Alinco DJ-x2t/e Wide Band Communication Receiver Instruction Manual

31
3
Operating in Expert Mode
3Select a bank by pressing the [10MHz (BANK)] key.
Every press of the [10MHz (BANK)] key changes the bank at the upper left
on the display as shown below.
0 Ý1 Ý2 ··· Ý9 ÝA ÝP ÝJ Ý0 ···
Each bank No. corresponds to the following bank.
0 - 9 : For Memory channel
A, B : For Program scan channel
P : For Priority channel
J : For Search-pass memory channel
Select a bank according to the use.
4Select a channel by pressing the [s / t] keys.
According to the type of bank, available...

3
Operating in Expert Mode
32
nSelecting a channel
To call up a frequency programmed in a channel:
1Switch to the Memory mode by pressing the [V/P/M (MW)] key.
2Select a bank by pressing the [10MHz (BANK)] key.
3Select a channel by pressing [s / t] keys.
It is not possible to select a channel which is not programmed.
nClearing a channel
To clear a channel:
1Switch to the Memory mode by pressing the [V/P/M (MW)] key.
2Select a channel which you want to clear.
3Press the [FUNC/ENTER] key.
F will appear on...

33
3
Operating in Expert Mode
Setting the Antenna
You can select the antenna depending on the frequency you wish to receive.
The DJ-X2 has three types of antennas.
External antenna ···························The SMA antenna attached to the DJ-X2.
Earphone antenna·························The earphones cord performs the role of
antenna.
Bar antenna···································The internal antenna which receives AM
radio. (DJ-X2T: 530 kHz - 1710 kHz (step:
10 kHz), DJ-X2E: 522 kHz - 1620 kHz (step:
9...

3
Operating in Expert Mode
34
nWhen receiving AM radio
At steps 1 and 2 mentioned on the previous page, bAr on/oF (which shows
the status of the bar antenna) appears on the display.
bAr on : Receives with the bar antenna.
bAr oF : Receives with the external antenna or earphone antenna.
(The default setting is ON.)
Pressing the [FUNC/ENTER] key completes the setting.
Selecting the Modulation Mode
You can select a modulation mode from AM, FM, and WFM.
To select :
1Press the [FUNC/ENTER] key.
F will appear...

35
3
Operating in Expert Mode
Setting the Tuning Step
The tuning step sets the increment/decrement of each press of the [s / t]
keys when adjusting the frequency in VFO mode.
To set the tuning step:
1Switch to VFO mode by pressing the [V/P/M (MW)] key.
2Press the [FUNC/ENTER] key.
F will appear on the display.
3Press the [PS (STEP/SKIP)] key.
The currently selected tuning step will appear on the display. The default
setting is AUTO.
4Select a tuning step by pressing the [s / t] keys from the followings....

3
Operating in Expert Mode
36
Memory Skip
This function is for skipping the specified memory channel(s) when executing
the Memory scan.
To set the memory channel which you want to skip:
1Switch to Memory mode by pressing the [V/P/M (MW)] key.
2Call up the memory channel you want to skip.
3Press the [FUNC/ENTER] key.
F will appear on the display.
4Press the [PS (STEP/SKIP)] key.
The setting will be completed.
How do you cancel the memory skip?
Call up the memory channel to cancel, and then operate steps 3...

37
3
Operating in Expert Mode
Descrambling
This function returns scrambled voice to normal reception.
To descramble:
1Select the frequency of the scrambled voice.
2Press the [FUNC/ENTER] key.
F will appear on the display.
3Press the [MONI (SCRT)] key.
Descrambling function starts operating, and l at the upper left of the dis-
play flashes.
Decode No. for scrambling will appear on the display. 
You can change the decode No. by pressing the [s / t] keys.
4Select a decode No. by pressing the [s / t] keys....

3
Operating in Expert Mode
38
Operational Settings
This function allows you to customize the DJ-X2 for your particular application.
The following items can be set in the setting mode.
ATT (Attenuator) function (P.39)
Bank link setting (P.39)
Beep function (P.40)
Lamp  function (P.40)
Timer scan/Busy scan setting (P.41)
BS (Battery save) function (P.41)
APO (Auto power off) function (P.42)
Bugging detector sensitivity setting (P.42)
OV (Overwrite) setting (P.43)
PRIO (Priority) Watch (P.43)
nSetting each...

39
3
Operating in Expert Mode
nATT (Attenuator) function
This function attenuates strong signals on nearby channels.
Use this function when the received signal is influenced by a strong signal.
ATT function attenuates about 20 dB in received signal. 
Select Att in the setting mode.
· Select ON/OFF by pressing the [s / t] keys.
· The default setting is OFF.
nBank link setting
This is the setting for the Bank link scan, which scans specified multiple
banks.
You can select up to 5 banks from 10 programmed...

3
Operating in Expert Mode
40
nBeep function
The beep sound which sounds when operating keys on the DJ-X2 can be
turned OFF.
Select bEEP in the setting mode.
· Select ON/OFF by pressing the [s / t] keys.
· The default setting is ON.
nLamp function
This function sets the display backlight ON or OFF.
When ON is selected, an operation of any key turns ON the backlight, and it
automatically turns OFF after 5 seconds.
Select LP in the setting mode.
· Select ON/OFF by pressing the [s / t] keys.
· The default...