Air Live Router WT-2000ARM User Manual

 
AirLive WT-2000ARM User’s Manual 
 26
z Encapsulation 
The router can be connected to your service provider in any of the following ways. 
 
Parameter Description 
Dynamic IP Address   Obtain an IP address automatically from your service provider.  
  
Static IP Address   Uses a static IP address. Your service provider gives a static IP 
address to access Internet services. 
  
PPPoE/PPPoA  PPPoE (PPP over Ethernet) and PPPoA (PPP over ATM) are 
common connection methods used for xDSL.  
  
Bridge Mode...

 
AirLive WT-2000ARM User’s Manual 
 27
segment size (MSS) for transient packets that traverse a router, 
specifically TCP segments in the SYN bit set, when PPPoE is being 
used in the network. Please specify the MSS range from 100 to 1452 
bytes or 0 byte as the default value. 
 
Parameter Description 
Get IP Address  Choose Static or Dynamic IP Address. If Static IP is selected, please 
set the IP Address, Subnet Mask and Gateway obtained from your 
ISP. 
  
Static IP Address  Enter the IP Address...

 
AirLive WT-2000ARM User’s Manual 
 28
Multicast  Specify the method of transmitting data simultaneously to many 
receivers.  Please select “IGMP v1” or “IGMP v2” as the multicast 
protocol or select “Disabled” to disable the function. 
 
 
 LAN 
 
 
 
z Router Local IP 
 
Parameter Description 
IP Address  Enter the IP Address of the ADSL router for the local user to access 
the router’s web page. By default, the IP Address is 192.168.2.1. 
 
Parameter Description 
IP Subnet Mask  Enter the Subnet Mask...

 
AirLive WT-2000ARM User’s Manual 
 29
Only” or “OUT Only”. 
  
Multicast  Specify the method of transmitting data simultaneously to many 
receivers.  Please select “IGMP v1” or “IGMP v2” as the multicast 
protocol or select “Disabled” to disable the function. 
 
 
z DHCP 
 
Parameter Description 
DHCP  You can enable or disable the DHCP server. By enabling the DHCP 
server the router will automatically give your LAN clients an IP 
address. If the DHCP is not enabled then you’ll have to manually set...

 
AirLive WT-2000ARM User’s Manual 
 30
preferred DNS Server IP Address. 
  
Secondary DNS Server  This is optional. You can enter another DNS Server’s IP Address as 
a backup. The secondary DNS will be used should the Primary DNS 
fail. 
 
 Wireless 
 
 
 
z Wireless LAN 
 
Parameter Description 
Access Point  Activated or deactivated the wireless function of the router. When it 
is activated, the router will be an access point for other wireless 
clients to connect wirelessly.  
  
SSID  The SSID (up...

 
AirLive WT-2000ARM User’s Manual 
 31
Broadcast SSID  Select “Yes” to make the SSID to be visible so wireless clients can 
scan the router within the network. Select “No” if you want to hide 
the SSID of the router. Wireless clients have to set the same SSID of 
the router in order to access the network. 
  
Channel ID  The radio channel used by the wireless LAN. All devices in the same 
wireless LAN should use the same channel. 
  
Authentication Type  To prevent unauthorized wireless clients from...

 
AirLive WT-2000ARM User’s Manual 
 32
z Advanced Setting 
 
Parameter Description 
Beacon Interval  The interval of time that this wireless router broadcast a beacon. 
Beacon is used to synchronize the wireless network. The range for 
the beacon period is between 20 and 1000 with a typical value of 
100 (milliseconds).  
  
RTS/CTS Threshold  When the packet size is smaller than the RTS threshold, the wireless 
router will not use the RTS/CTS mechanism to send this packet. The 
range is from 1500 to...

 
AirLive WT-2000ARM User’s Manual 
 33
Address you have specified can access to the router. 
Deny Association – The wireless clients with the MAC Address you 
have specified will be denied accessing to the router. 
 
Mac Address #1-8  Please enter the MAC Address of the wireless clients for the filtering 
control. 
 
 Advanced Setup 
 Firewall 
 
 
 
Parameter Description 
Firewall  When you enable the firewall function, it will protect you from 
following attacks of WAN side: 
z SYN flooding attack 
z...

 
AirLive WT-2000ARM User’s Manual 
 34
 Routing 
 
 
 
z Routing Table List 
You can see the current routing table of the router here. If you want to add another routing rule, please 
click “ADD ROUTE”. 
 
Parameter Description 
Dest IP  Show the IP Address of the destination LAN. 
  
Mask  Show the Subnet Mask of the destination LAN. If it shows “8” that 
means the Subnet Mask is “255.0.0.0”; “16” means the Subnet Mask 
is “255.255.0.0”; “24” means the Subnet Mask is “255.255.255.0”. 
 
 
Parameter...

 
AirLive WT-2000ARM User’s Manual 
 35
port. 
  
Use  The counter for access time. 
  
Edit  Edit the route, this icon is not shown for system default route. 
  
Drop  Drop the route, this icon is not shown for system default route. 
 
z Add Route 
If you have another router with a LAN-to-LAN connection, you may need to create a static routing on 
the router that is the gateway to Internet. 
 
 
 
Parameter Description 
Destination IP Address   Enter the IP Address of the destination LAN. 
  
IP Subnet...