Aimco Brakes Cordless Tool UDBPT Series 40 50 60 70 Operation Instructions User Manual

- 11   -Hand ling point
４   Torque adjustment  in forward rotation (CW) only  
・ Release hands from   trigger, then remove the battery from the tool.
・ Insert an allen key in the hole to adjust relief valve as follow.
・ Never touch oil plug.   Removal of oil plug will result in leakage and to ol
requiring service .
   Allen key for torque adjustment   (supplied)  
(1.5mm hexagon)  
Oil plug: Never touch!  
Line r CP  
 
Slit
s
Relief valve   

- 12   -Handle Operation
５   Changeable Fwd/Rev Lever (if desired)  
 
 
 
 
１） Remove allen bolt (use 2mm hexagon bar spanner).
２） Pull reverse lever forward to r emove it.
３） Change the position and push it back to the tool.
４） Put glue (#221 LOCTITE is recommended) to thread of allen bolt and fix reverse
lever  to  the  tool  by  fastening  the  allen  bolt  by  fastening   torque  0.3~0.5Nm.
６   Battery gauge LED  
Battery gauge   LED will light for about 3 seconds first and then  indicate   the...

- 13   -Handling point
７   Press the trigger and the LED will light in white.
  Avoid staring at LED.  
１   Factors that affects fastening torque  
Fastening torque can change even for the same size bolt because of torque 
coefficient determined by finishing status of the bo lt or the work such as industrial 
quality ranking of the bolt or the length.    
２   Socket and anvil clearance  
Use of worn or poorly engaging sockets will result in inaccurate torque delivery and 
potentially damage the tool.  It...

- 14   -CAUTION  Battery charger  
UDBP  utilizes   lithium ion battery.  
１   Battery replacement interval  
・ Batteries may be charg ed up to   500 times after full discharge.   This  number
of times can change depending upon the operati ng   conditions.  Consider
that the battery has come to an end and replace with a new one when
number of fasteners per full charge gets about a half of new ba ttery condition.
２   Storage of battery  
・ Make sure to do full charge of the battery when you  have not used...

- 15   - Attach  Jaw  
Remove  Battery and the charger  
Charge brand - new battery completely before   
first use of the tool. Su spension of battery charging 
prematurely can cause the LED to incorrectly   
display remaining   capacity ( ＊ 2).    
( ＊ 2): Charge the battery full 2 to 3    
times and the display will get back to normal.  
１   Attach and remove battery  
Attach ・・・ Slide it until it give s out click sound.  
Remove ・・ Slide it to your side while pressing down the Jaw.  
２   Charge...

- 16   -Troubleshooting  
Check the following before you ask for repair. 
When  C harging  
Sympt om   Potential Cause   Remedy  
Waiting lamp lights   Battery is overheated   Charge only room 
temperature batteries  
Battery error lamp lights.   Battery  is  damaged  or  at 
the end of it’s service life   Replace  the  battery  with 
a new one.  
While in Operation
Symptom   Potential Cause   Remedy  
Tool Does not Run   Battery depleted   Recharge the battery.  
The tool gets hot.   Tool has been...

- 17   -Maintenance  
   1   Check for  any loose parts , breakage,  or  wear  of all parts prior to each use .  
   1    Maintenance  
・ Casing is m ade of plastic.  W ipe it by soft cloth.  Do not use volatile liquid s   or
wet cloth because doing so will cause deterioration /discoloration of the
materials .
   2    Store the tool in  a place that remains between 0° -   40 ℃ ,    is  moisture free, 
  du st free,  and  free from direct rays of the Sun. 
   3    Periodic inspection  
・ It is  Recommend...

Notes: 

- 
18 - 

- 
19 - AIMCO CORPORATE   HEADQUARTERS   AIMCO CORPORATION DE MEXICO SA DE CV  
10000 SE Pine Street   Ave. Cristobal Colon 14529  
Portland, Oregon  97216   Chihuahua, Chihuahua.  31125  
Phone: (503) 254 – 6600   Mexico  
Toll Free: 1 - 800 - 852 - 1368   Phone: (01 - 614) 380 - 1010  
Fax: (01 - 614) 380 - 1019  
AIMCO CHINA   AIMCO EUROPE  
Room 607, No. 3998 Hongxin Rd Dibao Plaza   Avenida Río Gallo, 431  
Minhang District, Shanghai    19174 Galápagos  -   Guadalajara  
China   Spain  
Phone: 0086...