AEG Steam oven BS730470KM User Manual

							When the water hardness exceeds the
values in the table, fill the water drawer
with bottled water.
1. Take the four colour change strip
supplied with the steam set in the
oven.
2. Put all the reaction zones of the strip
into the water for approximately 1
second.
Do not put the strip into the running water!
3. Shake the strip to remove the excess
of the water.
4. After 1 minute check the hardness of
the water according to the table
below.
The colours of the reaction zones
continue to change after 1 minute.
Do not consider this in the
measurement.
5. Set the hardness of the water in the
settings menu. Refer to the "Using
the settings menu".Test stripHardness of the
water1234
The black squares in the table
correspond to red squares on the test
strip.
You can change the hardness level of the
water in the menu settings menu.
After a power cut you do not have to set the hardness level of the water again.
6.  DAILY USEWARNING!
Refer to Safety chapters.6.1  Operating the appliance
To operate the appliance you can use:
•the manual mode
• automatic programmes6.2  Oven functionsOven functionApplicationTrue Fan Cook-
ingTo bake on up to three shelf positions at the same time
and to dry food. Set the temperature 20 - 40 °C lower
than for Top / Bottom Heat.Pizza SettingTo bake food on one shelf position for a more intensive
browning and a crispy bottom. Set the temperature 20
- 40 °C lower than for Top / Bottom Heat.Slow CookingTo prepare tender, succulent roasts.Top / Bottom
HeatTo bake and roast food on one shelf position.Frozen FoodsTo make convenience food like e.g. french fries, potato
wedges or spring rolls crispy.ENGLISH11            
						

							Oven functionApplicationTurbo GrillingTo roast larger meat joints or poultry with bones on
one shelf position. Also to make gratins and to brown.GrillingTo grill flat food and to toast bread.Fast GrillingTo grill flat food in large quantities and to toast bread.Keep WarmTo keep food warm.Bottom HeatTo bake cakes with crispy bottom and to preserve food.DefrostThis function can be used for defrosting frozen foods,
such as vegetables and fruits. The defrosting time de-
pends on the amount and size of the frozen food.Moist Fan BakingTo prepare baked goods in tin on one shelf position.
To save energy during cooking. This function must be
used in accordance with the cooking tables in order to
achieve the desired cooking result. To get more infor-
mation about the recommended settings, refer to the
cooking tables. This function was used to define the
energy efficiency class acc. to EN 60350-1.Bread BakingUse this function to prepare bread and bread rolls with
a very good professional-like result in terms of crispi-
ness, colour and crust gloss.Steam Regener-
atingFood reheating with steam prevents surface drying.
Heat is distributed a gentle and even way, which allows
to recover taste and aroma of food as just prepared.
This function can be used to reheat food directly on a
plate. You can reheat more than one plate at the same
time, using different shelf positions.Quarter Steam +
HeatTo bake bread, roast large pieces of meat or to warm
up chilled and frozen meals.Half Steam +
HeatFor dishes with a high moisture content and for poach-
ing fish, custard royale and terrines.Full SteamFor vegetables, fish, potatoes, rice, pasta or special
side-dishes.The lamp may automatically
deactivate at a temperature
below 60 °C during some
oven functions.6.3  Setting the oven function
1. Activate the appliance with 
 or .
www.aeg.com12                
						

							The display shows the set temperature,
the symbol and the number of the oven function.
2. Touch 
 or  to set an oven
function.
3. Touch 
 or the appliance starts
automatically after five seconds.
If you activate the appliance
and do not set an oven
function or programme, the
appliance deactivates
automatically after 20
seconds.6.4  Changing the temperature
Touch  or  to change the
temperature in steps of 5 °C.
When the appliance is at the set
temperature, an acoustic signal sounds
three times and the Heat up indicator goes out.
6.5  Checking the temperature
You can see the temperature in the
appliance when the function or
programme operates.
1. Touch 
.
The Temperature / Time display shows the temperature in the appliance.
2. Touch 
 to go back to the set
temperature or the display shows it automatically after five seconds.
6.6  Fast heat up functionDo not put food in the oven
when the Fast heat up
function operates.
The Fast heat up function is not available with every oven function. An acoustic
signal sounds if the Fast heat up function
is not available for the set function if
Faulty tone is activated in the settings menu. Refer to "Using the settings
menu".
The Fast heat up function decreases the
heat up time.
To activate the Fast heat up function
touch and hold 
 for more than three
seconds.
If you activate the Fast heat up function,
the bars on the display 
 flash one by
one and 
 comes on to show that
the function operates.
6.7  Steam cooking
The water drawer cover is in the control
panel.
WARNING!
Use only water as the liquid.
Do not use filtered
(demineralised) or distilled
water.
1. Press the cover of the water drawer
to open it.
2. Fill the water drawer with cold water
to the maximum level (around 950
ml) until the acoustic signal sounds or the display shows the message.
The water supply is sufficient for
approximately 50 minutes.
Do not fill the water drawer over its maximum capacity. There is a risk of
water leakage, overflow and furniture
damages.
3. Push the water drawer to its initial
position.
4. Activate the appliance.
5. Set the steam function (refer to the
"Oven functions" table) and the
temperature.
6. If necessary, touch 
 to set the
DURATION 
 or END  function
(refer to "Setting the END" or
"Setting the DURATION").
The first steam shows after
approximately 2 minutes. An acoustic
signal sounds when the appliance is at
approximately the set temperature. The signal sounds again at the end of the
cooking time.
7. Touch 
 to deactivate the acoustic
signal and the appliance.
ENGLISH13                  
						

