Home > Alarm Lock > Alarm Lock > Alarm Lock PL3000 Programming Instructions User Manual

Alarm Lock PL3000 Programming Instructions User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Alarm Lock PL3000 Programming Instructions User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 84 Alarm Lock manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							21 
    Function Card #6 
    IMPORTANT NOTE:   
    Function Cards 3 through 7 are not recognized by DL-Windows.  Therefore, DL-Windows will not send the data for 
    Function Cards 3-7 to the AL-DTM, nor will the AL-DTM be able to send this Function Card data to the PL3000 
    lock.  Accordingly, Function Cards are designed to be used for limited-use installations where DL-Windows will not 
    be used.  When User Numbers are printed in the Audit log, Function Cards 3-7 will appear as User Numbers 
    2003-2007. 
    Initiates AL-IR1 Printing With Time, Date, Version Number and Audit Trail Log 
    Function Card #6 is used to initiate the printing of the Audit Log by the AL-IR1 Wireless Printer.  The time, 
    date and version number will also be printed.  The AL-IR1 is optically linked to the PL3000 lock via infrared light, 
    and therefore must be held approximately 1 to 4 above the infrared LED (as shown in image below).  Be sure 
    fresh batteries are installed in the AL-IR1 Wireless Printer before proceeding.  Note:  Time and date must be 
    set using DL-Windows or the AL-DTM. 
     
    Print the Audit Log as follows: 
    1.   Turn on the printer. 
    2.   Place AL-IR1 approximately 1 to 4 above the infrared LED (as shown in image). 
    3.   Present Function Card #6 to the lock.  The lock will beep twice (and flash a green LED).   
    4.   After a 2-second delay, the PL3000 lock will send the infrared signals to the printer.   
    5.   If more than 20 log entries exist in the lock, after the 20th entry a line will print:  More?.  The lock will 
    beep twice every second (with a green LED) for 15 seconds.  (If there are less than 20 log entries, the 
    lock will end the printing sequence and return to normal operation). 
    •To continue printing, re-present a card to print the next 20 Logs (during which the beeping and flashing 
    will stop).  Step 5 will be repeated if more logs exist. 
    •If a card is not presented, the lock will end the printing sequence within 15 seconds (signified by a red 
    LED and two beeps), after which the lock will return to normal operation. 
     
    Note:  Turn off the printer when not in use. 
    Function Card # 6 
    AC 
    Adapter 
    (Optional) 
    Paper Compartment 
    Optical 
    Receiver 
    Thermal 
    Print Head 
    On/Off 
    Print  
    Contrast 
    Paper 
    Advance 
    Power ON 
    Indicator 
    Light 
    Infrared 
    LED 
    Infrared 
    Receiver 
    AL-IR1 to PL3000 (side and front views)  
    						
    							22 
    Function Card #7 
    IMPORTANT NOTE:   
    Function Cards 3 through 7 are not recognized by DL-Windows.  Therefore, DL-Windows will not send the data for 
    Function Cards 3-7 to the AL-DTM, nor will the AL-DTM be able to send this Function Card data to the PL3000 
    lock.  Accordingly, Function Cards are designed to be used for limited-use installations where DL-Windows will not 
    be used.  When User Numbers are printed in the Audit log, Function Cards 3-7 will appear as User Numbers 
    2003-2007. 
     
     
    Toggles Total User Lockout Mode 
    Total User Lockout mode is useful for when absolute security is required.  When Function Card #7 is pre-
    sented, Total User Lockout mode is enabled.  Total User Lockout disables all other enrolled cards and 
    freezes the system state.  For example, if the lock were in Passage Mode and Function Card #7 were pre-
    sented, the lock would henceforth remain in Passage Mode (unlocked), with none of the other cards able to 
    remove the lock from this state.  Note:  Schedules created using DL-Windows will still place the lock into or 
    out of Passage Mode even when Function Card #7 is used. 
     
    Enter Total User Lockout mode as follows: 
    •Present Function Card #7 to the lock.  The PL3000 unlocks and the green LED blinks twice, accompa-
    nied by two beeps.  The PL3000 locks and flashes a red LED.  The PL3000 is now in Total User Lock-
    out mode.  If a valid card is presented, the lock will beep 6 times and flash a combination red and 
    green LED with 4 additional red LED flashes.  If an invalid card is presented, the normal sequence of 
    beeps and flashes will occur (7 red LED flashes and 7 beeps).   
     
