Home > Apple > Display > Apple imac 20 inch early 2008 User Manual

Apple imac 20 inch early 2008 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Apple imac 20 inch early 2008 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 195 Apple manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							iMac (20-inch Early 2008)  Take Apart — Front Bezel 51
    Replace 5. the twelve screws around the bezel. Replacement Note: The four longer screws 
    (25mm) attach to the bezel along the bottom of the panel.
    Clean and r6.  eplace the glass panel.  Note: This step is very important. Follow the procedures to 
    ensure the glass is clean and free of particles.
    Replace the access door
    7.  .
    922-8207, 25 mm
    922-8206, 13 mm 
    						
    							iMac (20-inch Early 2008)  Take Apart — Camera Board 52
    Camera Board
    Tools
    Torx T8 screwdriver • 
    ESD mat, soft , clean towel or cloth• 
    Preliminary Steps
    Before you begin, remove the access door , glass panel,  and front bezel.
    Part Location 
    						
    							iMac (20-inch Early 2008)  Take Apart — Camera Board 53
    Removing the Camera Board
    The camera board bracket and cable are visible after you remove the front bezel off the 1. 
    computer.
    2.  Remove two 9mm T8 screws on the camera bracket.
    Lift the camera bracket out of the rear housing enough to access the kapton tape securing 3. 
    the camera cable.
    922-8171 
    						
    							iMac (20-inch Early 2008)  Take Apart — Camera Board 54
    Unwrap the kapton tape covering the camera cable and connector. Disconnect the camera 
    4.
     
    cable from the camera board. Set the camera board and attached bracket aside.
      
    						
    							iMac (20-inch Early 2008)  Take Apart — Camera Board 55
    Replacing the Camera Board
    Connect the camera cable to the camera board. Make sure the cable is securely inserted into 1. 
    the connector. Reapply the kapton tape over the cable and connector.
    2.  Lower the camera bracket onto the black posts on the rear cover.
    Replace the two T8 screws.
    3. 
    Replace the front bezel.4. 
    Clean and r5. eplace the glass panel. Note: This step is very important. Follow the procedures 
    to ensure the glass is clean and free of particles.
    Replace the access door
    6.  .
    922-8171 
    						
    							iMac (20-inch Early 2008)  Take Apart — Battery 56
    Battery
    Tools
    The only tool required for this procedure is a black stick (or other nonconductive plastic or nylon 
    tool).
    Preliminary Steps
    Before you begin, remove the following:
    A
    • ccess door
    Glass pane
    • l
    F
    • ront bezel
    Part Location 
    						
    							iMac (20-inch Early 2008)  Take Apart — Battery 57
    Removing the Battery
    Use a black stick to pry out the battery from the battery socket on the logic board.1. 
     
    Before installing the battery, make sure the side with the engraved markings (+ side) is up .2.   
    						
    							iMac (20-inch Early 2008)  Take Apart — Battery 58
    Replacing the Battery
    Make sure the battery socket is open and free of dust.1. 
    Press the battery into the socket. Make sure the side with the engraved markings (+ side) is 2.  
    facing up.
    Lower the front bezel, connect the microphone cable, replace the front bezel screws.3. 
    Replace the front bezel.4. 
    Clean and r5. eplace the glass panel. Note: This step is very important. Follow the procedures 
    to ensure the glass is clean and free of particles.
    Replace the access door
    6.  . 
    						
    							iMac (20-inch Early 2008)  Take Apart — IR (Infrared) Board 59
    IR (Infrared) Board
    Tools
    The only tool required for this procedure is a Torx T6 screwdriver.
    Preliminary Steps
    Before you begin, remove the following:
    A
    • ccess door
    Glass pane
    • l
    F
    • ront bezel
    Part Location 
    						
    							iMac (20-inch Early 2008)  Take Apart — IR (Infrared) Board 60
    Removing the IR Board
    1. Remove the two T6 screws from the IR board and disconnect the IR cable from either the IR 
    board or the logic board. Note: It doesn’t matter which board you disconnect the IR cable 
    from when removing the IR board.
     
    Lift the IR board from the heatsink.  2. 
    922-8256 
    						
    All Apple manuals Comments (0)

    Related Manuals for Apple imac 20 inch early 2008 User Manual