Home
>
Alpha Tool.Com.HK Limited
>
Cutting System
>
Alpha Tool.Com.HK Limited Stone Cutter ECCKIT User Manual
Alpha Tool.Com.HK Limited Stone Cutter ECCKIT User Manual
Have a look at the manual Alpha Tool.Com.HK Limited Stone Cutter ECCKIT User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 67 Alpha Tool.Com.HK Limited manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 6
6
ALPHA® ECOCUTTER STAND (ECC-STAND)
COMPONENTS:
1. 2 Bolts and Hardware (for folding leg assembly) (Part No. 200026)
2. 8 Bolts and Hardware (for casters)
3. 2 Locking Casters
4. 2 Legs (Front Saw Stand, Part No. 200020 — Rear Saw Stand, Part No. 200021)
5. 2 Wing Screws (Part No. 200024)
After removal of all cutting table base components from packing, check f\
or each item listed
below:
Figure-1
(Part No. 200022)](http://img.usermanuals.tech/thumb/326/5168/w64_stone-cutter-ecckit-user-manual-1478733781_d-5.png "Page 6
6
ALPHA® ECOCUTTER STAND (ECC-STAND)
COMPONENTS:
1. 2 Bolts and Hardware (for folding leg assembly) (Part No. 200026)
2. 8 Bolts and Hardware (for casters)
3. 2 Locking Casters
4. 2 Legs (Front Saw Stand, Part No. 200020 — Rear Saw Stand, Part No. 200021)
5. 2 Wing Screws (Part No. 200024)
After removal of all cutting table base components from packing, check f\
or each item listed
below:
Figure-1
(Part No. 200022)")
![Page 7
7
ASSEMBLY OF ECOCUTTER STAND
The following tools will be needed to assemble this base section of the \
cutting table for
the Ecocutter.
2 - 14mm wrenches
1 - 11mm wrench
1 - 10mm wrench
1. Position the two legs to create a scissor
configuration as shown in Figure 2.
Figure-2
2. Turn assembly on its side and align the
holes located at the center of each leg.
Insert one of the two large bolts (Part No.
200026) using a flat washer on each side
followed by the nylon insert lock nut as
shown in...](http://img.usermanuals.tech/thumb/326/5168/w64_stone-cutter-ecckit-user-manual-1478733781_d-6.png "Page 7
7
ASSEMBLY OF ECOCUTTER STAND
The following tools will be needed to assemble this base section of the \
cutting table for
the Ecocutter.
2 - 14mm wrenches
1 - 11mm wrench
1 - 10mm wrench
1. Position the two legs to create a scissor
configuration as shown in Figure 2.
Figure-2
2. Turn assembly on its side and align the
holes located at the center of each leg.
Insert one of the two large bolts (Part No.
200026) using a flat washer on each side
followed by the nylon insert lock nut as
shown in...")
![Page 12
12
ALPHA® ECOCUTTER TABLE (ECC-TABLE)
After removal of all cutting table components from packing, check for ea\
ch item listed
below:
COMPONENTS:
1. Assembled Table (Part No. 200013)
2. Angle Guide Assembly (Part No. 200018)
3. Rip Guide Assembly (Part No. 200017)
4. Hose Holder Assembly (Part No. 200001)
5. Universal Wrench (Part No. 200019)
6. Brush (Part No. 200025)
Figure-13
CAUTION!
WHEN REMOVING ECOCUTTER TABLE FROM CARTON,
DO NOT LIFT BY RAIL TUBE. ALWAYS USE SIDE HANDLE.
See page...](http://img.usermanuals.tech/thumb/326/5168/w64_stone-cutter-ecckit-user-manual-1478733781_d-11.png "Page 12
12
ALPHA® ECOCUTTER TABLE (ECC-TABLE)
After removal of all cutting table components from packing, check for ea\
ch item listed
below:
COMPONENTS:
1. Assembled Table (Part No. 200013)
2. Angle Guide Assembly (Part No. 200018)
3. Rip Guide Assembly (Part No. 200017)
4. Hose Holder Assembly (Part No. 200001)
5. Universal Wrench (Part No. 200019)
6. Brush (Part No. 200025)
Figure-13
CAUTION!