    Exit Total User Lockout mode as follows: 
    •Present Function Card #7 to the lock.  The PL3000 unlocks and the green LED blinks twice, accompa-
    nied by a beep.  The PL3000 relocks and flashes a red LED.  The lock resumes its normal operation. 
    Function Card # 7  
    						
    							23 
    Function Card #8 
    IMPORTANT NOTE:   
    Function Cards 3 through 7 are not recognized by DL-Windows.  Therefore, DL-Windows will not send the data for 
    Function Cards 3-7 to the AL-DTM, nor will the AL-DTM be able to send this Function Card data to the PL3000 
    lock.  Accordingly, Function Cards are designed to be used for limited-use installations where DL-Windows will not 
    be used.  When User Numbers are printed in the Audit log, Function Cards 3-7 will appear as User Numbers 
    2003-2007. 
    Enables and Resets Function Card #9 (User 297) 
    Function Card #8 (assigned to User 297) possesses the unique ability to enable Function Card #9 (assigned to 
    User 300).  When Function Card #8 is presented to the lock, User 300 is enabled, allowing Function Card #9 to 
    unlock the PL3000 (for one time).  Once used, Function Card #9 (User 300) becomes disabled. 
     
    For example, you wish to allow one-time access to a temporary worker.  Simply present Function Card #8 to the 
    lock and give Function Card #9 to your temporary worker.  Later, when the temporary worker presents Function 
    Card #9 to the lock, the PL3000 unlocks and allows access (for one time only).  If the temporary worker re-
    presents Function Card #9, access will be denied.  Later, if you wish to grant the temporary worker re-access, sim-
    ply re-present Function Card #8 to the lock (no need to have possession of Function Card #9) and Function Card 
    #9 will be re-enabled (again for one time only).   
     
    (NOTE:  Function Card #9 is enabled from the factory after the PL3000 is started for the first time.  W hen Func-
    tion Card #9 is first presented after the PL3000 is first put into service, the PL3000 will unlock even without 
    Function Card #8 being presented first.  However, once presented, Function Card #9 will then become dis-
    abled). 
     
    Activate Function Card #9 as follows: 
    •Present Function Card #8 to the lock.  The PL3000 unlocks and the green LED blinks twice, accompa-
    nied by two beeps.  After the door unlock delay time, the PL3000 re-locks and flashes a red LED.  
    Function Card #9 is now activated and is ready to be used for as long as the lock is in continuous op-
    eration (months and years can pass--Function Card #9 will still be active and ready to use).   
    •When Function Card #9 is presented, the door will unlock in the standard manner (two green LED 
    flashes and two beeps will sound).   
    •If Function Card #9 is re-presented without Function Card #8 being presented first, the lock will sound a 
    series of 6 warning beeps and will flash a combination red and green LED with 4 additional red LED 
    warning flashes.   
    Function Card # 8  
    						
    							24 
    Function Card #9 
    IMPORTANT NOTE:   
    Function Cards 3 through 7 are not recognized by DL-Windows.  Therefore, DL-Windows will not send the data for 
    Function Cards 3-7 to the AL-DTM, nor will the AL-DTM be able to send this Function Card data to the PL3000 
    lock.  Accordingly, Function Cards are designed to be used for limited-use installations where DL-Windows will not 
    be used.  When User Numbers are printed in the Audit log, Function Cards 3-7 will appear as User Numbers 
    2003-2007. 
    The Service Card, Allowing Access One-Time-Only (User 300) 
    Function Card #9 is also known as a Service Card because it is the card usually given to Service personnel 
    (temporary workers who wish to be granted access only once).   
     
    Function Card #9 is activated by the presentation of Function Card #8.  See Function Card #8 on previous 
    page. 
     
    Function Card #8 (assigned to User 297) possesses the unique ability to enable Function Card #9 (assigned to 
    User 300).  When Function Card #8 is presented to the lock, User 300 is enabled, allowing Function Card #9 to 
    unlock the PL3000 (for one time).  Once used, Function Card #9 (User 300) becomes disabled. 
     
