Home
>
Alpha Tool.Com.HK Limited
>
Cutting System
>
Alpha Tool.Com.HK Limited Stone Cutter ECC125 User Manual
Alpha Tool.Com.HK Limited Stone Cutter ECC125 User Manual
Have a look at the manual Alpha Tool.Com.HK Limited Stone Cutter ECC125 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 67 Alpha Tool.Com.HK Limited manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 26
26
INNER BELT INSTALLATION
1. Install new belt by rotating and pushing outward onto the pulleys as sho\
wn in
Figure 36.
2. The belt pulley system is self-centering; rotate belt and pulleys togeth\
er for a few
revolutions by hand.
CAUTION!
Belts cannot be tested until inner and outer flanges and flange bolt are installed to hold the
pulley firmly in place, (otherwise, belt and pulley will fly off of the spindle.).
3. Reinstall belt cover and secure with phillips screw.
4. Replace side...](http://img.usermanuals.tech/thumb/326/5169/w64_stone-cutter-ecc125-user-manual-1478733842_d-25.png "Page 26
26
INNER BELT INSTALLATION
1. Install new belt by rotating and pushing outward onto the pulleys as sho\
wn in
Figure 36.
2. The belt pulley system is self-centering; rotate belt and pulleys togeth\
er for a few
revolutions by hand.
CAUTION!
Belts cannot be tested until inner and outer flanges and flange bolt are installed to hold the
pulley firmly in place, (otherwise, belt and pulley will fly off of the spindle.).
3. Reinstall belt cover and secure with phillips screw.
4. Replace side...")
![Page 27
27
OUTER BELT REMOVAL
DANGER!
Be sure to unplug the power cord from the outlet before assembling or di\
sassembling the
tool. Accidental starting of the motor may cause bodily injury.
1. Locate outer cover (left front side of the tool) as shown in Figure 38\
.
2. Loosen the bolt knob and remove outer cover to expose the outer belt as shown in
Figure 39.
Outer Cover
Bolt Knob
Figure-39
Figure-38
3. Rotate belt while pulling in a outward motion to remove from pulleys as \
shown in
Figure 40 and...](http://img.usermanuals.tech/thumb/326/5169/w64_stone-cutter-ecc125-user-manual-1478733842_d-26.png "Page 27
27
OUTER BELT REMOVAL
DANGER!
Be sure to unplug the power cord from the outlet before assembling or di\
sassembling the
tool. Accidental starting of the motor may cause bodily injury.
1. Locate outer cover (left front side of the tool) as shown in Figure 38\
.
2. Loosen the bolt knob and remove outer cover to expose the outer belt as shown in
Figure 39.
Outer Cover
Bolt Knob
Figure-39
Figure-38
3. Rotate belt while pulling in a outward motion to remove from pulleys as \
shown in
Figure 40 and...")
![Page 28
28
OUTER BELT INSTALLATION
1. Before new belt installation; clean the two pulleys and surrounding area\
s.
Belt pulleys must be clean from dirt and grease before new belt installa\
tion (to prevent
slippage).
2. Install the new belt by rotating and pushing outward onto the pulleys as\
shown in
Figure 42.
3. The belt pulley system is self-centering, rotate belt and pulleys togeth\
er for a few
revolutions by hand.
CAUTION!
Belts cannot be tested until inner and outer flanges and flange...](http://img.usermanuals.tech/thumb/326/5169/w64_stone-cutter-ecc125-user-manual-1478733842_d-27.png "Page 28
28
OUTER BELT INSTALLATION
1. Before new belt installation; clean the two pulleys and surrounding area\
s.
Belt pulleys must be clean from dirt and grease before new belt installa\
tion (to prevent
slippage).
2. Install the new belt by rotating and pushing outward onto the pulleys as\
shown in
Figure 42.
3. The belt pulley system is self-centering, rotate belt and pulleys togeth\
er for a few
revolutions by hand.
CAUTION!
Belts cannot be tested until inner and outer flanges and flange...")
![Page 33
33
SERVICES AND WARRANTY INFORMATION
LOANER PROGRAM
Loaner tools can be issued to temporarily replace a tool that is being r\
eturned to Alpha®
for repair. If more than one tool is being returned for repair, the number of loaner tools
provided will be based on availability.
If a loaner tool is required, contact Alpha® Tool Department at (800) 648-7229 to receive a
Loaner Tool Application. A valid credit card number must be provided as a security deposit.
The credit card will only be...](http://img.usermanuals.tech/thumb/326/5169/w64_stone-cutter-ecc125-user-manual-1478733842_d-32.png "Page 33
33
SERVICES AND WARRANTY INFORMATION
LOANER PROGRAM
Loaner tools can be issued to temporarily replace a tool that is being r\
eturned to Alpha®
for repair. If more than one tool is being returned for repair, the number of loaner tools
provided will be based on availability.
If a loaner tool is required, contact Alpha® Tool Department at (800) 648-7229 to receive a
Loaner Tool Application. A valid credit card number must be provided as a security deposit.
The credit card will only be...")