WHEN REMOVING ECOCUTTER TABLE FROM CARTON,
DO NOT LIFT BY RAIL TUBE. ALWAYS USE SIDE HANDLE.
See page...")
![Page 14
14
CAUTION!
NON-RECOMMENDED METHODS
Please note the following illustrations carefully before assembling tabl\
e to stand.
DO NOT LIFT TABLE BY RAIL TUBE.
TABLE WILL BE DAMAGED
IF HANDLED IMPROPERLY.
INSTRUCTIONS ON HANDLING THE ECOCUTTER TABLE
Figure-17](http://img.usermanuals.tech/thumb/326/5168/w64_stone-cutter-ecckit-user-manual-1478733781_d-13.png "Page 14
14
CAUTION!
NON-RECOMMENDED METHODS
Please note the following illustrations carefully before assembling tabl\
e to stand.
DO NOT LIFT TABLE BY RAIL TUBE.
TABLE WILL BE DAMAGED
IF HANDLED IMPROPERLY.
INSTRUCTIONS ON HANDLING THE ECOCUTTER TABLE
Figure-17")
11 ALPHA® ECOCUTTER STAND SCHEMATIC (ECC-STAND) DRAWING NO.PART NO.DESCRIPTIONQUANTITY 1200020Front Saw Stand1 2200021Rear Saw Stand1 3200022Wheel/Brake Assembly 1 4200026Saw Stand Screw Set1 5200024Wing Screw (2 pc set)1 —200023Saw Stand AssemblyALL
12 ALPHA® ECOCUTTER TABLE (ECC-TABLE) After removal of all cutting table components from packing, check for ea\ ch item listed below: COMPONENTS: 1. Assembled Table (Part No. 200013) 2. Angle Guide Assembly (Part No. 200018) 3. Rip Guide Assembly (Part No. 200017) 4. Hose Holder Assembly (Part No. 200001) 5. Universal Wrench (Part No. 200019) 6. Brush (Part No. 200025) Figure-13 CAUTION! WHEN REMOVING ECOCUTTER TABLE FROM CARTON, DO NOT LIFT BY RAIL TUBE. ALWAYS USE SIDE HANDLE. See page 13 for details.
13 INSTRUCTIONS ON REMOVING THE ECOCUTTER TABLE FROM BOX Step 1. Step 2. Figure-14 Figure-15 Figure-16 Step 3. RECOMMENDED METHOD
14 CAUTION! NON-RECOMMENDED METHODS Please note the following illustrations carefully before assembling tabl\ e to stand. DO NOT LIFT TABLE BY RAIL TUBE. TABLE WILL BE DAMAGED IF HANDLED IMPROPERLY. INSTRUCTIONS ON HANDLING THE ECOCUTTER TABLE Figure-17
15 RECOMMENDED METHOD Step 1. Step 2. Figure-18 Figure-19
16 Step 3. Step 4. RECOMMENDED METHOD Figure-20 Figure-21
17 ASSEMBLING TABLE TO STAND 1. Place stand in open position. Set caster wheel locks to the locked position by pressing latch down as shown in Figure 22 and Figure 23. Figure-22 Locked Position Figure-23
18 Wing Screw Clearance Hole Location Pins Stand Figure-26 2. Pick up table by sides and place on stand. Figure-24Figure-25 * Follow the recommended steps on pages 15 and 16
19 3. After placement of the table onto the stand, adjust table so the side extension support slider tube fits outside of the location pins of both sides of the stand as shown in Figure 27. Figure-27 Location Pins Side Extension Support Slider Tube 4. Align wing screw clearance hole with threaded hole of table cross support. (See Figure 28). 5. Insert and tighten wing screw to a hand tight condition as shown in Figure 29. 6. Repeat process for opposite side to complete the stand assembly. Figure-28 Figure-29
20 INSTALLATION OF THE HOSE HOLDER TO THE SAW BASE 1. Position and align the hose holder to the saw base as shown in Figure 30, making note of the threaded hole locations. Saw Base Threaded Holes Hose Holder Figure-30 Figure-31 2. Install supplied phillips screw and washer and hand tighten with screw driver as shown in Figure 31.