Apple imac 20 inch early 2008 User Manual
Have a look at the manual Apple imac 20 inch early 2008 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 195 Apple manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
iMac (20-inch Early 2008) Take Apart — Hard Drive Sensor Cable 131 Removing the Hard Drive Sensor Cable Disconnect the temperature sensor cable from its connector on the top of the logic board.1. Remove the sensor-end of the cable from the sensor clip located under the foam gasket on 2. top of the hard drive
iMac (20-inch Early 2008) Take Apart — Hard Drive Sensor Cable 13 2 Replacing the Hard Drive Sensor Cable Connect the sensor cable to the clip on the hard drive and to the connector on the logic 1. board. Place the foam gasket over the sensor clip. Replace the display panel2. . Replace the front bezel. 3. Clean and replace the glass panel4. . Note: This step is very important. Follow the procedures to ensure the glass is clean and free of particles. Replace the access door 5. .
iMac (20-inch Early 2008) Take Apart — Optical Drive 13 3 Optical Drive Tools Torx T10 screwdriver• Torx T6 screwdriver• Preliminary Steps Before you begin, remove the following: A • ccess door Glass Pane • l F • ront bezel LCD display pane • l Part Location
iMac (20-inch Early 2008) Take Apart — Optical Drive 134 Removing the Optical Drive Warning: When servicing the optical drive, handle it by the edges only. Pressing elsewhere on the drive could damage its internal mechanism. Remove the two T10 screws. 1. 2. Carefully peel back the strip of EMI mesh tape that anchors the bezel end of the drive to the rear cover. 3. Tilt up the optical drive, remove the two T6 screws on the flex cable board. Remove the flex cable board from the end of the optical drive. 922-7018 922-7656
iMac (20-inch Early 2008) Take Apart — Optical Drive 13 5 Disconnect the temperature sensor cable from its connector on the top edge of the logic 4. board. On the bottom of the optical drive, peel back the foam gasket (not shown) and disconnect the sensor from the sensor clip. If you are replacing the optical drive, transfer the EMI mesh tape, the foam gasket, and the 5. temp sensor cable to the replacement drive. The replacement drive includes the plastic mounting brackets, sensor cable clip, slot-load bezel, and the EMI gasket.
iMac (20-inch Early 2008) Take Apart — Optical Drive 13 6 Replacing the Optical Drive Caution: Never press down on or grasp the body of the optical drive when installing it. Pressing or squeezing the body of the optical drive could damage the drive mechanism. 1. Connect the optical sensor cable to the underside of the drive. Place a new foam gasket on top of the sensor clip. Note: Replace the foam gasket when installing a replacement optical drive. A new foam gasket is included with replacement optical and hard drives. 2. Install the flex cable onto the optical drive with two T6 screws. 922-7656
iMac (20-inch Early 2008) Take Apart — Optical Drive 13 7 Insert the optical drive bezel into the rear housing, lining up the bezel with the slot opening.3. 4. Replace the two T10 optical drive screws. Replace the EMI mesh tape on top of the optical drive. 5. Important: Make sure the EMI mesh tape does not cover any of the slot-load opening on the rear cover as you replace the optical drive into the computer assembly. 6. Replace the display panel. Important: Tuck the four inverter cables into the open cavities in the rear housing. If the cables are not tucked into the open areas next to the optical drive, the LCD panel will not lower into place correctly making proper installation of the front bezel difficult. After replacing the optical drive, plug in the computer and test the optical drive by inserting 7. and ejecting DVD-R media. Repeat the insert/eject test three times. Replace the front bezel. 8. Clean and replace the glass panel9. . Note: This step is very important. Follow the procedures to ensure the glass is clean and free of particles. Replace the access door 10. . 922-7018
iMac (20-inch Early 2008) Take Apart — Optical Drive Flex Cable 13 8 Optical Drive Flex Cable Tools A black stick• Preliminary Steps Before you begin, remove the following: A • ccess door Glass Pane • l F • ront bezel LCD display pane • l Optical driv • e Logic boar • d Opti • cal Fan Part Location
iMac (20-inch Early 2008) Take Apart — Optical Drive Flex Cable 13 9 Removing the Optical Flex Cable Release the black tape holding the cable to the chassis. Lift the cable out of the chassis.1.
iMac (20-inch Early 2008) Take Apart — Optical Drive Flex Cable 140 Replacing the Optical Flex Cable Position the cable into the rear housing as shown above.1. Fasten the flexible cable to the chassis with a piece of kapton tape if the black tape doesn’t 2. stick. 3. Replace the optical fan. 4. Replace the logic board . 5. Replace the optical drive. Replace the display panel 6. . Replace the front bezel. 7. Clean and replace the glass panel8. . Note: This step is very important. Follow the procedures to ensure the glass is clean and free of particles. Replace the access door 9. .