Alarm Lock DL3000 Programming Instructions User Manual

11 
ACTIVITY LED SOUNDER COMMENTS 
Keypress 1 RED Flash 1 Beep Normal Operation 
Access Granted or Remote Input 2 GREEN Flashes 2 Beeps For Remote Input, wire a normally 
open contact to these two white 
wires.  Momentarily close to 
unlock.  See page 10 for more in-
formation. 
Valid Code  1 Momentary GREEN 
Flash   
Invalid Code 6 RED Flashes 6 Beeps Re-enter User Code 
Successful Program Entry 1+2 GREEN Flashes 1+2 Beeps When in Program Mode 
Unsuccessful Program Entry 7 RED Flashes 7 Beeps When in...

12 
Product Communication Examples 
NOTE:  
The AL-PCI cable is designed to be used on a 9 pin serial COM port.  If your computer has a 25 pin COM port, a 25 pin to 9 pin adapter must be used.   
Warning:  Polarity MUST be observed when connecting cables to the lock.  The tab (-) must plug into the negative (black) hole. 
Scenario 3   Use the AL-IR1 Infrared printer to print your lock’s audit trail (event log), User Code list, clock settings and software 
version.  No cable required. 
Scenario 1   Create...

13 
Programming Functions--Overview 
Function 1 New Master Code  14 
Function 2 Add/Delete/Change User Codes 
2-300  14 
Function 3 Disabling Users (By User Num-
ber) 14 
Function 4 Enabling Users (By User Number) 14 
Function 5 User Enable with Timeout  15 
Function 6 Enable Total User Lockout Mode 15 
Function 7 Disable Total User Lockout Mode 15 
Function 8 Change User Programming Level 
Ability 15 
Function 9 Enable User 300 (Service Code) 15 
Function 10 Erase All Users Except the Mas-
ter Code...

14 
Enabling/Disabling Users (By User Number) 
USERS 
Programming Functions 
1. New Master Code (User Number 1) ; 1      ; [ _ _ _ _ _ _ ]           ; [ _ _ _ _ _ _ ] : 
   (New Master Code)                  (Confirm New Master Code) 
•Master Code must be 6 digits-only. 
•Factory Default = 123456 
•NOTE:  Following a power up, it is highly recommended that Function 1 (New Master 
Code), be accessed and the factory default Master Code changed before programming 
any other functions.
 
•See Lock Design...

15 
USERS (Continued) 
8. Change User Programming Level Ability ; 8       ; [ _ _ _ ]           ; [ _ _ _ _ ] :  
                           (User Number)                (Programming Levels) 
Service Code is a One-Time-Only code.  Once it is used, it is disabled until enabled again. 
; 9 : 9. Enable User 300 (Service Code) 
User Number must be between 2 and 255.  The ability to program one or more Programming 
Levels may be selected. 
 Example 1: Allow Basic User 67 to program levels 1, 2 and 4.  Enter:...

16 
CLEAR FUNCTIONS 
GROUPS 
24. Reserved 
Programming Functions (contd) 
Group Enable/Disable 
Enter the functions below to Enable/Disable Groups.  Functions 14 - 23 will each override 
existing scheduled events.  Therefore, Functions 14 - 23 are temporary, take effect im-
mediately, and are always overridden by future scheduled events that already exist within 
the lock programming.  2 
; 1 4 : 
; 1 5 : 
16. Disable Group 3 ; 1 6 : 
17. Disable Group 4 ; 1 7 : 
18. Disable All Groups ; 1 8 : 
19....

17 
GROUPS 
36 - 37. Reserved 
Clear All Timeout Functions by entering Function 13.   NOTE:  
Programming Functions (contd) 
Group Enable/Disable with Timeout (Enter Timeout, XXX Hours) (Functions 25-34 are enabled through the keypad only) 
•Hours must be between 1-999.  Enter the functions below to Enable/Disable Groups for the amount of time entered in hours. 
         NOTE:   Only 4 Timeout Functions are allowed at any one time.  An error beep will sound when attempting to program more 
than 4 Timeout...

18 
CLOCK SETTINGS 
Programming Functions (contd) 
; 3 8      ; [ _ _ _ _ _ _ ] :  
  
(Date) 
38. Set Date 
•Use Month Day Year format - MMDDYY - Single digit months and days are entered with a preceding zero. 
•Enter ONLY the last two digits of the year. 
 
For Example: March 8, 2005;  
 Enter: ; 3 8      ; 0 3   0 8    0 5 : 
 3 
39. Set Time ; 3 9      ; [ _ _ _ _ ] :  
  
(Time) 
•Time must be 4 digits 
•Use 24 Hour Format (add 12 hours to program PM time) 
 For Example:  To set time to 8:25 PM;...

19 
CLOCK ADJUST 
PASSAGE MODE 
Programming Functions (contd) 
; 4 5 : 45. Enable Passage Mode (This Function enabled through keypad only) 
; 4 6 : 46. Disable Passage Mode (This Function enabled through keypad only) 
47. Timed Passage Mode (This Function enabled through keypad only) 
; 4 7      ; [ _ _ _ ] :  
(XXX Hours) 
•Function 45 allows passage through the door without the need for a User Code.  Re-Lock using Function 46.   
•Programmed Schedules will override the state of the lock when Functions...

20 
; 5 1 : 51. Set Pass Time 3 to 5 Sec. 
; 5 2 : 
; 5 3 : 
Pass Time 
52. Set Pass Time to 10 Sec.
53. Set Pass Time to 15 Sec.
54. Reserved 
PASS TIME 
Programming Functions (contd) 
49. Disable Permanent Passage Mode (This Function enabled through keypad only) 
50. Return Lock to Normal Passage 
Mode Schedule 
(This Function enabled through keypad only) (Locks will lock or unlock depending on the current schedule).  Use Function 50 to undo 
Functions 48 and/or 49, and therefore return the lock to all...