3 Slide the board back slightly and release the two clips on either side. 4 Tilt board up and remove. Replacement 1 Tilt board up slightly and insert board into clips. 2 Slide board forward into front panel assembly. 3 Replace the two 6-mm screws and cable.
Xserve (Early 2009) Take Apart — Drive Interconnect Backplane 133 2010-06-28 First Steps Remove: • Apple Drive Module • Power Supply • Top Cover • Airflow Duct • Fan Array • Power Distribution Cable . Tools • ESD wrist strap and mat • Phillips #2 screwdriver Drive Interconnect Backplane
Xserve (Early 2009) Take Apart — Drive Interconnect Backplane 134 2010-06-28 Removal 1 Loosen the captive thumbscrew. 2 Shift the backplane to the right (towards the enclosure) until it clears the stands. 3 Slightly tilt up the backplane toward the logic board. Removal Note: Do not let the backplane components come into contact with the standoffs or the enclosure as you remove the backplane. Replacement 1 Lower the backplane into the enclosure at a slight angle. Replacement Note: Do not let the backplane components come into contact with the standoffs or the enclosure as you remove the backplane.
Xserve (Early 2009) Take Apart — Drive Interconnect Backplane 135 2010-06-28 2 Rotate the backplane downward and over the four standoffs. 3 Slide the backplane in the direction shown to seat the backplane into enclosure. 4 Tighten the captive thumbscrew. 5 Connect the backplane-to-logic board cable. Verify cable is firmly seated. 6 Connect the front panel board cable to the front panel board.
Xserve (Early 2009) Take Apart — Xserve RAID Card 136 2010-06-28 First Steps Remove: • Apple Drive Module • Power Supply • Top Cover • Airflow Duct • Fan Array • Power Distribution Board Cable • Front Panel Board Cable • Backplane-to-Logic Board Cable Tools • ESD wrist strap and mat • Phillips #2 screwdriver Xserve RAID Card
Xserve (Early 2009) Take Apart — Xserve RAID Card 137 2010-06-28 Removal 1 Remove power distribution cable from Xserve RAID Card. 2 Disconnect the Backplane to Logic Board cable. 3 Disconnect the Xserve RAID Card battery cable from Xserve RAID Card. 4 Loosen the captive thumbscrew. 5 Shift the backplane to the right (towards the enclosure) until it clears the stands. 6 Slightly tilt up the backplane toward the logic board. Removal Note: Do not let the RAID card components come into contact with the standoffs or the enclosure.
Xserve (Early 2009) Take Apart — Xserve RAID Card 138 2010-06-28 Replacement 1 Lower the backplane into the enclosure at a slight angle. Replacement Note: Do not let the RAID card components come into contact with the standoffs or the enclosure. 2 Rotate the backplane downward and over the four standoffs. 3 Slide the backplane to the right in the direction shown to seat the backplane into enclosure. 4 Tighten the captive thumbscrew. 5 Connect the backplane-to-logic board cable. Verify cable is firmly seated. 6 Connect the Xserve RAID card battery cable to the Xserve RAID card. 7 Connect the front panel board cable to the front panel board.
Xserve (Early 2009) Take Apart — Power Distribution Board 139 2010-06-28 First Steps Remove: • Apple Drive Module • Power Supply • Top Cover • Airflow Duct • Fan Array • Drive Interconnect Backplane • Power Distribution Board Cable Tools • ESD wrist strap and mat • Phillips #2 screwdriver Power Distribution Board
Xserve (Early 2009) Take Apart — Power Distribution Board 140 2010-06-28 Removal 1 Release the captive thumbscrew that secures the power distribution board to the enclosure. Removal Note: Captive thumbscrew may be tight, use the Phillips screwdriver to assist in removal. 2 Pull the board toward the left towards the enclosure in the direction shown. 3 Lift up the board and remove it from the enclosure. Replacement 1 Lower the board into the enclosure. 2 Pull the board to the right to lock the board in place. 3 Tighten the captive thumbscrew to secure the board to the enclosure.