Alpha Tool.Com.HK Limited Stone Cutter ECCKIT User Manual

							31
5.  Loosen carriage lock 
wing screw which is 
located at the front 
right of the carriage 
assembly.  (See 
Figure  51)
6.  Slide carriage assembly 
in a back and forth 
motion to assure smooth 
operation as shown in 
Figure 52.
Figure-52
Figure-51Wing Screw   
						

							32
TABLE SIDE EXTENSION SUPPORT
This extension support is used for stabilization of large pieces of material.
1. Locate the two lock knobs located on the underside of the table. (See Figure 54)
3.  Loosen these knobs and pull the side extension support outward towards desired 
location as shown.  (See Figure 53)
4.  Re-tighten the lock knobs to a hand tight condition.  
Side Extension Support
Lock Knob
Figure-53
Figure-54   
						

							33
ECOCUTTER DUST HOSE AND BAG INSTALLATION
1.  Install back flow preventer assembly 
to the Ecocutter exhaust port with the 
dust gate in the upright position as 
shown in Figure 55.
2.  Slide the dust hose onto the assembly as 
shown in Figure 56.
3.  Check for a tight connection as shown 
in Figure 57.
4.  Route the dust hose and power cord through 
the hose holder as shown in Figure 58.
Dust Hose
Dust Gate
Figure-55
Figure-56
Figure-57
Figure-58   
						

							34
5. Slip the dust bag over hose end as 
 shown in Figure 59.
6. Secure with hook and loop strap as 
 shown as in Figure 60.
7. See Figure 61 for completed 
 Dust Bag installation.
Dust bagFigure-59
Figure-60
Figure-61   
						

							35
8.  Use supplied hook and loop straps (Part No. 133551) to secure power cord to dust 
hose, and dust hose to hoseholder.  (See Figure 62)
Figure-62
Power Cord
Hook and Loop Strap
Hook and Loop Strap
Dust Hose   
						

							36
ALPHA® ECOCUTTER SCHEMATIC (ECC-125)
29
ALPHA® ECOCUTTER SCHEMATIC (ECC-125)
Accessories
1
2
3
4
5
6
7 8
9
10
11
12
13
14
15
16
17
18
19
20
21 22
23
24
25
26
27
28
29 30
31 33
3837
36
35
34
32 39
40
42
43
44
45
46
47
48
45
50
51
52
44
63
45
44
60
59
58 57
31
56 55
45
66
64 80
79
67
68
6970
78 77
7675
74
87
88 89
90
90 9386 87
92
91
82
838485 97
3 96
65
95
98
73
71 72 2
98
81 99
100   
						

							37
    
 ALPHA® ECOCUTTER PARTS LIST
DRAWING NO.PART  NO.DESCRIPTIONQUANTITY
1133080Screw M5×403
2130031Self-tapping Screw 3.9 X192
3133033Carbon Brush (2 pc set)2
4133032Brush Cap2
5130618Block Terminal2
6133040Wire Terminal2
7133086Cable Clamp1
8133042Insulation Pipe2
9133034Brush Terminal Assembly2
10133436/133004Field Coil 110V/220V1
11133551Hook & Loop Straps2
12133003Rear Motor Housing (Blue)1
13133041Cable Clip2
14133044Rubber Switch Cover1
15133043Switch (With Screw)1
16133392Condenser Assembly1
17133029Self-tapping Screw 4.8×652
18133028Bearing Sleeve1
19133078Handle (for ECC-125)1
20133050Woodruff Key1
21133051Snap Ring M81
22133030Air Bridge1
23133025Bearing 608-2RZ1
24133024Insulation Disc1
25133439/133012Armature 110V/220V1
26133026Bearing Cover1
27133027Bearing 629-2RZ1
28133048Gear (Small)1
29133460Self-tapping Screw 3.9X166
30133493Fan Case L1
31133505Cap Screws M5x103
32133497Fan Case R1 
						

							38
 ALPHA® ECOCUTTER PARTS LIST
DRAWING NO.PART  NO.DESCRIPTIONQUANTITY
33133531Dust Gate1
34133530Anti-Back-Flow Flap1
35133047Cable Sleeve1
36133452/133547Rated Plate 110V/220V1
37133475/133546Breaker Assembly (w/cord)110V/220V1
38133474Cord (w/o breaker)110V1
39133533Dust Hose1
40133532Dust Bag Holder1
42133544Dust Bag w/Strap 17”x13 1-/2” x12”1
43133503Pulley (Outside) 21mm OD LHT Fan1
44133502Felt Rings D19xD12xT23
45133492Bearing 698 2RS4
46133498Spacer D12xd8.5x4T1
47133511Knob Bolt1
48133500Bearing Housing1
50133508Outer Belt1
51133488Pulley (Outside) 24mm OD RHT1
52133495Fan1
55133496Fan Shaft1
56133486Housing Adapter1
57133483Main Housing1
58801086Side Handle (for AWS-125/ECC-125)1
59133522Screws M4x155
60133490Pulley (Inside) 18mm OD RHT1
63133487Pulley Shaft1
64133513Screw M4x254
65133545Screw M5x401
66133386Gear Housing1
67133058Gear (Big)1
68133066Needle Bearing Bk 08101
69133368Gear Housing1
70133067O Ring 25.5×21  
						

							39
 ALPHA® ECOCUTTER PARTS LIST
DRAWING NO.PART  NO.DESCRIPTIONQUANTITY
71133512Screw M5x153
72133529Sleeve1
73133510Outer Cover1
74133053Bearing 6201-2RS1
75133060Screw Cap1
76133062O Ring 18×2.51
77133481Spindle (for ECC-125)1
78133506Pulley (Inside) 36mm OD Spindle1
79133509Inner Belt1
80133514Inner Cover1
81133515Screw M5x30 (use part #133513)1
82133521Side Cover1
83133519Flange Bolt1
84133518Flange Outer (for ECC-125)1
85133516Flange Inner (for ECC-125)1
86133071Flat Washer M61
87133084Wing Screw3
88133269Washer For Ruler2
89133528Guide Pin1
90130798Retaining Rings -E1
91133527TT Ruler Guide (for ECC-125)1
92133523Base Plate Assembly1
93133072Spring Washer M6 1
95133535Wrench (for ECC-125)1
96133534Hexagon Ring Spanner1
97133369Felt Strip Set2
98133615Felt Rings D26.6xD12.5xT21
99133616Dust Shield D43xD23xT0.351
100133696Inner Cover Gasket (for ECC-125)1
(not shown)133536BMC (Blow Mold Case) for ECC-1251
(not shown)801392Dust Bag for Carriage 16x13-1/2x81  
						

							Copyright © 2013 Alpha Professional Tools. All rights reserved. 
103 Bauer Drive, Oakland, NJ 07436 • 800-648-7229 • Fax: 800-286-0114www.alpha-tools.com
02/28/2013