Alfa Router AIP-W610 User Manual

Port forwarding 
The Port Forwarding allows you to re-direct a particular range of service 
port numbers (from the Internet/WAN Ports) to a particular LAN IP 
address. It helps you to host some servers behind the router NAT firewall. 
 
Configuration  
1.   Click the check box of “Enable port forwarding” to 
enable the function. 
2.  Enter the specific IP address (EX 10.10.10.10), 
Protocol (UDP/TCP), Port range (EX 25-110), and 
comment (EX. E-Mail) 
STEPS 
3.  To Delete the IP address on the table,...

URL Filtering 
The URL Filter allows users to prevent certain URL from accessing by 
users in LAN. This filter will block those URLs that contain certain 
keywords.  
 
 
Configuration  
1.  Click the check box of “Enable URL Filtering” to 
enable the function. 
2.  Enter the URL that is going to be banned. 
STEPS 
3.  To Delete the URL on the table, Click the check box 
in the select item and click the “Delete Selected”. If 
you want to delete all URLs on the table, click 
“Delete All” to remove all of...

38 
Virtual DMZ 
The virtual DMZ is used to enable protocols, which need to open ports on 
the router. The router will forward all unspecified incoming traffic to the 
host specified in this page.   
 
 
To configure it, enter the Host IP (private IP address) and Click 
“Apply changes” to enact the setting. 
  

VPN Setting 
VPN (Virtual Private Network) construct a virtual tunnel to a remote network, 
which prevents the connection from peeping and inspection. The data is 
encrypted with the encryption algorithm  that you specified. To start 
configuring VPN, please mark the  “Enable IPSPEC VPN” check box before 
any configuration. 
 
Enable IPSEC VPN Mark this check box to enable VPN function of the device.   
Enable NAT 
Traversal Click this check box to perform NAT traversal.   
Generate Show 
RSA Key...

VPN parameters configuration 
 
After clicking the “Edit” button, you may configure this VPN tunnel. 
40 
Enable Tunnel 1 Mark this checkbox to enable this VPN tunnel and clear it to 
uncheck it.   
Connection Name Specify a name for this connection. 
Auth Type Select an authentication method for this VPN form the drop 
list.  
Local Site Specify the local network information. 
Remote Site Specify the remote network information. 
Local /Peer ID Select an information ty pe for identification.  
  

Key Management IKE: Mark this check box to enab le IKE. IKE (Internet Key 
Exchange) is a key exchange and authentication protocol 
used by IPsec. You may also click the  “Advanced” button to 
do more advanced configuration for IKE. 
Connection Type:  Select a connection  to be a initiator in 
this VPN or a responder.     
ESP:  Select the encryption and authentication algorithm 
form the drop list.   
Pre-Shared Key: Specify a pre-shared key for this VPN 
after selecting “PSK” in the “Auth Type” drop...

Management 
Status 
In the home page of the Wireless Router, the left navigation bar shows the 
options to configure the system. In the right navigation screen is the 
summary of system status for viewing the configurations. 
 
z   System 
Uptime The period that you power the device on. 
Firmware Version The version of the firmware applied on this device. 
42 
z  Wireless Configuration 
  

Mode The operation mode of the wireless router 
Band The performing band of this wireless router 
SSID The name of this wireless network 
Channel Number The channel used by the wireless LAN. All 
devices in the same wireless LAN should user 
the same channel 
Encryption The security encryption status of this wireless 
network 
BSSID The Basic Service Set Identity of this router.(This 
parameter is the same as the MAC address of 
LAN port) 
Associated Clients The number of associated clients. 
 
z  LAN...

Statistics 
On this page, you can monitor the sent & received packets counters of 
wireless, Ethernet LAN, and Ethernet WAN. To see the latest report, click 
refresh button.   
 
DDNS 
 
This page allows users to connect to DDNS. To enable DDNS, Mark the 
“Enable DDNS” checkbox. Select the service provider from the drop list. Fill 
in domain name, username, and password. Click the “Apply Change” button 
after configuration. 
 
44 
 
  

 
Time Zone Setting 
This page allows users to configure the time of the router. To specify 
manually, fill in the blanks in “Current Time” and click the “Apply Change” 
button. To synchronize time from a timeserver, please mark the “Enable NTP 
client update” checkbox, select a NTP server from the drop list or manually 
enter a NTP server. Click the “Apply Change” button after your configuration.     
 
45