    For example, you wish to allow one-time access to a temporary worker.  Simply present Function Card #8 to the 
    lock and give Function Card #9 to your temporary worker.  Later, when the temporary worker presents Function 
    Card #9 to the lock, the PL3000 unlocks and allows access (for one time only).  If the temporary worker re-
    presents Function Card #9, access will be denied.  Later, if you wish to grant the temporary worker re-access, sim-
    ply re-present Function Card #8 to the lock (no need to have possession of Function Card #9) and Function Card 
    #9 will be re-enabled (again for one time only).   
     
    (NOTE:  Function Card #9 is enabled from the factory after the PL3000 is started for the first time.  W hen Func-
    tion Card #9 is first presented after the PL3000 is first put into service, the PL3000 will unlock even without 
    Function Card #8 being presented first.  However, once presented, Function Card #9 will then become dis-
    abled). 
     
    Activate Function Card #9 as follows: 
    •Present Function Card #8 to the lock.  The PL3000 unlocks and the green LED blinks twice, accompa-
    nied by two beeps.  After the door unlock delay time, the PL3000 re-locks and flashes a red LED.  
    Function Card #9 is now activated and is ready to be used for as long as the lock is in continuous op-
    eration (months and years can pass--Function Card #9 will still be active and ready to use).   
    •When Function Card #9 is presented, the door will unlock in the standard manner (two green LED 
    flashes and two beeps will sound).   
    •If Function Card #9 is re-presented without Function Card #8 being presented first, the lock will sound a 
    series of 6 warning beeps and will flash a combination red and green LED with 4 additional red LED 
    warning flashes.   
    Function Card # 9  
    						
    							25 
    User Card Record Sheet 
    NAME OF DOOR:                                                      DEPARTMENT: 
     
    EMBOSSED NUMBER ON CARD USER NAME (LAST, FIRST) DATE ACTIVATED COMMENTS 
        
        
        
        
        
        
        
        
        
        
        
        
        
        
        
        
        
        
        
        
        
        
        
        
        
        
        
        
        
        
        
        
     