31 ALPHA® ECOCUTTER PARTS LIST (ECC-125) DRAWING NO.PART NO.DESCRIPTIONQUANTITY 34133530Anti-Back-Flow Flap1 35133047Cable Sleeve1 36133452/133547Rated Plate 110V/220V1 37133475/133546Breaker Assembly (w/cord)110V/220V1 38133474Cord (w/o breaker)110V1 39133533Dust Hose1 40133532Dust Bag Holder1 42133544Dust Bag w/Strap 17”x13 1-/2” x12”1 43133503Pulley (Outside) 21mm OD LHT Fan1 44133502Felt Rings D19xD12xT23 45133492Bearing 698 2RS4 46133498Spacer D12xd8.5x4T1 47133511Knob Bolt1 48133500Bearing Housing1 50133508Outer Belt 10 x 209mm1 51133488Pulley (Outside) 24mm OD RHT1 52133495Fan1 55133496Fan Shaft1 56133486Housing Adapter1 57133483Main Housing1 58801086Side Handle (for AWS-125/ECC-125)1 59133522Screws M4x155 60133490Pulley (Inside) 18mm OD RHT1 63133487Pulley Shaft1 64133513Screw M4x254 65133545Screw M5x401 66133386Gear Housing1 67133058Gear (Big)1 68133066Needle Bearing Bk 08101 69133368Gear Housing1 70133067O Ring 25.5×21 71133512Screw M5x153 72133529Sleeve1
32 ALPHA® ECOCUTTER PARTS LIST (ECC-125) DRAWING NO.PART NO.DESCRIPTIONQUANTITY 73133510Outer Cover1 74133053Bearing 6201-2RS1 75133060Screw Cap1 76133062O Ring 18×2.51 77133481Spindle (for ECC-125)1 78133506Pulley (Inside) 36mm OD Spindle1 79133509Inner Belt 10 x 230mm1 80133514Inner Cover1 81133515Screw M5x30 (use part #133513)1 82133521Side Cover1 83133519Flange Bolt1 84133518Flange Outer (for ECC-125)1 85133516Flange Inner (for ECC-125)1 86133071Flat Washer M61 87133084Wing Screw3 88133269Washer For Ruler2 89133528Guide Pin1 90130798Retaining Rings -E1 91133527TT Ruler Guide (for ECC-125)1 92133523Base Plate Assembly1 93133072Spring Washer M6 1 95133535Wrench (for ECC-125)1 96133534Hexagon Ring Spanner1 97133369Felt Strip Set2 98133615Felt Rings D26.6xD12.5xT21 99133616Dust Shield D43xD23xT0.351 100133696Inner Cover Gasket (for ECC-125)1 (not shown)133536BMC (Blow Mold Case) for ECC-1251
33 SERVICES AND WARRANTY INFORMATION LOANER PROGRAM Loaner tools can be issued to temporarily replace a tool that is being r\ eturned to Alpha® for repair. If more than one tool is being returned for repair, the number of loaner tools provided will be based on availability. If a loaner tool is required, contact Alpha® Tool Department at (800) 648-7229 to receive a Loaner Tool Application. A valid credit card number must be provided as a security deposit. The credit card will only be charged if the loaner tool is not returned to Alpha® within 30 days. An authorized signature is required for the credit card being used. A second signature is required as an agreement of the overall policy. NEED MORE INFORMATION For information on Alpha Professional Tools® complete product line, visit us on the web at www.alpha-tools.com Limited Warranty of Alpha® Ecocutter in the USA and Canada ONLY!Alpha Professional Tools® warrants this product against defects in material and workmanship for a period of 180 days from the date of original retail purchase (proof of purchase required). If Alpha Professional Tools® receives notice of such defects during the warranty period, our obligation assumed under this warranty is limited to the repair or replacement of parts, without charge. This warranty does not apply to tool accessories. For Warranty Claims: Send complete tool with all your information and details of the problem to the address printed on the cover of this manual, transportation prepaid. Do not send tool accessories. WARRANTY
34
EC DECLARATION OF CONFORMITY
Name of Manufacturer: Alpha Professional Tools®
Address of Manufacturer: 103 Bauer Drive
Oakland, NJ 07436
USA
Herewith declares that:
ELECTRIC HAND TOOL: “Ecocutter”
Make: Alpha Professional Tools®
Type: ECC-125/ECC-225
-Does comply with the provisions of the Low Voltage Directive 73/23EEC amended by
93/68 EEC and Machinery Directive 98/37/EC.
And furthermore declares that:
-The following (parts/clauses of) harmonized standards have been appli\
ed:
EN55014-1/ + A1: 2001, EN55014-2/ + A1: 2001, EN61000-3-2:2000, EN61000-3-
3/+A1:2001.
Year of affix CE Marking: 2005
Oakland, New Jersey USA
Nao Takahashi
(President)
35 Photocopy of product registration form will be accepted. PRODUCT REGISTRATION CARD Model No. Serial No. Company Name: ______________________________________________ Name: ______________________________________________________ Address: ____________________________________________________ City: _______________________State: ________Zip: ________________ Telephone: ___________________________________________________ Purchase Date: _______________________________________________ Dealer’s Name: _________________________________ Note: Serial & Model Number must be included for proper registration. (800) 648-7229 Mail or Fax to: Alpha Professional Tools® 103 Bauer Drive, Oakland, NJ 07436 Fax: 800-286-0114 Register online at: www.alpha-tools.com/productregistration.aspx
Copyright © 2010 Alpha Professional Tools. All rights reserved. 103 Bauer Drive, Oakland, NJ 07436 • 800-648-7229 • Fax: 800-286-0114www.alpha-tools.com 2/28/13