Air Live Router WT-2000ARM User Manual

 
AirLive WT-2000ARM User’s Manual 
 6
Chapter III: Setup Wizard 
This router provides a Setup Wizard tool for user to configure the ADSL settings. This wizard collects 
some ISP’s ADSL settings so that user can easy to configure the router’s ADSL settings by only 
selecting the ISP vendor from the wizard. 
 
If you cannot find your ISP from the wizard, please refer to the Section 5.1 to run the Quick Start 
wizard in the web management of the router. 
 
Before you start, please check the following...

 
AirLive WT-2000ARM User’s Manual 
 7
3.  This wizard will be executed and try to search for the ADSL Router. 
 
 
4.  If the router cannot be found, please enter the IP Address and the Password of the router to 
search again. Click “Next” to continue. 
  
 
 
 
 
  

 
AirLive WT-2000ARM User’s Manual 
 8
5.  Please select the country you have installed the ADSL router and click “Next”.  
 
 
6.  Please select the ISP (Internet Service Provider) of your ADSL service. 
 
 
 
 
 
 
 
  

 
AirLive WT-2000ARM User’s Manual 
 9
7.  Enter the Username and Password which your ISP has provided to you if it is needed. Click “Next”. 
 
 
8.  Click “Save” to save the settings and reboot the router.  
 
 
 
 
 
 
 
  

 
AirLive WT-2000ARM User’s Manual 
 10
9.  After saving and rebooting the router, the ISP settings are all finished. This wizard will then help to 
set your computer to obtain IP Address from the router automatically. 
Note1: Using the router to get into the Internet, the IP Address of each PC has to be set in 
the same subnet as the router. This wizard will help to set the proper IP Address to your 
computer. 
Note2: By default, the router’s DHCP Server is enabled. If it is disabled before running the...

 
AirLive WT-2000ARM User’s Manual 
 11
10.  The ISP settings are all finished. If you want to configure more settings, please click “Advanced 
Settings” or click “Finish” to close the wizard. 
 
  

 
AirLive WT-2000ARM User’s Manual 
 12
Chapter IV: IP Address Setting 
Using the router to get into the Internet, the PCs in the network must have Ethernet adapter installed 
and be connected to the router either directly or through a hub or switch. The TCP/IP protocol of each 
PC has to been installed and the IP Address of each PC has to be set in the same subnet as the 
router. 
 
The router’s default IP Address is 192.168.2.1 and the subnet mask is 255.255.255.0. PCs can be 
configured to obtain IP...

 
AirLive WT-2000ARM User’s Manual 
 13
 
 
5. Click OK to confirm the setting. Your PC will now obtain an IP address automatically from your 
router’s DHCP server. 
 
Note: Please make sure that the router’s DHCP server is the only DHCP server available on 
your LAN. 
 
Windows 2000 
 
1. Click the Start button and select Settings, then click Control Panel. The Control Panel window will 
appear. 
 
2.  Double-click Network and Dial-up Connections icon. In the Network and Dial-up Connection 
window,...

 
AirLive WT-2000ARM User’s Manual 
 14
5.  In the Internet Protocol (TCP/IP) Properties window, select Obtain an IP address automatically 
and Obtain DNS server address automatically as shown on the following screen. 
 
 
 
6. Click OK to confirm the setting. Your PC will now obtain an IP address automatically from your 
Broadband Router’s DHCP server. 
 
Note: Please make sure that the router’s DHCP server is the only DHCP server available on 
your LAN. 
 
 
 
 
 
 
 
 
 
 
 
 
  

 
AirLive WT-2000ARM User’s Manual 
 15
Windows 95/98/Me 
 
1. Click the Start button and select Settings, then click Control Panel. The Control Panel window will 
appear. 
2. Double-click Network icon. The Network window will appear. 
3.  Check your list of Network Components. If TCP/IP is not installed, click the Add button to install it 
now. If TCP/IP is installed, go to step 6. 
4.  In the Network Component Type dialog box, select Protocol and click Add button. 
5.  In the Select Network Protocol...