Alinco DJ-x2t/e Wide Band Communication Receiver Instruction Manual

41
3
Operating in Expert Mode
nTimer scan/Busy scan setting
You can set the scan-resume condition.
While executing the scan, if the DJ-X2 receives a signal, scanning will pause.
You can set the timing that the DJ-X2 restarts scanning. 
Timer scan (tIMEr)·························Restarts after five-second stop, even while
still receiving a signal.
Busy scan (bUSy) ·························Restarts when the DJ-X2 does not receive a
signal.
Select tIMEr or bUSy in the setting mode.
· Select Timer/Busy scan...

3
Operating in Expert Mode
42
nAPO (Auto power off) function
This function automatically turns the power OFF if there is no key operation for a
specified period of time.
Select the time from 30, 60, 90 minutes, and OFF. When OFF is selected, this
function does not work.
Select APO in the setting mode.
· Select ON/OFF by pressing the [s / t] keys.
· The default setting is OFF.
· APO function does not work while scanning.
nBugging detector sensitivity setting
You can select the sensitivity when detecting a...

43
3
Operating in Expert Mode
nOV (Overwrite) setting
To prevent from overwriting a memory channel by mistake, set the Overwrite set-
ting.
Select ov in the setting mode.
· Select ON/OFF by pressing the [s / t] keys.
ov  on : Overwriting enabled
ov  oF : Overwriting disabled
· The default setting is OFF.
nPRIO (Priority) watch
This function monitors two frequencies alternately. 
Every five seconds, the DJ-X2 momentarily switches from the frequency in the
VFO mode to the frequency in the priority...

4
Chapter Appendices
4
Appendices
44
Troubleshooting
Please check the list below before concluding the DJ-X2 is faulty. If a problem
persists, reset the DJ-X2. This can sometimes correct erroneous operation.
Symptom Possible Cause Action
Recharge or exchange batter-
ies.
Check the position of battery 
selection switch.
Adjust the volume.
Remove the earphone.
Adjust the squelch level or 
turn OFF. Or press the [MONI 
(SCRT)] key.
Adjust the squelch level or 
turn OFF. 
Turn the attenuator OFF.
Check the...

45
4
Appendices
Specifications
nGeneral
Receiving range E : 0.522 - 999.995 MHz
T : 0.530 - 823.995 MHz
850.000 - 868.995 MHz
895.000 - 999.995 MHz
Modulation modes : FM, WFM, AM
Ant. impedance : 50½
Ant. terminal : SMA
Supply voltage : DC 3.8V (internal lithium-ion battery)
DC 4.5V (when using EDH-27)
Ground : Negative ground
Current consumption : Reception: approx. 80 mA
Battery save (1 : 4): approx. 25 mA
Temperature range : –10 - +60°C (+14 - +140°F)
Frequency stability : ±5 ppm (–10 - +60°C) (+14 -...

4
Appendices
46
Operation Chart
Function Key Operation Page
P.15
P.15
P.18
P.16
P.19
P.19
P.20
P.21
P.29
P.17
P.18
P.32
P.30
P.33
P.34
P.35
P.36 [VOL/SQL] key, Adjust by [s/t] 
keys
[VOL/SQL] key, Adjust by [s/t] 
keys
[s/t]  keys
[1MHz (ANT)]+[s/t] keys
[10MHz (BANK)]+[s/t] keys
[MONI (SCRT)] key
[SCAN (MODE)] key
[SCAN (MODE)] key
[PS (STEP/SKIP)] key
Select by [s/t] keys, then [PS 
(STEP/SKIP)] key to start
[SCAN (MODE)] key
Select by [s/t] keys, then [SCAN 
(MODE)] key to start
Hold down [V/P/M (MW)]...

47
4
Appendices
Function Key Operation Page
P.24
P.37
P.37
P.38
P.38
P.38
P.25
P.25
P.23
P.26 [FUNC/ENTER] key for a second
[FUNC/ENTER]+[MONI (SCRT)] keys
[s/t] keys
[FUNC/ENTER]+[VOL/SQL (SET)] 
keys
[VOL/SQL (SET)] key
[s/t]  keys
Fix by [FUNC/ENTER] key
Hold down [FUNC/ENTER] key 
and Power ON
[s/t] keys
Reset by [FUNC/ENTER] key
Hold down [MONI (SCRT)] key and 
Power ON
[VOL/SQL (SET)] key+Power ON, 
Start by [s/t] key Keylock ON/OFF
Descrambling ON/OFF
Changing the decode No. of 
descrambling...

memo