Air Live Router WL-1000UR User Manual

							
 81
4. Windows 2000 RADIUS server Authentication testing: 
 
4.1DUT authenticate PC1 using 
certificate. (PC2 follows the same test procedures.) 
1.  Download and install the certificate on PC1. (Fig 4) 
2.  PC1 choose the SSID of DUT as the Access Point. 
3.  Set authentication type of wireless  client and RADIUS server both to 
EAP_TLS. 
4.  Disable the wireless connection and enable again. 
5.  The DUT will send the users cert ificate to the RADIUS server, and 
then send the message of authentication result to PC1. (Fig 5) 
6.  Windows XP will prompt that the  authentication process is success or 
fail and end the authentication procedure. ( Fig 6) 
7.  Terminate the test steps when PC1 get dynamic IP and PING remote  host successfully. 
 
 
Figure 4: Certificate information on PC1 
  
						

							
 82
 
Figure 5: Authenticating   
 
 
Figure 6: Authentication success 
 
4.2DUT authenticate PC2 using PEAP-TLS. 
1.  PC2 choose the SSID of DUT as the Access Point. 
2.  Set authentication type of wireless  client and RADIUS server both to 
PEAP_TLS. 
3.  Disable the wireless connection and enable again. 
4.  The DUT will send the users certif icate to the RADIUS server, and then 
send the message of authentication result to PC2. 
5.  Windows XP will prompt that the aut hentication process is success or fail 
and end the authentication procedure. 
6.  Terminate the test steps when PC2 get dynamic IP and PING remote host  successfully. 
 
 
 
 
  
						

							
 83
Support Type: The router supports the types of 802.1x Authentication: 
             PEAP-CHAPv2 and PEAP-TLS. 
Note. 
1.  PC1 is on Windows XP platform without Service Pack 1. 
2.  PC2 is on Windows XP platform with Service Pack 1a. 
3.  PEAP is supported on Windows  XP with Service Pack 1 only. 
4.  Windows XP with Service Pack 1 allows  802.1x authentication only when data encryption 
function is enable.  
						

							
 84
 
A
A
A p
p
p p
p
p e
e
e n
n
n d
d
d i
i
i x
x
x  
 
  C
C
C  
 
   
 
  W
W
W P
P
P A
A
A -
-
- P
P
P S
S
S K
K
K  
 
  a
a
a n
n
n d
d
d  
 
  W
W
W P
P
P A
A
A  
 
 
 
 
 
Wireless Router: LAN IP: 192.168.1.254 
             WAN IP: 192.168.2.216 
Radius Server: 192.168.2.1 
UserA : XP Wireless Card:Ti-11g 
Tool: Odyssey Client Manager 
Refer to:  www.funk.com
  
Download:  http://www.funk.com/News&Events/ody_c_wpa_preview_pn.asp
 
    
						

							
 85
 
Or Another Configuration: 
  
 
WPA-PSK 
 
In fact, it is not necessary for this functi on to authenticate by Radius Server, the client 
and wireless Router authent icate by themselves. 
 
Method1: 
1. Go to the Web manager of Wirele ss Router to configure, like below: 
  
 
 
2. Go to Odyssey Client M anager, first choose “Network” 
  Before doing that, you should verify if  the software can show the wireless card. 
 Open “Adapters”    
						

							
 86
  
 
3. Add and edit some settings: 
 
  
						

							
 87
4. Back to Connection: 
  Then Select “Connect to network” You will see: 
 
 
Method2: 
1. First, patch windows XP and have to install “Service package 1” 
Patch: 
http://www.microsoft.com/downloads/det ails.aspx?displaylang=en&FamilyID=5039
ef4a-61e0-4c44-94f0-c25c9de0ace9 
2. Then reboot. 
3. Setting on the router and client: 
 Router: 
 
 
 
 
 
Client: 
Go to “Network Connection”  and select wireless adapter.  
						

							
 88
Choose “View available Wireless Networks” like below: 
AdvancedÆ choose “123kk” 
 
  
						

							
 89
WPA:   
 
For this function, we need the server to authenticate. This function is like 802.1x. 
 
The above is our environment: 
 
Method 1: 
1. The UserA or UserB have to get certificate from Radius, first. 
http://192.168.122.1/certsrv
 
account : fae1 
passwd : fae1 
 
 
2. Then, Install this certificate and finish. 
3. Go to the Web manager of Wirele ss Router to configure, like below: 
  
						

							
 90
 
 
4. Go to Odyssey Client Manager, choose “P rofiles” and Setup Profile name as “1” 
 
 
 
Login name and password are fae1 and fae1. 
Remember that you get certific ate from Radius in Step1.