Aimco Brakes Cordless Tool UDBPT Series 40 50 60 70 Operation Instructions User Manual

UDBP - T   Series 40, 50, 60 & 70  
Lithium Ion Battery - powered   
Direct Drive Auto - shutoff Pulse  
  INSTRUCTION MANUAL  
PO Box 16460, Portland, OR 
 97292-0 460  503-25 4-6600   Fax 503-2 55-2615  www.aimco-global.com  

- 2   -Indicates a critical operating step that must 
be followed. Carefully  read this instruction for 
safe  use, understand the contents, and use 
the tool properly.  Keep   this manual.    
Indicates that incorrect handling may  create a  
hazardous condition, resulting in  injury to an 
operator   or physical damage   to the tool .  
For safety operation  
・ Basic desig n   of this tool is  a   lithium ion battery - powered brushless motor
rotat ing an   oil pulse unit, which convert s   the...

- 3   -4. Do not allow unauthorized persons  at the worksite .   Tool should be used
by trained adult personnel and kept away from all children .
5. Use  correct   charger ,  power cord ,   and battery   with this tool .
Do not charge the battery by other charger.  Do not use our charge r   for
other  maker’s  batteries.
Doing so c ould result in   battery explosion resulting in  property  damage or
injuries.
6. Read this manual car efully, and charge the battery properly.
・ Use the charger by the...

- 4   -11. Release your finger from the trigger, and remove  the battery from the tool
when ever performing the following:
・ Torque adjustment.
・ Replace driver bit or socket.
・ R epair ing   the tool.
12. Wash your eyes  should any  battery liquid   get to   your eyes, and have
your eyes examined and medically treated by   an   eye care d octor
immediately.
13. Do not use battery whose  running   time per charge  becomes short .
14. Make sure that your hand is off the trigger when you remove the...

- 5   -1. Proper fastening time
・ Battery pulse tool will allow tightening an average of 6 cycles
per minute when averaged on a B joint .    Softer joints will require
less aggressive duty cycles.
・ Temperature protection will function to stop the tool when motor
heats due to  exceeding duty cy cle .
2. Operation  at low temperature extremes
・ The tool operates using a pulse unit containing hydraulic fluid.
Should tool be left for extended periods at temperatures below 5°C,
the tool may not deliver...

- 6   -4. Cautions for tool ’ s operation
・ Confirm that  no person interferes with work environment or is in a
hazardous position .
・ Stop the op eration at once,  and request service if abnormalities are
found with the tool’s operation .
5. Do not do reckless ly   handl e   the power cord of the charger.
・ Do not pull or hold the power cord to disconnect the power cord or
carry the charger.
・ Arrange the power co rd so it may not be stepped   on , caught,   or
stressed. Not doing so can cause early...

- 7   -11. Overload protect function of motor
・ Th is function will work to stop the motor when  the anvil becomes
locked for about 1 second   with the trigger depressed .
12. Use appropriate tool whose capacity can cover the requirements of your
work.
・ Only connect sockets or bits appropriate to the size of the to ol anvil .
13. Perform regular maintenance inspections .
・ Check power cord for damages periodically,  request replacements
if damage is observed .
・ Maintain handle g rips in a clean, dry...

- 8   -18. Do not give battery shock due to  drops .  Do not throw batteries.
Doing so will deform batteries,  destroy   integrated protection circuit, can
result in a   charge  of  the battery by abnormal current  or   voltage   resulting
in damage or injury .
19. Do not drive a nail into battery, hit battery by  hammer , or  impact   the
battery.   Doing so can deform battery,  destroy   integrated protection circuit,
and become  a  cause of heat, explosion, or fire.
20. Do not  attempt to   solder...

- 9   -Parts Name  
  Shut - off LED Lamp  
Torque Adjust Allen Wrench  
Specifications  
Ambient temperature:  0 ～ 40 ℃  
Rotating speed change: 3 steps  
Slow speed:  500rpm → 1 , 000rpm   for socket and bolt entry and tentative fastening  
Free speed:  4 , 800rpm   for regular fastening  Trigger  
Reverse   Lever  
Battery   

- 10   -Handl e Controls  
１   Select rotating direction   (factory supplied lever orientation)  
Set LEVER  to R ：   Forward   Set LEVER to L   ：   Reverse  
２   Press trigger  
1 ） Speed  increases in   3 steps as you press the trigger   progressively   for both
forward and reverse.
2 ） Release your finger from the trigger, and the brake will work to stop the
tool.
３   Fastening  
・ Fastening torque does not reach preset torque if you
release   trigge r   prior to   automatic shut - off.
・ Do not cover...