							7. CLOCK FUNCTIONS7.1  Clock functions tableClock functionApplicationTIME OF DAYTo show or change the time of day. You can change the
time of day only when the appliance is on.DURATIONTo set how long the appliance operates.ENDTo set when the appliance deactivates. TIME DELAYTo combine DURATION and END function.SET+GOTo start the appliance with necessary settings with only
one touch of the sensor field any time later.MINUTE MINDERTo set a countdown time. This function has no effect on
the operation of the oven. You can set the MINUTE
MINDER at any time and also when the appliance is off.00:00COUNT UP TIMERTo set the count up, which shows how long the appli-
ance operates. This function has no effect on the opera-
tion of the appliance. It is on immediately when the oven
starts to heat. The COUNT UP TIMER is not activated if
DURATION and END are set.7.2  Setting and changing the
time
After the first connection to the mains,
wait until the display shows 
 and  12:00 .
" 12 " flashes.
1. Touch 
 or  to set the hours.
2. Touch 
 or .
3. Touch 
 or  to set the minutes.
4. Touch 
 or .
The display shows the new time.
To change the time of day touch 
again and again until  starts to flash.
7.3  Setting the DURATION
1.Set an oven function and
temperature.
2. Touch 
 again and again until starts to flash.
3. Use 
 or  to set the minutes for
DURATION time.
4. Touch  or the DURATION time
starts automatically after 5 seconds.
5. Use 
 or  to set the hours for
DURATION time.
6. Touch 
. The DURATION time
starts automatically after 5 seconds.
When the set time ends, an acoustic
signal sounds for 2 minutes. 
 and time
setting flash in the display. The appliance deactivates.
7. Touch a sensor field or open the
oven door to stop the acoustic
signal.
8. Turn off the appliance.
7.4  Setting the END
1.Set an oven function and
temperature.
2. Touch 
 again and again until starts to flash.
3. Use 
 or  to set the END and
 or  to confirm. First you set the
minutes and then the hours.
www.aeg.com14                                  
						

							When the set time ends, an acousticsignal sounds for 2 minutes. 
 and the
time setting flash in the display. The
appliance deactivates automatically.
4. Touch a sensor field or open the
oven door to stop the acoustic
signal.
5. Turn off the appliance.
7.5  Setting the TIME DELAY
function
1. Set an oven function and
temperature.
2. Touch 
 again and again until starts to flash.
3. Use 
 or  to set the minutes for
DURATION.
4. Touch 
.
5. Use 
 or  to set the hours for
DURATION.
6. Touch 
, the appliance switches to
the setting of the END function.
The display shows flashing 
.
7. Use 
 or  to set the END and
 or  to confirm. First you set the
minutes and then the hours.
Appliance turns on automatically later on, works for the set DURATION time
and stops at the set END time. At the set
time an acoustic signal sounds for 2
minutes. 
 and the time setting flash in
the display. The appliance deactivates
automatically.
8. Touch a sensor field or open the
oven door to stop the acoustic
signal.
9. Turn off the appliance.
When the Time delay
function is activated, the
display shows a static
symbol of the oven function,
 with a dot and . The
dot shows which clock
function is on in the Clock /
residual heat display.
7.6  Setting the SET+GO
You can use the SET+GO function only
when the DURATION is set.
1. Set an oven function (or a
programme) and temperature.
2. Set the DURATION.
3. Touch 
 again and again until flashes in the display.
4. Touch 
 to set the SET+GO
function.
The display shows 
 and  with an
indicator. This indicator shows which
clock function is activated.
5. Touch a sensor field (apart from ON /
OFF) to start the SET+GO function.
7.7  Setting the MINUTE
MINDER
1. Touch .
 and "00" flash in the display.
2. Use 
 to switch between options.
First you set the seconds, then the
minutes and the hours.
3. Use 
 or  to set the MINUTE
MINDER and 
 to confirm.
4. Touch 
 or the MINUTE MINDER
starts automatically after 5 seconds.
When the set time ends, an acoustic
signal sounds for 2 minutes and 00:00
and 
 flash in the display.
5. Touch a sensor field or open the
oven door to stop the acoustic
signal.
7.8  COUNT UP TIMER
1.To reset the Count Up Timer, touch
 again and again until  flashes in
the display.
2. Touch 
 until the display shows
"00:00" and the Count Up Timer
starts to count up again.
ENGLISH15                                   
						