     Page # ______  
    						
    							26 
    ACCESS = Entry into a restricted area. 
    AUDIT TR AIL = A date/time stamped log of previous lock events. 
    BURGLARY CONTROL PANEL = Provides local alarm and remote 
    communication to request security for burglary/break-in.   
    CLOCK 
    •REAL TIME CLOCK = An accurate built-in clock that allows 
    date/time stamping of events.  The clock can be slowed or 
    speeded up to fine tune long term accuracy to within three 
    minutes per year.  Programmed only through DL-Windows.   
    •CLOCK SETTINGS = Printout includes date, time, weekday, 
    and clock speed. 
    COM PORT = A computer serial communications port used to com-
    municate with the Lock and/or Data Transfer Module. 
    DATA TRANSFER MODULE = A device that permits transfer of 
    program/data between a computer and the lock.  AL-DTM 
    Transfer Module. 
    DATE = Month, Day and Year entered as MMDDYY.  Programmed 
    only through DL-Windows.   
    DAY OF WEEK = Sunday through Saturday (where 1 = Sunday and 
    7 = Saturday).  Programmed only through DL-Windows.   
    DEFAULT = Default settings are the original settings that were set 
    at the factory; in other words, it is the locks original factory con-
    dition when the lock was first taken out of its box.  The default 
    settings are permanently encoded within the locks fixed mem-
    ory, and when the lock is first started, or when power is removed 
    and re-applied (see Wiring and Power-Up, page 11), the original 
    factory default settings are re-loaded and take effect. 
    DISABLE = Turn off. 
    DOOR NUMBER = Identification of each door with a specific num-
    ber (1-96). (Used with AL-DTM Transfer Module) 
    DOWNLOAD = Send data to lock or AL-DTM. 
    ENABLE = Turn on. 
    EVENTS = Recorded lock activity. 
    GROUP 
    •USER GROUP = Defining a User to specific Groups, allows 
    User entry when the Group is allowed entry.  Programmed 
    only through DL-Windows.   
    •GROUP 1 DISARMS BURGLAR CONTROL = A Group 1 
    USER CARD entry can disarm an alarm panel during a prede-
    fined schedule.  Should the Group 1 enter the lock outside of 
    the scheduled time, the alarm will not disarm. The alarm panel 
    must be armed through other means.  The Burglary Alarm 
    Panel must be programmed to disarm from an Armed State 
    Only and the zone input must be programmed for input dis-
    arming.  Programmed only through DL-Windows.   
    •GROUP 1 ENABLES GROUP 4 USERS = A Group 1 USER CARD entry during a predefined schedule will allow access to 
    Group 4 Users.  Programmed only through DL-Windows.   
    •GROUP 1 PUTS UNIT IN PASSAGE = A Group 1 USER 
    CARD entry during a pre-defined schedule will unlock unit.  
    Programmed only through DL-Windows.   
    •ONE TIME ONLY FOR GROUP 3 USERS = If selected in DL-
    Windows, allows Group 3 Users to unlock the door one time 
    only, then their proximity card becomes disabled.  See OI237. 
    LOG = See... AUDIT TRAIL. 
    PASSAGE = Allow anyone to pass through the door without USER 
    CARDS (door unlocked). 
    PRINTER = A printout device such as an infrared printer or com-
    puter printer. 
    PROGRAMMABLE RELAY FUNCTIONS = The relay can be pro-
    grammed (via DL-Windows only) for one or more functions.  See 
    page 27 for more information. 
    RELAY = Switched output allowing remote control of other devices.   
    REMOTE INPUT = Entry into a restricted area, by pressing a button 
    connected to the REMOTE INPUT WIRES (white and white) by 
    someone on the other side of the door. 
    SCHEDULE = A programmed operation (enable/disable, lock/
    unlock, etc.) on a specific day (Sunday through Saturday) and 
    time.  Programmed only through DL-Windows.   
    SCHEDULES, QUICK = Any one of four most common types of 
    schedules can be programmed.  Programmed only through DL-
    Windows.   
    TIME = Hours and Minutes in the HHMM format.  Programmed only 
    through DL-Windows.   
    TIME/DATE STAMP = A recorded date and time that an event oc-
    curred. 
    TIMEOUT = Immediate operation for a specified number of hours. 
    UPLOAD = Receive data from the lock or AL-DTM. 
    USER = A person who has been provided with a USER CARD for 
    access through the door. 
    USER LOCKOUT, TOTAL = All Users to be locked out (denied ac-
    cess).  User Cards will not unlock the device.  
     
