Aleratec 15 HDD Copy Cruiser HighSpeed WL User Guide

www.aleratec.com35
Stand-Alone D\fplicat\Bor SA: T\ftorials
Note: If the number of bl\bank di\bc\b you in\berte\bd doe\bn’t match the\b 
number of di\bc\b dete\bcted on the \bcreen,\b plea\be give 10-15 \b\becond\b 
for the duplicator \bto recognize all of\b your blank di\bc\b.
e. After 2 or 3 seconds of processing time, the following Copy Progress 
Screen will appear.
Note: It i\b normal to \bee\b the progre\b\b indica\btor \btay at 0-10% a\bnd at 
100% for approximat\bely 30 \becond\b durin\bg CD...

www.aleratec.com36
Stand-Alone D\fplicat\Bor SA: T\ftorials
How to Make Copies fr\Bom the Hard Drive - continued
Next, refill more blank media to continue making more copies, or you can press 
ESC to terminate your project and go back to the main menu.
If you’ve specified a counter value for your project and your project is 
completed, you will see the following screen:
If you see above message, you can press ENT to go back to main menu.
Note: If you enabled the\b counter and the n\bumber of di\bc\b you...

www.aleratec.com37
Stand-Alone D\fplicat\Bor SA: T\ftorials
Select B\frn Speed
This process will allow you to adjust the duplication speed subject to your various 
needs.
By default, the duplication speed will be set to the optimal speed. However, 
under some circumstances, you might want to lower the duplication speed.  Those 
circumstances are as follows:
• Poor Blank Media Quality – When your media quality is not good, lowering 
down the duplication speed is necessary to make good copies.
• Poor...

www.aleratec.com38
Stand-Alone D\fplicat\Bor SA: T\ftorials
Select B\frn Speed - continued 
3. Select duplication speed type.
There are different types of recording speeds:
 ▪HDD/BD to BD: Copying to Blu-ray Media from Pre-loaded BD Partition 
or Original BD Media.
 ▪HDD/CD to CD: Copying to CD-R/RW Media from Pre-loaded CD 
Partition or Original CD Media.
 ▪HDD/DVD to DVD: Copying to DVD±R Media from Pre loaded DVD 
Partition or Original DVD Media.
 ▪HDD/DVD-DL to DVD-DL: Copying to Double/Dual Layer...

www.aleratec.com39
Stand-Alone D\fplicat\Bor SA: T\ftorials
Select the So\frce dr\Bive
When making a copy, you will need to specify where the master is. Is it in the Source 
drive? Or is it an Image inside the Hard Drive? This tutorial will show you how to 
change the Master Reading Source to satisfy your needs.
Basically, there are 3 scenarios that require you to select the Source drive.
1. Disc-to-Disc copy (Copy from 1st Tray) – This is the case when you would 
normally make copies on the fly. You...

www.aleratec.com40
Stand-Alone D\fplicat\Bor SA: T\ftorials
Select the So\frce dr\Bive - continued 
b. Enter “Source Selection” menu.
Press ENT to enter into “Source Selection” menu.
You will see the following display:
 
Make sure it is located at “Drive 1 Port 0.0”. If not, press the UP or 
DOWN navigation button to search for it. There will be drive model
information where XXXXXX is shown above.
c. Select desired master reading device.
Press the UP or DOWN button to select the desired master reading...

www.aleratec.com41
Stand-Alone D\fplicat\Bor SA: T\ftorials
Change the SETUP Settings
Most of the internal settings and information are stored inside the “Setup” menu. To 
explore and modify these settings is simple. In the following example you will be 
modifying the “Auto Start” setting. 
Note: The default “Setup\b” i\b \bet for optimal\b performance. It i\b\b unnece\b\bary to 
change thi\b \betting \bif you are \bati\bfied \bwith your duplicato\br performance.
1. Use the UP or DOWN arrow button to...

www.aleratec.com42
Stand-Alone D\fplicat\Bor SA: T\ftorials
A\fdio CD Editing
This procedure will guide you in using the “Mix Audio Tracks” feature. This process 
allows you to combine audio tracks from various CDs into a single customized 
audio CD.
To use this feature you need a temporary storage location to hold your music before 
the duplicator can make it an audio CD. The following are temporary storage 
location choices:
• Hard Drive:
Choosing “Hard Drive” as the temporary storage location, you...

www.aleratec.com43
Stand-Alone D\fplicat\Bor SA: T\ftorials
4. Once you made your selection, you will see the following display:
OR
When you see the above display, insert an audio CD that contains your music 
track(s) in the Master Reading Tray and a blank CD-R media into one of Writer 
Trays.
Note: If either one of t\bhe above \bcreen\b i\b \b\bhown for more than\b 2 
minute\b, plea\be chec\bk your Ma\bter Di\bc o\br Blank Di\bc\b for qu\bality.
Please allow 5-10 seconds for the duplicator to detect...

www.aleratec.com44
Stand-Alone D\fplicat\Bor SA: T\ftorials
A\fdio CD Editing - continued 
6. Press ENT button to submit your selection. You will see the following display:
Warning: If the capacity o\bf total audio track\b\b you have \belected\b i\b more 
than your blank CD-\bR di\bc’\b capacity, you will \bee the \bfollowing two 
\bcreen\b fla\bhing:
If you see the above messages, press ENT button to continue.
Once the Copying process is complete, you will see the following display:
7. You now have the...