							8. AUTOMATIC PROGRAMMESWARNING!
Refer to Safety chapters.
There are 25 automatic programmes.
Use an automatic programme or recipe
when you do not have the knowledge or experience on how to prepare a dish.The display shows the default cooking
times for all automatic programmes.8.1  Automatic programmesProgramme numberProgramme name1VEGETABLES, TRADITIONAL2POTATO GRATIN3FARMER BREAD4ROLLS5FISH6POACHED FISH (TROUT)7PLUM DUMPLING8VEAL KNUCKLE9RICE10LASAGNE11DOUGH PROVING12BRAISED MEAT13ROAST PORK14ROAST VEAL15ROAST LAMB16ROAST GAME17WHOLE CHICKEN18PIZZA19QUICHE LORRAINE20LEMON SPONGE CAKE21CHEESE CAKE22CANNELLONI23CONVENIENCE CAKE24CONVENIENCE PIZZA25CONVENIENCE POTATO TYPESwww.aeg.com16  
						

							8.2 Recipes onlineYou can find the recipes for
the automatic programmes
specified for this appliance
on our website. To find the
proper Recipe Book check
the PNC number on the
rating plate on the front
frame of the appliance
cavity.8.3  Automatic programmes
1.Activate the appliance.
2. Touch 
.
The display shows 
, a symbol and the
number of the automatic programme.
3. Touch 
 or  to choose the
automatic programme.
4. Touch 
 or wait five seconds until
the appliance automatically starts to
work.
5. When the set time ends, an acoustic
signal sounds for two minutes. The
symbol 
 flashes.
6. Touch a sensor field or open the
oven door to stop the acoustic
signal.
7. Deactivate the appliance.
8.4  Automatic programmes
with weight input
If you set the weight of the meat, the
appliance calculates the roasting time.
1. Activate the appliance.
2. Touch 
.
3. Touch 
 or  to set the weight
programme.
The display shows: the cooking time, the
duration symbol 
, a default weight, a
unit of measurement (kg, g).
4. Touch  or the settings save
automatically after five seconds.
The appliance activates.
5. You can change the default weight
value with 
 or . Touch .
6. When the set time ends, an acoustic
signal sounds for two minutes. 
flashes.
7. Touch a sensor field or open the
oven door to stop the acoustic
signal.
8. Deactivate the appliance.
8.5  Automatic programmes
with the core temperature
sensor (selected models)
The core temperature of the food is
default and fixed in programmes with the
core temperature sensor. The
programme ends when the appliance is
at the set core temperature.
1. Activate the appliance.
2. Touch 
 again and again until the
display shows 
.
3. Install the core temperature sensor.
Refer to "Core temperature sensor".
4. Touch 
 or  to set the
programme for the core temperature
sensor.
The display shows the cooking time, 
and .
5. Touch 
 or the settings save
automatically after five seconds.
When the set time ends, an acoustic
signal sounds for two minutes. 
flashes.
6. Touch a sensor field or open the
door to stop the acoustic signal.
7. Deactivate the appliance.
9. 
USING THE ACCESSORIESWARNING!
Refer to Safety chapters.9.1  Core temperature sensor
There are two temperatures to be set: the oven temperature and the coretemperature.ENGLISH17                          
						

