Alpha Tool.Com.HK Limited Stone Cutter ECCKIT User Manual

Part No:  ECC-125 
  ECC-STAND
   ECC-TABLE
103 Bauer Drive, Oakland, NJ 07436 • 800-648-7229 • Fax: 800-286-01 14
www.alpha-tools.com
Alpha® Ecocutter
Dr y Tile Cutting System
Instruction Manual
MANUAL
Version 5 

2
TABLE OF CONTENTS
Introduction ........................................................................\
........................................3
About the Symbols ........................................................................\
.......................3
 Safety Instructions ........................................................................\
.......................3
Ecocutter Stand ........................................................................\...

3
INTRODUCTION
Thank you for purchasing the Alpha® Ecocutter Dry Tile Cutting System.  Please read this 
instruction manual thoroughly to ensure safe and correct use of the Ecocutter Dry Tile Cut-
ting System.   Keep this manual in a place where operators can access it easily whenever 
necessary.
 ABOUT THE SYMBOLS
According to the hazard level, all safety notes in this manual are classified into “DANGER”,  
“WARNING”, and “CAUTION”.
    DANGER! Death or serious personal injury is imminent when handling...

4
For Safe Operation
1. Keep work area clean
 Cluttered areas and benches invite injuries.
2. Consider work area environment
 Do not expose power tools to rain. Do not use power tools in damp or wet locations 
without GFCI protection.  Keep work areas well lit. Do not use the tool in presence of 
flammable liquids or gases.
3. Guard against electric shock
 Prevent body contact with grounded surfaces. For example: pipes, radiators, ranges, 
and refrigerator enclosures; use grounded outlets. 
4. Keep...

5
14. Disconnect tools
 Disconnect the tool from the power supply when not in use, before servicing, and when 
changing accessories, such as blades, bits, cutters.
15. Remove adjusting keys and wrenches
 Check to see that keys and adjusting wrenches are removed from the tool \
before 
turning it on.
16. Avoid unintentional starting
 Do not carry a plugged-in tool with finger on switch. Be sure the switch is off when 
plugging in.
17. Outdoor use extension cords
 When tool is used outdoors, use only...

6
ALPHA®  ECOCUTTER STAND (ECC-STAND)
 COMPONENTS: 
1. 2 Bolts and Hardware (for folding leg assembly) (Part No. 200026)
2. 8 Bolts and Hardware (for casters) 
3.  2 Locking Casters  
4.  2 Legs  (Front Saw Stand, Part No. 200020 — Rear Saw Stand, Part No. 200021)
5. 2 Wing Screws (Part No. 200024)
After removal of all cutting table base components from packing, check f\
or each item listed 
below:





Figure-1
(Part No. 200022)   

7
 ASSEMBLY OF ECOCUTTER STAND 
The following tools will be needed to assemble this base section of the \
cutting table for 
the Ecocutter.
 2 - 14mm wrenches
 1 - 11mm wrench
 1 - 10mm wrench
1.  Position the two legs to create a scissor 
configuration as shown in Figure 2.
Figure-2
2.  Turn assembly on its side and align the 
holes located at the center of each leg. 
Insert one of the two large bolts (Part No. 
200026) using a flat washer on each side 
followed by the nylon insert lock nut as 
shown in...

8
3. Tighten bolts until a slight gap remains 
between the two legs.  See Figure 5 and 
Figure 6.
4.  Legs must move freely in a scissor motion  
(See Figure 6).  Note: an over tightened 
condition will cause binding of the legs.
Figure-5
Figure-6
Air Gap   

9
 CASTER INSTALLATION
1.  Place and align caster mounting plate with mounting holes on base 
of stand leg as shown in Figure 7 and Figure 8.
2.  Insert the four bolts for the 
casters with washers on each 
side and lock nut as shown in 
Figure 9.
3.   Tighten until snug.
Figure-7
Figure-8
Figure-9   

10
5. See Figure 11 for complete assembled 
base stand in the opened position.
6.  See Figure 12 for complete assembled 
base stand in the folded position used 
for transport.
4.  Repeat process for second caster as 
     shown in Figure 10.
Figure-10
Figure-11
Figure-12