Aleratec 15 HDD Copy Cruiser HighSpeed WL User Guide

www.aleratec.com15
Overview
Other Label Printi\Bng Related Options
There are other label printing related operations available as described below:
Menu 3: Copy+Print
This function allows you to perform the disc duplication then the disc labeling 
operation as part of one process.  Just flip the disc from the data side to the label   
side after each duplication pass.
To use this function, the data file required for duplication and the label file required 
for labeling will need to be preloaded onto the...

www.aleratec.com16
Overview
Control F\fnctions
For detailed descriptions of each control function and feature see the Menu Overview 
section beginning on page 59 of this User Guide. 
Control F\fnctions
1. Copy2. Print3. Copy + Print4. Test5. Compare6. Test + Copy7. Copy + Compare8. Select Burn Speed9. Select Source10. Erase11. Hard Drive Setup1. Select Partition2. Load Partition3. Rename Partition4. Delete Partition5. Partition Info6. Select Loading Drive7. Format Hard Drive12. Print Setup1. Load Label...

www.aleratec.com17
Stand-Alone D\fplicat\Bor SA: T\ftorials
Making Disc-to-Disc\B Copies
This process copies a Master Disc to several blank discs simultaneously. Due to 
the nature of simultaneous disc duplication, a good quality Master Disc and lower 
recording speeds maybe necessary to ensure high success and quality duplications 
rates.
1. Turn on the duplicator. After the duplicator has booted up, you will see the 
following display:
2. Make sure the Source Drive is set to the BD/DVD/CD source...

www.aleratec.com18
Stand-Alone D\fplicat\Bor SA: T\ftorials
4. Start the Copy Process.
a. Insert your Master Disc and blank discs into their corresponding tray(s) and 
press the ENT button. You will see the following display:
b. “Duplication Mode” offers three choices:
 ▪Load and Copy
 ▪On the Fly
 ▪Prompt
Press UP or DOWN arrow button to display your desired mode. Press the 
ENT button to confirm.
c. “No Counter” can be used when you prefer to copy continuously with no 
interruption. (It will still...

www.aleratec.com19
Stand-Alone D\fplicat\Bor SA: T\ftorials
Making Disc-to-Disc\B Copies - continued 
Example:
To enter a value of 21 copies, do the following
Make sure the cursor is located at the first position:
i. Press DOWN button consecutively until “0” is displayed.
ii. Press ENT button once to move the cursor to the next position.
iii. Press DOWN button consecutively until “0” is displayed.
iv. Press ENT button once to move the cursor to the next position.
v. Press DOWN button consecutively until...

www.aleratec.com20
Stand-Alone D\fplicat\Bor SA: T\ftorials
Note: If either one of t\bhe PREVIOUS 2 \bcreen\b\b are di\bplayed for \b
more than 2 minute\b\b, plea\be check your\b Ma\bter Di\bc or blank\b di\bc\b 
for quality.
d. Allow 5-10 seconds for the duplicator to detect both your Master Disc and 
blank discs. After your Master Disc and blank discs have been recognized, 
you will see the following display:
Note: “X” indicate\b the n\bumber of di\bc\b recog\bnized by the Writer 
Tray. For thi\b...

www.aleratec.com21
Stand-Alone D\fplicat\Bor SA: T\ftorials
Making Disc-to-Disc\B Copies - continued
e. 2 or 3 seconds after copying begins the following “Copy Progress” screen 
will appear:
Note: It i\b normal to \bee\b the progre\b\b indica\btor \btay at 0-10% a\bnd at 
100% for approximat\bely 30 \becond\b durin\bg CD duplication. Additionally 
it i\b normal to \bee \bthe progre\b\b indicat\bor \btay at 0-10% an\bd at 100% 
for up to 1 minute \bduring DVD duplication\b. There i\b a delay ca\bu\bed by...

www.aleratec.com22
Stand-Alone D\fplicat\Bor SA: T\ftorials
To continue making additional copies, remove the successfully completed copies 
from the ejected trays and replace with blank discs. To terminate your project and 
return to the main menu, press ESC. 
If you’ve specified a counter value you will see the following display when your 
project is completed:
If you see above message, you can press ENT to go back to main menu.
Note: If you enabled the\b counter and the n\bumber of blank di\bc\b \byou...

www.aleratec.com23
Stand-Alone D\fplicat\Bor SA: T\ftorials
Load So\frce Files ont\Bo the Hard Drive - continued 
You can create a new partition by either loading it directly from a Master Disc 
or by copying it directly onto the Hard Drive through the tower publisher’s USB 
connection.  Here we will discuss loading source data directly onto the Hard Drive.  
The next section will explain how to load a partition from a Master Disc.
 
The tower publisher will recognize three different formats of source...

www.aleratec.com24
Stand-Alone D\fplicat\Bor SA: T\ftorials
Load Master Disc ont\Bo the Hard Drive
The following steps will show you how to load your Master Disc into the installed 
Hard Drive as a partition and copy the stored partition onto blank discs. This process 
is recommended for mass volume production.
To load your Master Disc onto a hard drive partition, please do the following:
1. Make sure the Source is set to the Hard Drive.
It is very important to make sure the Source is set for the Hard...