							The core temperature sensor measures
the core temperature of the meat. When the meat is at the set temperature, theappliance deactivates.CAUTION!
Only use the core
temperature sensor supplied or the correct replacement
parts.The core temperature sensor
must stay in the meat and in
the socket during the
cooking.
1. Activate the appliance.
2. Put the point of the core temperature
sensor (with 
 on the handle) into
the centre of the meat.
3. Put the plug of the core temperature
sensor into the socket at the front of
the appliance.
The display shows  flashing and the
default set core temperature. The
temperature is 60 °C for the first
operation, and the last set value for each subsequent operation.
When you put the core
temperature sensor into the
socket, you cancel the
settings for the clock
functions.
4. Touch  or  to set the core
temperature.
5. Touch 
 or the settings save
automatically after 5 seconds. 
You can set the core
temperature only when
 flashes. If  is in the
display but does not
flash before you set the
core temperature, touch
 and  or  to set
a new value.
6. Set the oven function and the oven
temperature.
The display shows the current core
temperature and the heat up symbol 
.
While the appliance calculates the
approximate duration time, the display shows the count up time. After the firstcalculation the display shows the
approximate duration of the cooking
time.
The appliance continues to calculate the
duration during the cooking. The display
updates at intervals with the new
duration value.
When you cook with the
core temperature sensor,
you can change the
temperature shown in the
display. After you put the
core temperature sensor in
the socket and set an oven
function and temperature,
the display shows the
current core temperature.
Touch 
 again and again to
see three other
temperatures: • the set coretemperature
• the current oven temperature
• the current core temperature.
When the meat is at the set core
temperature, an acoustic signal sounds
for two minutes and the value of the core
temperature and 
 flash. The appliance
deactivates.
7. Touch a sensor field to deactivate
the acoustic signal.
8. Remove the core temperature sensor
from the socket and remove the
meat from the appliance.
www.aeg.com18                    
						

							WARNING!
Be careful when you remove
the core temperature
sensor. It is hot. There is a
risk of burns.9.2  Inserting the accessories
Wire shelf:
Push the shelf between the guide bars of
the shelf support and make sure that the
feet point down.
Deep pan:
Push the deep pan between the guide bars of the shelf support.
Wire shelf and the deep pan together:
Push the deep pan between the guide bars of the shelf support and the wireshelf on the guide bars above and make
sure that the feet point down.
Small indentation at the top
increase safety. The
indentations are also anti-tip
devices. The high rim
around the shelf prevents
cookware from slipping of
the shelf.9.3  Trivet and Grill- / Roasting
panWARNING!
Be careful when you remove
the accessories from a hot
appliance. There is a risk of
burns.
You can use the trivet to roast larger
pieces of meat or poultry on one shelf
position.
1. Put the trivet into the deep pan so
that the supports of the wire shelf
point up.
2. Put the deep pan into the oven on
the necessary shelf position.
You can use the trivet to grill flat dishes
in large quantities and to toast.
1. Put the trivet into the deep pan so
that the supports of the wire shelf
point down.
ENGLISH19         
						

							2.Put the deep pan into the oven on
the necessary shelf position.10.  ADDITIONAL FUNCTIONS10.1  Using My Favourite
Programme function
Use this function to save your favourite temperature and time settings for an
oven function or programme.
1. Set the temperature and time for an
oven function or programme.
2. Touch and hold 
 for more than
three seconds. An acoustic signal sounds.
3. Deactivate the appliance.
• To activate the function  touch 
.
The appliance activates your favourite programme.
When the function
operates, you can change
the time and
temperature.
• To deactivate the function  touch .
The appliance deactivates your
favourite programme.
10.2  Using the Child Lock
The Child Lock prevents an accidental
operation of the appliance.
1. To activate the function deactivate
the appliance with 
. Do not set an
oven function.
2. Touch and hold 
 and  at the
same time for 2 seconds.
An acoustic signal sounds.
SAFE comes on in the display.
To deactivate the Child Lock function
repeat step 2.10.3  Using the Function Lock
You can activate the function only when
the appliance operates.
The Function Lock prevents an
accidental change of the oven function.
1. To activate the function activate the
appliance.
2. Activate an oven function or setting.
3. Touch and hold 
 and  at the
same time for 2 seconds.
An acoustic signal sounds.
Loc comes on in the display.
To deactivate the Function Lock repeat
step 3.
You can deactivate the
appliance when the Function
Lock is on. When you
deactivate the appliance,
the Function Lock
deactivates.10.4  Using the settings menu
The settings menu lets you activate or
deactivate functions in the main menu.
The display shows SET and the number
of the setting.
DescriptionValue to set1SET+GOON / OFF2RESIDUAL HEAT INDICATORON / OFF3KEY TONE1)CLICK / BEEP / OFF4FAULTY TONEON / OFF5DEMO MODEActivation code: 2468www.aeg.com20