Alpha Tool.Com.HK Limited Stone Cutter ECCKIT User Manual

21
3.  Install supplied screw from the underside 
of the saw base as shown in Figure 32.
4.  Install supplied washer, lock washer and   
wing nut as shown in Figure 33.
5. Position hose holder at 90 degrees to the 
saw base and hand tighten wing nut to lock 
in position.
Figure-32
Figure-33
Figure-34  

22
 INSTALLATION OF THE ANGLE AND RIP GUIDES
Angle Guide
Rip Guide
Ruler Stopper
Figure-36
1. Angle and Rip Guides will mount to Ruler Stopper.
Figure-35   

23
2.  Place channel of angle and rip guide over edge of ruler stopper and then tighten thumb 
nail screws to secure, when in the correct position.
Figure-38
Figure-39
Figure-37
Figure-40
Example of mounted Angle and Rip Guides for cutting diagonally across a tile.
Rip GuideAngle Guide
Ruler Stopper
Figure-41   

24
ALPHA® ECOCUTTER TABLE SCHEMATIC (ECC-TABLE)    

25
ALPHA® ECOCUTTER TABLE PARTS LIST
DRAWING NO.PART NO.DESCRIPTIONQUANTITY
1200001Hose Holder Assembly1
2200002Stabilizer Assembly1
3200003Saw Base Assembly1
4200004Tube Slider Assembly1
5200005Base Stopper Assembly1
6200006Hollow Rail Tube Assembly1
7200007Solid Rail Tube Assembly1
8200008Rail Holder Assembly1
9200009Carry Handle Assembly1
10200010End Seal Plate Assembly1
11200011Removable Ruler Stopper Assembly1
12200012Removable Filler Assembly1
13200013Assembled Table1
14200014Rubber Mat Set1...

26
1.  Locate and remove clamp assembly from 
saw base.
2.  Loosen wing screw on 
the depth indicator of 
the Ecocutter and raise 
to the highest level as 
shown in Figure 43.
3.  Hand tighten wing 
screw at this position.
INSTALLATION OF ECOCUTTER TO SAW BASE
CLAMPS
Saw Base
Blade clearance slot
Wing Screw
Clamp Assembly
Figure-42
Figure-43   

27
4. Place and position the Ecocutter within the clamp bases as shown in Figure 44.
Figure-44
Figure-45
5.  Place each of the four clamp assemblies over the Ecocutter base and tighten as shown 
in Figure 45.   

28
COMPONENTS:
1. Stabilizer Bracket Bolt 
2. Wing Nut
3. Base hardware
4. Stabilizer Base
5. Stabilizer Bracket
6. Ecocutter (Part No. ECC-125)
7. Saw Base (Part No. 200003)
1.  Using supplied hardware, screw stabilizer base to saw base as shown in Figure 46.
2.  Using supplied bolt, screw top portion of stabilizer to Ecocutter.
Note:  Leave stabilizer bracket screw and wing nut loose at this time.
STABILIZER
Figure-46







Stablizer Assembly (Part No. 200002)   

29
1.  Loosen wing screw on 
the depth indicator of the 
Ecocutter.  (See Figure 47)
2.  Bring Ecocutter down gently 
until blade segments just 
touches rubber table pad. 
(See Figure 48)
 
BLADE HEIGHT ADJUSTMENT
Ecocutter blade height must be properly adjusted for cutting depth befor\
e use.  The following 
steps will ensure proper operation during cutting.
Note:  Incorrect blade height adjustment will result in damage to the bl\
ade and saw base.
Figure-47
Figure-48
Wing Screw   

30
3.  Tighten wing nut to a hand tight 
condition.  (See Figure 49)
4.  Tighten stabilizer bracket bolt with 
wrench to a snug condition.  (See 
Figure 50)
Figure-50
Figure-49