    Glossary  
    						
    							27  •Relay Functions 
    Lost Function Cards 
    The implications of lost Function Cards can be inconvenient or serious, depending on how you decided to implement your 
    PL3000 lock, which Function Cards were lost, and if you saved the Lock Program in DL-Windows.  The following assumes that 
    ALL Function Cards have been lost, and you wish to preserve the distributed User Cards that are in use, and replace the lost 
    Function Cards with a new set. 
    If you made use of DL-Windows, and the Lock Program containing all the active User Cards is safely stored within DL-
    Windows, then the result will be simply inconvenience.  You will need to Erase all lock programming and enroll a new set of Func-
    tion Cards, enroll the new Function Cards (1,2,8 & 9 only) into the existing DL-Windows program, then send the DL-Windows 
    Lock Program to the lock.  Proceed as follows: 
    1.Obtain entry to the door secured by the PL3000. 
    2.At the back of the lock, remove the screw at the bottom of the lock housing and remove the cover.  Follow and complete 
    the ERASE ALL PROGRAMMING procedure on page 11.  When finished, a new set of 9 Function Cards will be enrolled 
    into the lock. 
    3.Enroll the new set of Function Cards into the existing DL-Windows program via the AL-PRE.  Since DL-Windows 
    does not recognize Function Cards 3-7, only enroll Function Cards 1, 2, 8 and 9 into DL-Windows.  See OI237 for this DL-
    Windows procedure.   
    4.Transfer the Lock Program from DL-Windows to the lock.  Use the new Function Card #1 to initiate the transfer.  See 
    page 15 Send Information to Lock for the procedure.   
    If you did NOT make use of DL-Windows and enrolled the Function Cards only, and all Function Cards are lost, then your only 
    choice will be to erase all programming (and re-program the lock as if you had removed the lock from its factory box).  This will 
    require that all User Cards be re-entered or replaced (the cards must be at hand to do so), and all other programming be re-
    peated. 
    If Function Cards 3-7 are misplaced, perform the above steps with new proximity cards (to replaces the missing cards).  Enroll 
    Function Cards 1, 2, 8 and 9 into DL-Windows before communicating.   
    DL-Windows Programmable Features 
    •Other System Functions  
    25. Disable Sounder  
    26. 5 sec. Delayed Entry *  
    27. 15 sec. Delayed Entry *  
    28. 45 sec. Delayed Entry * 
    •Remote Input Functions 
    29. Toggle Passage Mode.  Remote Input toggles Passage Mode. 
    30. Forced Unlock Follows Remote Input.**  When Remote Input is 
    activated, relay will energize (regardless of its current state).  
    32. Remote Input Disables Unit.**  Regardless of the current state, 
    that state will remain unchanged (and card reader will be disabled) 
    for the duration of Remote Input switch closure. 
    *  Features 26, 27 & 28 will delay User Codes 12 and higher only (except 297, 298 and 299). 
    ** Features 30, 31 & 32 should be used with external DC power unless feature is used for a short duration and infrequently (sustained closure of remote input or relay 
    will drain batteries).  Sustained closure of remote input will inhibit scheduled events and may affect proper audit trail operation. 
    •PC Communication Function 
    33. Remote Input places PL3000 into PC Communication Mode 
    1.    Remote Input switch closed (with Remote Input enabled).  The 
    Remote Input is enabled by factory default but can be disabled 
    and re-enabled by DL-Windows.  If this feature is programmed, the 
    Relay will energize when the Remote Input switch is closed.
     2.    Remote Input switch closed (with Remote Input disabled).  If 
    the Remote Input is disabled via DL-Windows, the relay will NOT 
    energize when the Remote Input switch is closed.
     3.    Failed Attempted Entry.  Relay energizes for 2 seconds when a 
    presented proximity card / keyfob fails. 4.    Disabled User or Group.  Relay energizes for 2 seconds when a 
    disabled User or disabled Group member presents a proximity 
    card / keyfob.
     5.    Follow Access Granted.  Relay energizes for 2 seconds when a 
    valid proximity card / keyfob is presented (and the lock unlocks).   
           Compare with Event 31.
     6.    Group 1 User Code.  Relay energizes for 2 seconds when a 
    Scheduled Group 1 Activated proximity card / keyfob is presented.  For information regarding Scheduled Group 1 Activated relay func-
    tions, see the DL-Windows Users Guide, OI237.  
     7.    Scheduled Lock Event.  Relay energizes for 2 seconds when 
    lock is locked by a pre-programmed Schedule.   8.    Scheduled Unlock Event.  Relay energizes for 2 seconds when 
    lock is unlocked by a pre-programmed Schedule. 9.    Lock Out.  Relay energizes for 2 seconds when a Lock Out oc-
    curs (i.e. when a number of failed entry attempts is exceeded). 11. An y Attempted Entry.  Relay energizes for 2 seconds when any 
    proximity card / keyfob (enabled or disabled) is presented. 31. Follow Access Granted--No Time Limit.**  When a valid prox-
    imity card / keyfob is presented (and the lock unlocks), the Relay 
    energizes for the same amount of time as the programmed Pass 
    Time.  (The Pass Time is the length of time the lock remains 
    unlocked after a valid proximity card / keyfob is presented).   
           Use this feature for remote monitoring or other activation.  
     
    You can use DL-Windows to program the PL3000 to perform certain functions (listed below) when various events occur.    For example, program Relay Function #3 to energize the relay for 2 seconds when an attempted entry fails (as when an un-
    programmed proximity card is presented to the lock).  For a description of all features, see the DL-Windows Users Guide, 
    OI237; the most common are listed below:  
    						
