Alpha Tool.Com.HK Limited Stone Cutter ECC125 User Manual

Part No: ECC-125/ECC-225
Version 5
Alpha® Ecocutter
Instruction Manual
MANUAL
103 Bauer Drive, Oakland, NJ 07436 • 800-648-7229 • Fax: 800-286-0114
www.alpha-tools.com 

2
TABLE OF CONTENTS
Introduction ........................................................................\
.......................................3
 About The Symbols ........................................................................\
.....................3
 Safety Instructions   ........................................................................\
.....................3
 For Safe Operation ........................................................................\
.......................3...

3
INTRODUCTION
Thank you for purchasing the Alpha® Ecocutter Dry Tile Cutting System.  Please read this 
instruction manual thoroughly to ensure safe and correct use of the Ecocutter Dry Tile Cut-
ting System.   Keep this manual in a place where operators can access it easily whenever 
necessary.
 ABOUT THE SYMBOLS
According	to	the	 hazard	 level,	all	safety	 notes	in	this	 manual	 are	classified	 into	“DANGER”, 		
“WARNING”,	and	“CAUTION”.
    DANGER!  Death or serious personal injury is imminent when...

4
2. Consider work area environment
 Do not expose power tools to rain. Do not use power tools in damp or wet locations 
without GFCI protection.  Keep work areas well lit. Do not use the tool \
in presence of 
flammable	liquids	or	gases.
3. Guard against electric shock
 Prevent body contact with grounded surfaces. For example: pipes, radiato\
rs, ranges, 
and refrigerator enclosures; use grounded outlets. 
4. Keep children and visitors away
 Do not let visitors contact tool or extension cord.  All...

5
15. Remove adjusting keys and wrenches
 Check to see that keys and adjusting wrenches are removed from the tool \
before 
turning it on.
16. Avoid unintentional starting
	 Do	 not	carry	 a	plugged-in	 tool	with	 finger	 on	switch.	 Be	sure	 the	switch	 is	off	 when 	
plugging in.
17. Outdoor use extension cords
 When tool is used outdoors, use only extension cords intended for use ou\
tdoors and 
so marked.
18. Stay alert
 Use caution and do not operate tool when you are tired or on medication.\
19....

6
  SPECIFICATIONS
Rating ........................................................................\
...............110/220 Volts
Amperage ........................................................................\
...................11.2/5.5
Power ........................................................................\
...........................1200W
No-load Speed (min-1) ...............................................................12,000 RPM
Weight...

7
 ACCESSORIES



COMPONENTS: 
1. Dust Hose (Part No. 133533)
2. Dust Gate w / Anti-back Flow Flap (Part Nos. 133531 / 133530)
3.  Side Handle (Part No. 801086)
4.  Hexagon Ring Spanner (Part No. 133534)
5. Wrench (Part No. 133535)
6. Dust Bag (Part No. 133544)
7. TT Ruler Guide (Part No. 133527)
8. Hook and Loop Strap (2 pcs) (Part No. 133551)


Figure-2   

8
 MAIN CONNECTION
Connect	Ecocutter	 to	a	single	 phase	AC	current	 supply	and	to	the	 main	 voltage	 specified 	
on the cutter’s rating plate.
 SWITCHING ON AND OFF
Intermittent use:
Switching on:  Press switch trigger
Switching off:  Release switch trigger
Continuous use:
Switching on:  Press the switch trigger and then the locking button; rel\
ease on/off switch
Switching off:  Press the switch trigger and then release
CIRCUIT BREAKER
  CAUTION!
If the tool stops during operation you need to switch...

9
The Ecocutter is supplied with an in-line circuit breaker.  In the event that the breaker is 
tripped, push the button to reset.  Once you are able to reset the circuit breaker, run the tool 
in a no load condition allowing air to pass over the motor and cool it d\
own.
BEFORE USE
  DANGER!
Before using the machine, check the following items.  In particular, check items 1 to 5 before 
plugging the power supply cord into the power outlet.
1. Check the working voltage.
–	 Be	 sure	the	voltage	 specified...

10
4. Inspect the saw blade.
–	 Check	if	you	have	a	specified	blade.
– Never use cracked, chipped, or any damaged blades.
–	 Follow	 the	procedures	 specified	in	the	 instruction	 manual	to	properly	 attach	
applicable accessories.
5. Check the power outlet.
–  When the plug of the power supply cord is easily pulled out of the power outlet, 
the outlet should be replaced.  For such tasks, consult an electrician.  If the power 
outlet is used on a continuous basis, it may overheat and cause accidents. 
6....