Alfa Router AIP-W610 User Manual

							
option steps first. 
 
1. Select a location with access for cables and a power outlet. 
2.  Unplug the unit. Place it upside down on a flat surface and mark the two holes for 
anchors. 
3.  Installing the Wall mount anchor (plastic) into the wall with tools such as drill or 
hammer. 
4.  Insert the provided screws in each hole of the stand parts. 
5.  Attaches the unit to the anchors on the wall. 
 
Stand Option 
 
1.  The Router includes two stand parts. 
2.  Combine two parts into one stand. Combine it with the side of router near the power 
port. Push the stand up to snap it into place. 
3.  Place the Router. 
 
Restore Default Button 
 
1.   Push the button for more than 5 seconds and then release it, the 
system will return to factory defaul t setting. In the meantime, system 
rewrites flash to default value and Status LED halts for a while. 
Approximately 60 seconds later, the Status LED blinks green 
periodically, now the whole system parameters have returned to 
factory default value. If the process has been interrupted by any 
reason (power off…), the system  will fail. Before performing the 
process, ensure a safe operating environment please ！ 
2.  To reboot the Router, Press the button for 2-5 seconds and then 
release it, and all the setting won’t be erased. Wait for the Router to 
complete the reboo t, and then you can start to use it. 
 
6 
Warning：Incomplete factory setting reco very procedure will cause the 
Wireless Router malfunction！If you are unfortunately in this 
situation, do not try to repair it  by yourself. Consult your local 
distributor for help ！ 
  
						

							
Installing And Using Wireless Router 
     
This Chapter provides a step-by-step guide to the installation and 
configuration of the Wireless Router. We suggest you go over the whole 
chapter and then do more  advanced operation.   
 
Network configuration setup 
 
Steps to build up the network: 
  
¾ Connect the ADSL or Cable modem to  the Ethernet WAN port on the back of 
the Wireless Router by using the UTP cable.   
¾  Connect the phone line from the wall socket to the line-in port on the ADSL 
modem, or the coaxial cable to the line-in port on the Cable modem.   
¾  Plug-in the power adapter to the modem  and turn on the power. Install the 
Ethernet card into the computer by referr ing to the User Guide that came with 
the card. 
¾  Connect the computer to the Wireless  Router by using standard twisted-pair 
Ethernet cable from the computer’s Et hernet card to an 10/100Mbps Ethernet 
port on the back of the Wireless Router.   
7 
¾  Plug-in the power adapter to the Router  and the other side to the wall outlet. 
  
						

							
Computer configuration setup 
 
In order to communicate with this Wireless Router, you have to configure the IP 
addresses of your computer to be compatible with the device. The router supports 
DHCP server and it is enabled as default. Users that configure your IP address as 
“Obtain an IP address automatically” may skip the following IP configuration 
instruction. 
 
Note:  
1.   The default network setting of the device: 
  IP address:    192.168.1.1 
 Subnet Mask:  255.255.255.0 
 DHCP Server:    enabled 
 
2.  In the following TCP/IP configuration guide, the IP address “192.168.1.2 ” is 
assumed to be your IP address if you want to specify IP addresses manually. 
Please  DO NOT  choose 192.168.1.1 for the IP address (192.168.1.1) has been 
set as the default IP  for this device.   
3.  The following TCP/IP configuration guide uses windows XP as the presumed 
operation system. 
 
Procedures to configure IP addresses for y our computer 
 
1.  If you are in Classic Start menu view, click  StartÆSettingsÆ Control 
Panel ÆNetwork Connections . 
If you are in Start menu view, click Start ÆControl Panel Æ Network Connections.  
2.  Double click “ Local Area Connection ” 
 
 
8 
 
  
						

							
9 
  
						

							
3. Choose  Internet Protocol (TCP/IP)  and click Properties.   
 
 
 
4.  You may choose “Obtain an IP address automatically”(recommend) to get IP 
address automatically or choose “Use the following IP address” to specify IP addresses 
manually. Please click the OK button after your configuration. 
 
10 
 
  
						

							
 Management 
Wireless Router configuration setup 
 
In order to make the whole network operate successfully, it is necessary to 
configure the Wireless Router through your computer has a WEB browser 
installed. Please follow up the steps listed below. 
 
1. Double click the Internet WEB browser icon on your desktop screen 
(Netscape Communicator 4.0 and Internet Explorer 3.0 or update version) 
 
2.  Type 192.168.1.1 into the URL WEB address location and press Enter. 
 
  
3.  The Username and Password Required window appears. 
-  Enter  admin  in the User Name location (default value). 
- Enter  admin  in the Password location (default value). 
- Click  “OK”  button 
 
 
11 
 
  
						

							
4. The Graphic User Interaface 
 
After the password authorization, the Setup Wizard shows up as the home page of 
the Graphic User interface. You may click on each folder on left column of each 
page to get access to each configuration page. 
 
 
12 
 
  
						

							
Setup Wizard 
 
If you are using the router for the first time, you may follow the procedures of the setup 
wizard to do a step-by-step configuration.   
 
Note: The following instruction does an overall introduction to the Setup Wizard. For detail 
information to each item, please refer to instruction of each page. 
 
1.  To start the Setup Wizard, click the “Next” button to proceed. 
 
2.  Select your demanding operation mode and click “Next”.   
13 
 
  
						

							
3.  Mark the check box to enable synchronizing time by NTP server. Select the religion 
you live and a NTP server by clicking the drop list then click “Next”. 
 
 
4.  Specify an IP address and subnet mask for connecting to the router in LAN.     
14 
 
  
						

							
5.  Select a WAN access type for the router to co nnect to Internet. Fill in the parameters 
that required in each blank, and then click the “Next” button. You may get those 
parameters from your ISP.     
 
6.   Select the wireless parameters that are used for associating with this router and 
click  “Next”  
15