Home > Apple > Display > Apple imac 20 inch early 2008 User Manual

Apple imac 20 inch early 2008 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Apple imac 20 inch early 2008 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 195 Apple manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							iMac (20-inch Early 2008)  Take Apart — IR (Infrared) Board 61
    Replacing the IR Board
    1. If removed, connect the IR cable to the IR board.
    Install the two T6 screws from IR board and connect the IR cable to the logic board.
    2.  
     
    Replace the front bezel.3. 
    Clean and r4. eplace the glass panel. Note: This step is very important. Follow the procedures 
    to ensure the glass is clean and free of particles.
    Replace the access door
    5. .
    922-8256 
    						
    							iMac (20-inch Early 2008)  Take Apart — AirPort Extreme Card 62
    AirPort Extreme Card
    Tools
    Torx T6 screwdriver• 
    Preliminary Steps
    Before you begin, remove the following:
    A
    • ccess door
    Glass pane
    • l
    F
    • ront bezel
    Part Location 
    						
    							iMac (20-inch Early 2008)  Take Apart — AirPort Extreme Card 63
    Removing the AirPort Extreme Card
    1. Using a T6 torx screwdriver, remove the 5-mm long screw and disconnect the two antenna 
    cables from the AirPort Extreme card. Note: The antenna cables and connectors are very 
    delicate and should be carefully removed by pulling on the antenna cable connector, not on 
    the cable.
    Holding the card by the edges, pull the AirPort Extreme card out of the slot.2.  
    922-7010 
    						
    							iMac (20-inch Early 2008)  Take Apart — AirPort Extreme Card 64
    Replacing the AirPort Extreme Card
    Align the AirPort Extreme card with the slot on the logic board. Insert the board into the slot.1. 
    2.  Connect the antenna cables to the connectors on the AirPort Extreme card.  
    Note: The antenna cables might include an “L” or “R” tab near the connector end; however, 
    you can disregard that because the cable position can be swapped without any change in 
    performance. 
    Replace the T6 screw.
    3. 
    Replace the front bezel.4.  
    Clean and r5. eplace the glass panel. Note: This step is very important. Follow the procedures 
    to ensure the glass is clean and free of particles.
    Replace the access door
    6.  .
    922-7010 
    						
    							iMac (20-inch Early 2008)  Take Apart — Bluetooth Board 65
    Bluetooth Board
    Tools
    Torx T6 screwdriver• 
    Preliminary Steps
    Before you begin, remove the following:
    A
    • ccess door
    Glass pane
    • l
    F
    • ront bezel
    Part Location 
    						
    							iMac (20-inch Early 2008)  Take Apart — Bluetooth Board 66
    Removing the Bluetooth Board
    Disconnect the blue Bluetooth antenna from the top left corner of the board and the tiny, 1. 
    black cable that connects from the Bluetooth board to the logic board. 
    2.  Using a T6 torx screwdriver, remove the T6 screw from the lower left corner of the Bluetooth 
    board.  Lift the Bluetooth board off the logic board.
    922-7010 
    						
    							iMac (20-inch Early 2008)  Take Apart — Bluetooth Board 67
    Replacing the Bluetooth Board
    Connect the tiny, black Bluetooth cable to the Bluetooth board and to the logic board.1. 
    Press the Bluetooth board onto the logic board connector. 2.  
    Connect the Bluetooth antenna to the Bluetooth board.3. 
    4. Replace the one T6 screw in the lower left corner of the Bluetooth board.
    Replace the front bezel.5. 
    Clean and r6. eplace the glass panel. Note: This step is very important. Follow the procedures 
    to ensure the glass is clean and free of particles.
    Replace the access door
    7.  .
    922-7010 
    						
    							iMac (20-inch Early 2008)  Take Apart — LCD Display Panel 68
    LCD Display Panel
    Tools
    Torx T6 screwdriver• 
    Torx T8 screwdriver• 
    Preliminary Steps
    Before you begin, remove the following:
    A
    • ccess door
    Glass pane
    • l
    F
    • ront bezel
    Important:  To prevent the buildup of static charges which may attract dust particles to the 
    surface of the display, store the LCD display panel in an anti-static bag whenever it has been 
    removed from the system.
    Part Location 
    						
    							iMac (20-inch Early 2008)  Take Apart — LCD Display Panel 69
    Removing the Display Panel
    Place the computer with the display face up.1. 
    2.  Remove the two T6 screws from the LVDS connector. Pull the black tab on the LVDS cable to 
    disconnect it from the logic board.
    3. Remove the eight 8-mm long T8 screws from the sides of the panel frame.
    922-7010
    922-8172 
    						
    							iMac (20-inch Early 2008)  Take Apart — LCD Display Panel 70
    Disconnect the display sensor cable from the connector on the left side of the logic board.
    4.
     
    Grasp the LCD panel at the bottom edge, and tilt up the panel. On the right side, disconnect 5. 
    the four inverter cable connectors. Pull the connectors straight out. DO NOT pull on the 
    wires.
      
    						
    All Apple manuals Comments (0)

    Related Manuals for Apple imac 20 inch early 2008 User Manual