Analog Devices ICE1000ICE2000 Emulator Users Guide Rev 12

ICE-1000/ICE-2000 Emulator User’s Guide 1-9 Getting Started
Refer to the online help for information about “target configurator”, 
“JTAG/SWD voltage”, “JTAG/SWD frequency”, and “ICE test”.
JTAG/SWD Frequency
The ICE-1000 emulator supports JTAG/SWD clock operation at 5 MHz. 
The ICE-2000 emulator supports JTAG/SWD clock operation at 1, 5, 9, 
15, 23 and 46 MHz. There is a relationship between the JTAG/SWD fre-
quency and the core clock frequency of the processor. The core clock 
should be at least twice...

Troubleshooting and Warranty
1-10 ICE-1000/ICE-2000 Emulator User’s GuideAlso included in the EE-Note, complete warranty and return material 
authorization (RMA) information for emulators and EZ-KIT Lite prod-
ucts. In general, emulators less than one year old are within warranty, and 
repairs within that period are free of charge, but there are some limitations 
to this warranty coverage. For details, see the note.  

ICE-1000/ICE-2000 Emulator User’s Guide 2-1 
2 HARDWARE DESCRIPTION
This chapter describes the hardware design of the ICE-1000/ICE-2000 
emulator and includes the following sections:
LED
Describes the LED which inform you of the emulator’s status.
Resetting the Target
Describes how to reset the target.
Custom Processor Boards
Describes concerns regarding board lay out.
Mechanical Specifications 
Provides dimensional information.
LED
There is one multicolored LED located on the emulator. It is labeled...

Connectors
2-2 ICE-1000/ICE-2000 Emulator User’s Guide Cyan – Signifies that the ICE is operating in SWD mode. The 
LED will blink during USB activity between the host PC and the 
emulator.
 Yellow – Signifies that there is an issue with the EMU signal on the 
target board and therefore this signal will be ignored by the 
emulator.
Connectors
There are two connectors on the ICE-1000 used for connecting to a tar-
get. 
J1 is a 0.1 14-pin connector used for interfacing with legacy targets. 
This connector...

ICE-1000/ICE-2000 Emulator User’s Guide 2-3 Hardware Description
To reset the target through the software, use the Reset Target command.
 CCES users choose Target > Debug > Reset Target.
 VisualDSP++ users choose Debug > Reset Target.
The Reset Target command sends a reset pulse of the specified duration to 
the target. The reset duration is configured by choosing 
Target > Settings > Reset Target Options. See the online help for more 
information. 
Custom Processor Boards
When designing a custom...

Mechanical Specifications
2-4 ICE-1000/ICE-2000 Emulator User’s GuideCare must be taken when locating a custom target JTAG/SWD interface 
connector, that no components are taller than about 0.135 if located 
under the ICE-1000.     
If there are any concerns that emulator components may short to 
the target board, an insulator should be used to provide protection. Figure 2-1. Emulator Dimensions (in inches) 

ICE-1000/ICE-2000 Emulator User’s Guide 3-1 
3 SUPPORT
Analog Devices provides free technical support.      
Technical Support
For technical support, visit the Embedded Processing and DSP Technical 
Support page at: 
http://www.analog.com/support.
From there you can:
 Access the EngineerZone DSP Support Forum where Analog 
Devices support team members and other designers exchange ideas 
and answer questions 
 Search our vast Knowledge Base containing application notes, data 
sheets, code examples,...

Quality Assurance
3-2 ICE-1000/ICE-2000 Emulator User’s Guide
Quality Assurance
Analog Devices is committed to providing quality products and services. 
To continually provide this quality, please contact our Quality Assurance 
Department directly if you have any concerns at (603) 883-2430, Monday 
through Friday during normal business hours, or through e-mail at:
[email protected].
Our Quality Assurance manager will listen to your concerns and provide a 
timely and effective solution. 

ICE-1000/ICE-2000 Emulator User’s Guide 4-1 
4 REFERENCES
This section describes documentation resources helpful in your 
application development.
 For information on designing the interface between an Analog 
Devices processor and the emulation header on your custom 
processor target board, refer to Engineer-to-Engineer Note, Analog 
Devices JTAG/SWD Emulation Technical Reference (EE-68), 
available from the Analog Devices Web site. 
 For information on the architecture and system interface of the...

4-2 ICE-1000/ICE-2000 Emulator User’s Guide