Aiphone IS IP Standard Setting Manual

21
GETTING STARTED USING THE SYSTEM APPENDIX
SETTING THE SYSTEM
Registering areas and remote sites 
[System setting – Area/Site registration] 
Required
Register areas (for separating stations in your site) and/
or remote sites. The number to which a name is entered is 
registered as an area or site number. Up to 99 areas and/or 
sites (up to 31 for sites only) can be registered.
Click 1 Area/Site registration in the table of contents.
Enter an area name in the cell for the area number 01.2 
Be sure to...

22
Registering IP units [System setting – IP 
unit registration]
Register IP units by selecting from the connected ones to the 
system. 
To register a PC master station, fi rst install the application 
* (IS-SOFT) to a PC, then connect the PC to the network and 
then start IS-SOFT.
Click 1 IP unit registration in the table of contents.
Click 2 IP unit search.
All the IP units connected to the system are displayed in 
the [Search result] on the lower side of the window.
If IP units are not displayed,...

23
GETTING STARTED USING THE SYSTEM APPENDIX
SETTING THE SYSTEM
Registering stations and PA outputs 
[System setting – Registering stations]
Register all the stations and PA outputs connected in the 
system, and set the area, station no., station name (or PA 
output name) and type of station (for sub stations: video door/
audio door/room sub stations other than IP stations) to them. 
Click 1 Registering stations in the table of contents.
Set the area, station no., station name and type of 2 station (for...

24
Making detailed settings to stations and 
control units
[System setting – Advanced station settings]
Make detailed settings for the registered stations and control 
units (other than the IP control unit). The settings can be made 
to a station or control unit individually, or multiple stations of the 
same type at a time. The setting items differ from the station 
or control unit type. First select a station (or stations) or control 
unit, and then open the “Advanced settings” window to make 
the...

25
GETTING STARTED USING THE SYSTEM APPENDIX
SETTING THE SYSTEM
B Settings on [Contact input] window (for room 
sub stations only)
Make settings for contact input.
[Contact type]:
• 
Select either Normally open (NO) or Normally closed (NC).
[Call priority/Answering the page]:• 
You can select the action of the station when detecting 
input between ‘calling with appropriate priority’ and 
‘answering the page’.
Select “Normal”, “Priority”, “Urgent” or “Answering the 
page”.
Close
• 
Click this to close the...

26
Making detailed settings to the central control 
unit(s), add-on control unit(s) or room sub 
control unit(s)  
NOTE:
Make the settings to the central control unit(s), add-on control 
unit(s) or room sub control unit(s) respectively. You cannot select 
multiple control units at the same time. 
The following setting item buttons are displayed in the 
“Advanced settings” window.
Click either the button * F or G to open the 
corresponding setting window, and then make the 
settings in the displayed...

27
GETTING STARTED USING THE SYSTEM APPENDIX
SETTING THE SYSTEM
Registering stations and PA outputs to zones
[
System setting – Zone setting]
Assign stations and PA outputs to the registered zones.
Click 1 Zone setting in the table of contents.
Select a zone from the pull-down menu.2 
Click 3 Reference to display all the registered stations 
in your site.
  Another window opens and the registered stations are 
displayed in the list.
Check to select the target stations.4 
Select stations in the following...

28
Registering daily chime schedule 
[Chime setting – Registering daily chime schedule]
Up to 10 daily schedules can be registered.
Click 1 Registering daily chime schedule in the table 
of contents.
[Schedule number]: 2 Select the schedule number to register the daily 
schedule from the pull-down menu.
[Schedule name]:
3 Enter the name of daily schedule.
Click 
4 Add to add programs.
Another window appears.
[Chime time]:5 Set the starting time (hour, minute and second).
[Sound source]:
6 Check [Sound fi...

29
GETTING STARTED USING THE SYSTEM APPENDIX
SETTING THE SYSTEM
H Settings on [Weekly schedule] setting window
Select either [Every week] or [Every other week].1) 
 Set the schedule start and end dates.2) 
The monthly calendar is displayed by clicking * 
Refer calendar and you can select the start and 
end dates.
If necessary, you can change the month by clicking 
* 
 or .
 Set one of the registered daily chime schedules or no 3) schedule to each day of the week. (Select one from the 
pull-down menu.)
I...

30
Setting transfer schedule 
[Transfer setting – Transfer schedule setting]
You can set a weekly transfer schedule and individual daily 
schedule.
The settings can be made 1 year ahead.
* 
Click 1 Transfer schedule setting in the table of 
contents.
Make the settings by clicking 
2 Weekly schedule 
and 
Individual schedule respectively to open the 
corresponding window.
Individual schedule*  should be clicked after the target 
date is clicked on the calendar.
Make the settings in the displayed...