Home > Aimco Brakes > Monitors > Aimco Brakes Monitor UECD4800 Instruction Manual

Aimco Brakes Monitor UECD4800 Instruction Manual

Here you can view all the pages of manual Aimco Brakes Monitor UECD4800 Instruction Manual. The Aimco Brakes manuals for Monitors are available online for free. You can easily download all the documents as PDF.

Page 1

PO Box 16460, Portland, OR  97292-0460
  

 
503-254-6600 

   
Fax 503-255-2615  
Combo Controller for 
Electric Pulse UEP-MC Tool 
UECD-4800 
Instruction Manual 
 www.aimco-global.com 

Page 2

1
Table of Contents
1.Safety Instructions 
...............................................
2. Outline .....................................................
2.1.
Configuration 
...............................................
2.2. LCD Screen Diagram (1) 
........................................
2.3.LCD Screen Diagram (2) 
........................................
2.4.Dimensions 
................................................
2.5. Features 
..................................................
2.6....

Page 3

2
1.Safety Instructions
Do pe

ruse this instruction manual before insta llation, operation, maintenance and inspection of 
this system, and the use this system properly.    Use this system only after you master knowledge 
of this equipment, safety instruction and all instruct ions given in the safety instructions of this 
system. Take note that this operat ion manual classifies the safety instructions into two signs; 
“DANGER” and ”WARNING”, according to  the degree of seriousness and urgency....

Page 4

3
DANGER
●Be sure to turn off the power switch prior to wiring to avoid an electric shock or a fire.
●Place the no fuse breaker (NFB).    There may be a fire risk.
●Make sure that the cords and outlets are proper ly grounded to avoid an electric shock or a
fire.
●Carry out wiring after you installed controlle r to avoid an electric shock or a fire.
●Never use the power code for dragging the UEP tool and pull it out roughly.    There may be
an electric shock or fire risk.
●Wiring must be carried out by an...

Page 5

4
WARNING
●The excessive operation causes the motor unit and driver unit to be overheated.    Do not run
the system excessively or more than necessary.    Never touch the motor unit or rotating part in
operation or immediately after the system is swit ched off.    There may be an injury or burn risk.
●Never overwork the system more than it is intended.    There may be an injury or burn risk.
●Run the system in a good workstation.    The awkward posture in operation is dangerous.
●Be careful to run the...

Page 6

5
Danger
●Never dismantle the system locally to avoid an injury and fire risk.
●Stop the operation and disconnect the system  from electricity immediately in emergency.
◆Miscellaneous Concern
●Note that the drawings and pictures in this  manual may not list all the accessories needed for
safety measure to explain the details.    Be sure  to put the accessories back to the system as
specified in this manual before  operation and run it as intended.
●Never let anyone other than the operator in operation...

Page 7

6
2.Outline
2.1.  Configuration
PC for Setup 
Front Panel of UECD-4800 Rear Panel of UECD-4800 
PLC 
Serial Printer 
PLC
PC 
Hub 
Receptacle 
Note) Make sure to earth 
when 2-pin adaptor is in 
use.
 
Power Cable
PC Cable
 
LAN Cable 
PC, UEC or etc.
 
Tool 
Tool Cable  

Page 8

7
2.2. LCD Screen Diagram (1)  
 
 
 
 
 
SETTING #1■■(2/4) 
→DATA■OUT
■TOOL■CONTROL
■IN/OUT■PUT
DISPLAY■SELECT 
→SETTING
■CHECK■SELECT
■ZERO■SET
SETTING■WORK■NO(3/3) 
→WORK■NO.7(#7) 
■WORK■NO.8(#8)
SETTING■WORK■NO(2/3) 
→WORK■NO.4(#4) 
■WORK■NO.5(#5)
■WORK■NO.6(#6)
SETTING■WORK■NO(1/3) 
→WORK■NO.1(#1) 
■WORK■NO.2(#2) 
■WORK■NO.3(#3)
SETTING■#1■■(1/4) 
→BASIC
■MODE■■■■
■TIMER
IN/OUT■CHECK■SELECT 
→KEY■■■■■CHECK
■INPUT■■■CHECK
■OUTPUT■■CHKCK
INPUT■CHECK 
■INPUT1■■■■INPUT4
■INPUT2■■■■INPUT5
■INPUT3...

Page 9

8
2.3. LCD Screen Diagram (2)  
1 
TIMER■#1■■■■■■■
(6/6) 
→ジカン■■■■■■■■■■
■0013 
TIMER ■#1■■■■■■■
(5/6) 
→ネン■■■■■■■■■■■
■■0007 
TIMER ■#1■■■■■■■
(4/6) 
→ギャクテン■チエン■■■■■0300
■ ピンアワセ■ ヨウ■■■■■■
TIMER ■#1■■■■■■■
(3/6) 
→スタート■トルク■イジョ■■0500 
■サイクル■オーバ■イジョ■9999
TIMER ■#1■■■■■■■
(2/6) 
→シメツケ■ OK■■■■■■■■
9999 
TIMER ■#1■■■■■■■
(1/6) 
→JUDGMENT DELAY ■■0300
■INITIAL ERROR■  ■0500 
MODE■#1■■■■■■(11/11) 
→PC■ ソクド■センタク■■■■
■■3 
■ ハケイ■ メモリ■キノウ■■■■■■
MODE■#1■■■■■■(10/11) 
→カクドCUT ■■■■■■■■■
999...

Page 10

9
2.4. Dimensions 
36 36 150 
5 
200 
59 170 
36 
Side Panel Front Panel
24 
Front Panel  Rear Panel  
Start reading Aimco Brakes Monitor UECD4800 Instruction Manual

Related Manuals for Aimco Brakes Monitor UECD4800 Instruction Manual

All Aimco Brakes manuals