Alfa Router AIP-W610 User Manual

option steps first. 
 
1. Select a location with access for cables and a power outlet. 
2.  Unplug the unit. Place it upside down on a flat surface and mark the two holes for 
anchors. 
3.  Installing the Wall mount anchor (plastic) into the wall with tools such as drill or 
hammer. 
4.  Insert the provided screws in each hole of the stand parts. 
5.  Attaches the unit to the anchors on the wall. 
 
Stand Option 
 
1.  The Router includes two stand parts. 
2.  Combine two parts into one stand. Combine...

Installing And Using Wireless Router 
     
This Chapter provides a step-by-step guide to the installation and 
configuration of the Wireless Router. We suggest you go over the whole 
chapter and then do more  advanced operation.   
 
Network configuration setup 
 
Steps to build up the network: 
  
¾ Connect the ADSL or Cable modem to  the Ethernet WAN port on the back of 
the Wireless Router by using the UTP cable.   
¾  Connect the phone line from the wall socket to the line-in port on the ADSL...

Computer configuration setup 
 
In order to communicate with this Wireless Router, you have to configure the IP 
addresses of your computer to be compatible with the device. The router supports 
DHCP server and it is enabled as default. Users that configure your IP address as 
“Obtain an IP address automatically” may skip the following IP configuration 
instruction. 
 
Note:  
1.   The default network setting of the device: 
  IP address:    192.168.1.1 
 Subnet Mask:  255.255.255.0 
 DHCP Server:...

9 
  

3. Choose  Internet Protocol (TCP/IP)  and click Properties.   
 
 
 
4.  You may choose “Obtain an IP address automatically”(recommend) to get IP 
address automatically or choose “Use the following IP address” to specify IP addresses 
manually. Please click the OK button after your configuration. 
 
10 
 
  

 Management 
Wireless Router configuration setup 
 
In order to make the whole network operate successfully, it is necessary to 
configure the Wireless Router through your computer has a WEB browser 
installed. Please follow up the steps listed below. 
 
1. Double click the Internet WEB browser icon on your desktop screen 
(Netscape Communicator 4.0 and Internet Explorer 3.0 or update version) 
 
2.  Type 192.168.1.1 into the URL WEB address location and press Enter. 
 
  
3.  The Username and Password...

4. The Graphic User Interaface 
 
After the password authorization, the Setup Wizard shows up as the home page of 
the Graphic User interface. You may click on each folder on left column of each 
page to get access to each configuration page. 
 
 
12 
 
  

Setup Wizard 
 
If you are using the router for the first time, you may follow the procedures of the setup 
wizard to do a step-by-step configuration.   
 
Note: The following instruction does an overall introduction to the Setup Wizard. For detail 
information to each item, please refer to instruction of each page. 
 
1.  To start the Setup Wizard, click the “Next” button to proceed. 
 
2.  Select your demanding operation mode and click “Next”.   
13 
 
  

3.  Mark the check box to enable synchronizing time by NTP server. Select the religion 
you live and a NTP server by clicking the drop list then click “Next”. 
 
 
4.  Specify an IP address and subnet mask for connecting to the router in LAN.     
14 
 
  

5.  Select a WAN access type for the router to co nnect to Internet. Fill in the parameters 
that required in each blank, and then click the “Next” button. You may get those 
parameters from your ISP.     
 
6.   Select the wireless parameters that are used for associating with this router and 
click  “Next”  
15