    							28 
    ALARM LOCK LIMITED WARRANTY 
     
    ALARM LOCK SYSTEMS, INC. (ALARM LOCK) warrants its products to be free from manufacturing defects in mate-
    rials and workmanship for 24 months following the date of manufacture. ALARM LOCK will, within said period, at its 
    option, repair or replace any product failing to operate correctly without charge to the original purchaser or user. 
    This warranty shall not apply to any equipment, or any part thereof, which has been repaired by others, improperly 
    installed, improperly used, abused, altered, damaged, subjected to acts of God, or on which any serial numbers have 
    been altered, defaced or removed. Seller will not be responsible for any dismantling or reinstallation charges. 
    THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, WHICH EXTEND BEYOND THE DESCRIPTION ON 
    THE FACE HEREOF. THERE IS NO EXPRESS OR IMPLIED WARRANTY OF MERCHANTABILITY OR A WAR-
    RANTY OF FITNESS FOR A PARTICULAR PURPOSE. ADDITIONALLY, THIS WARRANTY IS IN LIEU OF ALL 
    OTHER OBLIGATIONS OR LIABILITIES ON THE PART OF ALARM LOCK. 
    Any action for breach of warranty, including but not limited to any implied warranty of merchantability, must be 
    brought within the six months following the end of the warranty period. IN NO CASE SHALL ALARM LOCK BE LI-
    ABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY 
    OTHER WARRANTY, EXPRESS OR IMPLIED, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLERS 
    OWN NEGLIGENCE OR FAULT. 
    In case of defect, contact the security professional who installed and maintains your security system. In order to exer-
    cise the warranty, the product must be returned by the security professional, shipping costs prepaid and insured to 
    ALARM LOCK. After repair or replacement, ALARM LOCK assumes the cost of returning products under warranty. 
    ALARM LOCK shall have no obligation under this warranty, or otherwise, if the product has been repaired by others, 
    improperly installed, improperly used, abused, altered, damaged, subjected to accident, nuisance, flood, fire or acts 
    of God, or on which any serial numbers have been altered, defaced or removed. ALARM LOCK will not be responsi-
    ble for any dismantling, reassembly or reinstallation charges. 
    This warranty contains the entire warranty. It is the sole warranty and any prior agreements or representations, 
    whether oral or written, are either merged herein or are expressly canceled. ALARM LOCK neither assumes, nor au-
    thorizes any other person purporting to act on its behalf to modify, to change, or to assume for it, any other warranty 
    or liability concerning its products. 
    In no event shall ALARM LOCK be liable for an amount in excess of ALARM LOCKs original selling price of the prod-
    uct, for any loss or damage, whether direct, indirect, incidental, consequential, or otherwise arising out of any failure 
    of the product. Sellers warranty, as hereinabove set forth, shall not be enlarged, diminished or affected by and no 
    obligation or liability shall arise or grow out of Sellers rendering of technical advice or service in connection with 
    Buyers order of the goods furnished hereunder. 
    ALARM LOCK RECOMMENDS THAT THE ENTIRE SYSTEM BE COMPLETELY TESTED WEEKLY. 
    Warning: Despite frequent testing, and due to, but not limited to, any or all of the following; criminal tampering, electri-
    cal or communications disruption, it is possible for the system to fail to perform as expected. ALARM LOCK does not 
    represent that the product/system may not be compromised or circumvented; or that the product or system will pre-
    vent any personal injury or property loss by burglary, robbery, fire or otherwise; nor that the product or system will in 
    all cases provide adequate warning or protection. A properly installed and maintained alarm may only reduce risk of 
    burglary, robbery, fire or otherwise but it is not insurance or a guarantee that these events will not occur. CONSE-
    QUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE, OR 
    OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING. Therefore, the installer should in 
    turn advise the consumer to take any and all precautions for his or her safety including, but not limited to, fleeing the 
    premises and allege police or fire department, in order to mitigate the possibilities of harm and/or damage. 
    ALARM LOCK is not an insurer of either the property or safety of the users family or employees, and limits its liability 
    for any loss or damage including incidental or consequential damages to ALARM LOCKs original selling price of the 
    product regardless of the cause of such loss or damage. 
    Some states do not allow limitations on how long an implied warranty lasts or do not allow the exclusion or limitation 
    of incidental or consequential damages, or differentiate in their treatment of limitations of liability for ordinary or gross 
    negligence, so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights 
    and you may also have other rights which vary from state to state.  
    						
    All Alarm Lock manuals Comments (0)

    Related Manuals for Alarm Lock PL3000 Programming Instructions User Manual