Aiphone IS IP Standard Setting Manual

11
GETTING STARTED USING THE SYSTEM APPENDIX
SETTING THE SYSTEM
SYSTEM SETTING FLOW
First of all, make the network settings. The network setting method differs according to the network environment. Select the fl ow 
suitable for your network environment from the chart below, and start the network settings after you fully understand it. After the 
network settings are fi nished, make the other individual system settings. See P. 18-36 for the system setting details.
NOTE:
The system settings should be made...

12
Flow 1
(IP host unit: A static IP address is set, 
IP client units: IP addresses are assigned by the DHCP server automatically)
Search for the IP address of the IP host unit from the MAC 
address of the IP host unit by using IS_IPSEARCH.exe (in 
the CD-ROM included with the IP control unit (IS-IPC)). (If the 
address does not appear, repeat this step until it appears.) 
Then access the address from the browser on the PC. (→P. 17)
This address is the temporary one for the initial setting.*  
Connect...

13
GETTING STARTED USING THE SYSTEM APPENDIX
SETTING THE SYSTEM
Flow 2
(All units: Static IP addresses are set)
Write down the MAC addresses of all the IP units to be 
used in the system in advance by using the “Setting 
Information Memo” (→P. 38) etc.
The MAC address is labeled on each unit.
* 
Decide the static IP address for each IP unit.
Make the [Network setting: Individual] settings on each 
IP unit individually. (→ P. 19)
: Settings on the IP host unit 
: Settings on the IP client unitsSTART...

14
Flow 3
(All units: IP addresses are assigned by the DHCP server automatically)
Write down the MAC addresses of all the IP units to be used 
in the system in advance by using the “Setting Information 
Memo” (→P. 38) etc.
The MAC address is labeled on each unit.
* 
Set the router (or DHCP server) so that it assigns a static IP 
address to the IP unit to be used as the IP host unit.
: Settings on the IP host unit 
: Settings on the IP client unitsSTART
Connect the units and the PC used for settings to...

15
GETTING STARTED USING THE SYSTEM APPENDIX
SETTING THE SYSTEM
Complete the network settings for your site by following  
Flow 1,  Flow 2 or  Flow 3. (→P. 12-14)
Get the following information for the remote sites you will 
connect with your site.
Global IP address
Connection port: global
Connection Password
Set the following setting items on the IP host unit. (→ P. 19)
[Network setting: Individual] :
Default Gateway
[Network setting: Common] :
UPnP
Global IP address
Audio/video port
Make the [Area/Site...

16
STARTING UP THE SYSTEM AND PREPARING FOR THE SETTINGS
The system settings are mainly made on the PC by accessing the web browser for the settings incorporated with the IP control unit 
(IS-IPC) as the IP host unit. It is recommended to use only one PC for the settings that is connected to the system.
System requirements for PC
Your PC and operating environment must meet the following system requirements to make the settings. 
Network 10BASE-T Ethernet, 100BASE-TX Ethernet
Web browser Internet Explorer...

17
GETTING STARTED USING THE SYSTEM APPENDIX
SETTING THE SYSTEM
Press down the I side of POWER switch to turn on 2 the unit.
It may take long until the unit gets started.* 
Turn on all the units constituting the system depending * on the network setting method.
The status LED of an IP video door station changes from 
* red lighting to orange blinking. 
(When the settings have correctly made, it changes to 
orange lighting.) 
The status LED of an IP master station changes from red 
lighting to red...

18
THE SYSTEM SETTING DETAILS
The basic setting procedure
When you have logged in to the system, the setting window appears. You can make the settings on this window.
Make sure to refer to the on-screen instructions and comments displayed on each window when you make the settings.
* 
Depending on the PC and its OS or environment, the display may differ.* 

The setting procedure
Click a title in the table of contents on which you wish to make the settings.
1 
The setting window of the title is displayed....

19
GETTING STARTED USING THE SYSTEM APPENDIX
SETTING THE SYSTEM
Making network settings to each IP unit 
[Network setting: Individual]
Make the settings for network to each IP unit connected 
to the system according to your requirements. 
Click 
1 Network setting: Individual in the table of 
contents.
Make the settings on the following items displayed in 2 the setting window.
[Host unit setting]:• 
Set this unit as either “Host unit” or “Client unit”. When set to 
“Client unit”, also enter the IP address...

20
Setting the administrator ID and password
[Administrator setting]
We recommend that you change the administrator ID and 
password from default to unique ones for security purposes.
This setting can be made to each of the IP units in your site.
* 
“aiphone” is preset as the default for both ID and password.* 
Click 1 Administrator setting in the table of contents.
Make the settings on the following items displayed in 2 the setting window.
[New administrator ID]:• 
Enter the new ID.
[Current Password]:...