Home
>
Anetsberger Brothers
>
Other
>
Anetsberger Brothers GPC14 14 Pasta Pro pasta cooker USER MANUAL
Anetsberger Brothers GPC14 14 Pasta Pro pasta cooker USER MANUAL
Here you can view all the pages of manual Anetsberger Brothers GPC14 14 Pasta Pro pasta cooker USER MANUAL. The Anetsberger Brothers manuals for Other are available online for free. You can easily download all the documents as PDF.
Page 1
GPC-14/18/20 PASTA COOKER GPC PASTA PRO INSTALLATION & USER OPERATION MANUAL GPC-18 shown with optional rinse station. KEEP THIS MANUAL IN A CONVENIENT LOCATION FOR FUTURE REFERENCE. Anets, Inc PO Box 501, Concord, NH 03302-0501 Tel: 603-225-6684 Fax: 603-225-5231 L20-345 Rev 3 NOTICE! After installation of your equipment, immediately contact your local gas supplier to obtain information as to what action to take in...
Page 2
GPC-14/18/20 PASTA COOKER SHIPPING CONTAINER INSPECTION 1. Carefully examine the shipping container for external damage. If damage is noted, notify the delivery carrier immediately. Save all packaging materials for claim examination. 2. If no external damage is noted, remove the unit from the shipping container and carefully examine it for damage. If damage is noted, place the unit in a safe location so that it can be inspected. SPECIFICATIONS * Measured at pressure tap on burner...
Page 3
GPC-14/18/20 PASTA COOKER INSTALLATION INSTRUCTIONS 1. The installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code ANSI Z223.1 latest edition, CAN/CGA -B149.1 & B149.2, Natural Gas Installation Code as applicable including: a. The appliance and its individual shut off valve must be disconnected from the gas supply piping system during any pressure testing of the system at test pressures in excess of ½ psig (3.45 kPa). b. The appliance...
Page 4
GPC-14/18/20 PASTA COOKER OPERATING INSTRUCTIONS LIGHTING PROCEDURE 1. Fill the tank with water to the appropriate level as indicated by the water level marks on the rear of the tank. 2. Turn the gas safety valve knob to the “Pilot” position. 3. Push and hold the knob down & ignite the pilot. 4. Continue to hold the knob for 30 seconds or until the pilot flame does not drop out. 5. Turn the gas safety valve to the “ON” position. 6. Set the thermostat to the desired temperature. 7. If the...
Page 5
GPC-14/18/20 PASTA COOKER CLEANING & MAINTENANCE DAILY CLEANING 1. Follow shutdown procedure and allow hot water to cool. 2. Disconnect the power supply. 3. Open the front door and thread the drain valve extension into the drain valve. 4. Slowly open drain valve and drain water. CAUTION: HOT WATER! 5. Wipe out and rinse tank. 6. Close drain valve and remove extension. 7. Refill tank with clean water. 8. Follow the lighting procedure. NOTE: The cooker automatically shuts off the...
Page 6
GPC-14/18/20 PASTA COOKER TROUBLESHOOTING PROBLEM Water is cold (Burners not firing) Thermostat 25º F or more below the knob set point. Pilot will not remain lit. Burner flames too large. CAUSE No gas supply Inadequate gas supply No Pilot Safety valve knob is in the “Pilot” position Thermostat is set too low. Low supply gas pressure....
Page 7
GPC-14/18/20 PASTA COOKER TROUBLESHOOTING - AUTOMATIC LIFT MECHANISM PROBLEM Basket does not lower when the timer control pushbutton is pressed after the knob is set to a time value. Basket does not raise after the timer reaches a value of zero. Basket lowers and raises repeatedly. Basket raises after the timer has reached a value of zero, but then sinks back into the tank....
Page 10
In the event of problems with or questions In the event of problems with or questions about about your order, please contact the Anets your equipment, please contact the Anets factory at: Authorized Service and Parts representative (603)-225-6684 World Wide (ASAP) covering your area, or contact Anets Website Address: www.anets.com at the number listed to the left. MAILING ADDRESS – P.O. BOX 501,...